Ford - Explorer :: 1999 XLT Transmission Taking A Couple Of Seconds To Catch In Drive
Oct 4, 2013
I've had a 1999 explorer for a few months. The transmission has always taken a couple of seconds to "catch" in drive and was then fine. Today, I had to tow another car a short distance and now going into drive directly is useless.
I must shift into 2nd and then back into drive. Then, for the most part, the car drives fine unless I have to put it in Park or in Reverse. Then I must repeat the procedure.
The fluid is fresh and the dipstick shows a slight overfill. Is there anything I can do about this or is this the death of the transmission. If I can run it another couple of years, I'd be satisfied.
View 7 Replies
Advertisement
I have a 2003 ford explorer sohc 4.0l , that starts only with the gas peddle pushed to the floor and will only run for a couple of seconds at a time. Just replaced all the timing chains and tensioners. It has 145 lbs compression, and 60 psi fuel pressure. No codes on the computer.
View 8 Replies
I just got my ISF 3 weeks ago and this issue got me pretty worried. I would like to hear if there has been a recall or a fix on this issue. While in Drive (D), the tranny wouldn't shift past 2nd for a couple of seconds. It went as high as 4.5RMP and wouldn't shift, the RPM kept going up. Letting go off the gas did not work, the RMP just stood where it was and slowly decreased with the speed. This lasted for a few seconds. I must admit that I was just pulling out of the driveway and she wasn't properly warmed up (16 degrees temp or 60fh)...
View 7 Replies
1991 4x4 f250 idi w e4od w 3:55 ratio... The truck is slow to engage in reverse, about 5-10 sec. It also has a very hard shift 1-2. All other shift points are good. Drop down is good, and TC lock up happens at all the right points (feels like anyway).
I've had the truck for about 2 years now, replaced several sensors an harnesses and a full fluid change to solve other problems but this still remains.
Sometimes when I start it in the morning if I let it sit and idle for a few min it will engage reverse much quicker AND shifts way smoother and constant. Shifts smoothly thro all gears, holding a constant 1800-2000 rpms with no drop or lug. Or do I need a rebuild?
View 4 Replies
I have a 2006 F250 Lariat super Duty / 6.0 L engine / 143000+ miles / once started and transmission shifted into drive it takes 5 seconds or more for it to engage hard or if I build up the RMS then it jumps into gear hard, after it gets going it feels like I am driving on a washboard until it get warmed up good 10 mile or so. Is it the transmission filter and if so which one, I understand there is a small one on the outside of the transmission if so where? I can't find it.
View 14 Replies
I have a problem with my transmission slipping. It seems to happen most often when I have shifted from park into drive and am going uphill. I don't really notice a problem with it when I am on flats or even at red lights. It can drift backwards for 10-15 feet before "catching."
I don't feel any problem when I am going faster or in higher gears. 1999 Ford Explorer SOHC 6 Cyl 4.0...
View 11 Replies
I have a 2002 Ranger with a 2.3 lt engine and a 5R44E Transmission. Has 120,oookms (75,000 miles) I have an issue.
Here is what was happening: Would not shift into Drive...took a long time to do so.... and had a 2 to 3 gear flare.
Here is what I did: Replaced the valve body gaskets. Improved a lot. The 2 to 3 shift flare has gone. The delayed shift into D is mostly gone BUT still takes 15 to 20 seconds to shift into D. Once in gear no problems shifting. Does not slip and NO OD light flashing.
What do I need to do to fix the delayed shift issue.
View 9 Replies
I used the a/c for the first time this year on my 2013 F250 and heard some noises I don't remember hearing before. When the a/c(or defrost) is on every 12 sec or so I hear a hissing sound that lasts for a couple of seconds then goes away. Is this the compressor cycling and if so is it normal to hear it inside the cab?
I know it has to do with the a/c because if I shut it off as the hissing sound is being made the sound will instantly stop. Other than the noise the a/c works fine and blows cold air. Also, if it matters I have the standard control panel, not climate control.
View 8 Replies
Tried starting the truck, fired ran good for a couple seconds, then ran extremely rough for a couple seconds then died.
I did some research and changed the ICP because there was oil in the connector so even if it wasnt causing my issue i wanted to replace it.
Now I have the same issue but it will actually run a little longer and not stall. I thought it was fixed so i took it for a drive, after about 3 miles it bogged down and i was able to make it home with half throttle going about 30mph. Sounds almost like its running on half the cylinders. i unplugged the ICP and it continued to run that way.
I had done the 50cent mod a few years back with the peices from ford but i know the harnesses themselves can wear through so i checked the resistance between the center pin and the two pins to the right and left for both the injector harness and they had about 3ohms.
I am leaning towards an IPR but from the reading i have done it seams like most trucks will not restart after they die. I have AE so i am going to hook it up later today, just wanted some reccomendations on what to look at.
I also remember when i shut it off the unplug the ICP to see if it would clear up the needles on the gauges did a full sweep as if i disconnected the battery which i though was weird.
View 14 Replies
I have Warn hubs that I have to lock in. All works good. A/C goes to defrost at first when cranking but then runs fine after a couple seconds. So, I was thinking that maybe my pump is running all the time. Who knows. I'm sure all my vacuum lines are dry rotted. What exactly is the need for it exactly and what's the best way to cap? Hoping to do it at the unit itself if possible.
View 6 Replies
I just recently purchased my 1999 ford F-250 superduty V8 5.4 5 speed with 144,00 miles and I'm having a issue with the clutch pedal sticking in and then it will pop out after a couple seconds. It will stick more when I come to a light and have my foot on the clutch but the pickup drives fine and there is no slipping of the clutch. I have never experienced this issue before in any rig I've owned. so I'm a little lost at the moment.
View 2 Replies
I own a 2000 Ford F-250 5.4 Automatic. It tows my 5th wheel trailer very good. On our last trip it suddenly experienced the "check engine light" effect.
The light turns on randomly and either goes of after a couple of seconds or it doesn't go on when I restart the engine.It is mainly annoying, but when in towing it really hurts, because the engine switches into an emergency mode and stalls.
I read that the engine uses only 4 cylinders. I read many articles on the web about that light, but I couldn't find a solution. The thing is I brought the car to several repair shops but none read a code from the computer.
I think it's not a real fault but a misreading or maybe a cable that's grounding? The problem is, I can't bring the car to a repair shop, because there is nothing wrong with the car. How can I find the source of the problem?
View 14 Replies
I had the engine out of my truck (7.3 with e4od) to do manifolds. Anyway, I got it back in and started it up. Since there was air in th fuel lines it had to crank a couple seconds but started up. I looked and now fluid coming out, then it sat for a few minutes running and I took it for a drive. While sitting in the driveway it wa smoking a bit. But I thought it's from the oil I got in the exhaust while drilling two of the manifold bolts and soaking the bolts with ATF/acetone. After about half a mile I thought that maybe it's more oil then that would cause... So I went back. I looked and the inside of the exhaust is covered with oil, and the rear of the engine is also.
When it was out I capped all of the open ports so I could pressure wash the grease off. Also, I flipped the CCV so I could do the delete. During instal, I missed the cap on the CCV and it was not able to breath. I think that maybe it built up pressure and blew the valve cover gasket? It looks like it's coming from the right cover on the backside; I had not taken this cover off while the engine was out. How much pressure does it build? Is it possible that it could have blown the gasket out? I have done the oil cap trick to test blowby and it always passed the test. What it could be? For the leak on the engine and why it's in the exhaust?
View 13 Replies
Need better understanding of the wiring and turn signal selector than I do in my 07 6.0 HD. At first the issue started with the right front and right mirror blinking fast indicating a burnt out rear right turn signal. However after a few seconds the right rear will start working and the speed would be normal. I noticed it worse on very wet days making me think the rear tail light was letting in water and messing with the bulb. But it turns out it does it on nice days too.
These days it has evolved into the turn signal sometimes taking a few seconds before any of the right side actually starts to flash, also sometimes the indicator does not automatically deactivate after a right turn.
Giving the bottom of the steering column a calibrated tap usually always fixes the issue until the next turn.
Assuming its a bad turn signal selector switch Part number YL3T-13K359-ABJAEA but not knowing the wiring diagram I dont see how this bad switch would intermittently stop controlling the right rear turn signal. I would guess that it would tell the flasher left or right, not which lefts and which rights.
View 3 Replies
I have now replaced hpop, injectors, cups, gpr, batteries, uvch on both sides, icp and ipr on my 2002 F550 and it still has a long crank to start.
It has been driven about 1,000 miles since then and no change. I have no codes except buzz test produced a high to low 1272 1274 1276 1278 one time. Cannot get that to happen again.
It is taking 4 seconds of cranking to start consistently hot or cold. It always starts but cranks for what seems like too long compared to my other 7.3s. I have included a screenshot of the data and am curious on what everyone's thoughts are as I am out of things to look at!
View 14 Replies
My rearmost drive shaft u-joint is bad and has slop. I've been having vibration for about 7-8 months, but just started hearing a noise within the past week, especially when taking off with a load on the drive line (uphill or heavy acceleration). The vibration has not gotten worse, just that the noise has just begun to show itself.
I have one u-joint which is OE and has 275K miles on it, and it seems to be OK at the moment. The other two (including the rearmost unit) both have about 100K miles, as does the center support bearing.
Just because I don't want to worry about anything, I'm going to replace all three u-joints with Moog Super Strength units, and will also replace the Center Bearing with a new Spicer unit... just because I can and don't want to be pecked to death with multiple failures in the same drive line. I ordered the Moog joints because the only Spicer joints I could find were for the 4wd configuration.
That's the context... here's my question... The parts are on order and won't get here for several days. I've been driving the truck like it is at about 1500 miles monthly. Do I continue to drive the truck for another week before getting the joints and bearing installed? I know it's a guess... just looking for more perspective.
View 14 Replies
Still having issues with the transmission on my 05 F350. I posted before that it would take a few seconds to go into drive or reverse. The fixes were to change filters and do hot flush. I had the dealer do a hot flush, and then I put about 1000 miles on it. That didn't seem to fix anything, so I went back in and asked for more info. They did not change the filters. I thought they did, but found out they did not after the fact, so I decided to change the filters myself.
The interior filter was easy to change. The fluid was clean, and the magnet had shavings on it but nothing that seemed extraordinary. The exterior filter is impossible to get off. I reviewed posts on here before trying, so first was the impact wrench, then the pipe wrench, then the pipe wrench with a block wedged in to keep the thing from bending, still no luck. The cast nut broke off well before the pipe wrench came out of the drawer. How to get that thing off. I read on here somewhere that no fluid goes through that until 180 degrees, is that correct?
Scanguage says it rarely goes over 160, except for last evening when I was stuck in traffic. It went to 187, with ECT at 208. During this period, traveling under 40 most of the time, the transmission was shifting erratically, to the point I wanted to pull over and allow it to cool down. But traffic broke free, speed went up, and temps went down. Shifting returned to normal, except when trying to engage drive or reverse. The 3-4 second delay persists at any temp, and there doesn't seem to be any slippage. Just delayed and sometimes hard engagements. I'm at a loss for whats wrong.
View 1 Replies
I've just bought a used 2002 Explorer Sport Trac (Automatic) 120k+ odo and what I've noticed whenever I shift from Park to Reverse or to Drive it takes about 3 seconds before I feel a slight jerk moving forward before I can step on the accelerator for the vehicle to move backwards or forwards but if I step on the accelerator right after shifting to any gear except Neutral it won't run immediately as if the clutch is disengaged and after about 3 seconds it will suddenly engage. Is this normal or is there something wrong with the transmission?
View 3 Replies
B1602 PATS Recieved Invalid FMT/Key CD
P0753 Shift Solenoid A Electrical
P0758 Shift Solenoid B Electrical
P0740 Torque Converter Clutch Fault
P1760 Pressure Control Solenoid A Short
p0305 Cylinder 5 misfire Detected
P0316 Engine misfire Detected on Startup
The Trans will unlock while driving for a few seconds then lock back up and drive fine, it seems to be worse over the past couple days. It is no different cold or hot. I also noticed the head lights dim and the voltage on my scanner drops to around 12 volts when the trans disengages. When it is not acting up it drives and shifts perfect.
I have checked a few grounds that were visible and cleaned battery connections. The misfire code has been fixed, not related.
View 12 Replies
My passat doesn't have any leaks the coolant is at the max level, but when I drive the car for a couple of miles the temperature starts to go up the normal level. if I continue to drive the car it goes to the read level. If I stop the car an let it cool for 20 minutes I can drive the car, but I will start to overheat, but if i accelerate fast the temperature would start to come down, but then after a while it will overheat again. Some times it will drive at normal temperatures levels for a long time and then it will slowly start to overheat, if i step on the gas when i park and the temperature levels are in read the needle of the temperature will start to go to normal levels but if i drive the car then it will start to overheat the car has 80000 miles ...
View 4 Replies
I have an interesting automatic transmission problem. Hot or cold makes NO difference. When the car is started, put in reverse it will work perfectly 100% of the time. When the car is started, put in Drive the transmission will slip for about 5-10 seconds before working perfectly. When the car is started, if you wait 3-5 minutes, then put it in Drive it will work perfectly.
View 13 Replies
