Ford - Explorer :: 2005 - O/D Light Flashing With Check Trans Message
May 14, 2013
05 Ford explorer O/D light flashes along with check transmission. Iv had it at ford and they checked it for codes and said it needed a new torque converter, and valve body torque plate. They changed the torque plate, cleaned the valve body changed the fluid and filter, checked it again for codes and said it was fixed. less than 100 miles and 1400 dollars later with a new torque converter new torque plate and fresh fluid and filter still have the same problem. What else could be wrong with this transmission It drives and shifts as it should and it has from the start of the o/d light flashing and the check transmission message.
View 4 Replies
Advertisement
Wife's truck- 2002 v8 limited explorer with 116k... Yesterday she calls and says the od light is flashing and the message center says check transmission. She drove it home then when I got home the light was off and all seemed ok. I am taking it to have the codes read and hoping that my mechanics scanner picks up a code.
View 2 Replies
O/D light was blinking and "check trans" message was on display. I brought in for service and they changed trans fluid & filter. I have to take back to service center because now tranny is slipping. I would like to have some information before going back. It was not doing this before service. It is OK on highway for most part, happens more when starting out. Also has shut off a few times while sitting at a light. It didn't do any of this before service. What would cause this? Could it be the wrong fluid or not enough added?
View 1 Replies
My 1996 X with the 4.0 has developed a flare from 2-3, and the O/D light flashes. It still drives well, but it's bothersome, to say the least.
I'm hunting a replacement tranny, and am wanting to know which year X's to look at as a donor.
View 6 Replies
Check Charging System message, battery-shaped idiot light, and audible beep has happened a few times over the past month or so. Yesterday it happened while my wife was driving so I had to bring it to the dealer, not to mention I drove it last night and there was constant beeping for about a minute which was pretty annoying.
But first I had the battery checked, which turned out to be OK. Also we got a new alternator 5 months ago, installed by the dealer.
Today they said they "updated the computer" whatever that means, and otherwise couldn't find anything wrong. $99.85 plus tax.
Needless to say I'm not confident that "updating the computer" has fixed it. What are the odds we get the warning again in a couple of weeks? Short of disconnecting the sensor, is there anything that can be done?
View 2 Replies
Three weeks ago I replaced my battery and serpentine belt as general maintenance before heading out on a prolonged trip. The next day I started receiving 'check charging system' whenever I turned the a/c on and the truck is at idle. Power steering becomes very hard to turn and engine feels like it is going to quit.
This is not a problem at highway speeds. Looking at the engine when the a/c is engaged, a slow down of the belt/pulley is obvious. The alternator has been removed and checked, battery checked good, and the belt is the right size/length. What could be causing this? Again it started behaving like this after a belt and battery change. There is no issue if the a/c is off...
View 12 Replies
It's a 2002 explorer, 4.0, 5R55W trans, all was fine then O/D light starts flashing, so I limp it home. Trans isn't slipping, every gear works, it does kinda bang into 4th but is otherwise normal. Took it to auto zone to have the code read, but no codes found. Disconnected battery to see if it just needed a reset maybe, let it sit for a few hours, reconnect, OD light still flashes. Borrow a different OBD2 tester, still shows no codes, still drives the same just bangs into 4th. I've read up on the solenoid pack replacement, just kind hesitant as I feel like I'm guessing at the problem and might be throwing money away.
View 2 Replies
This issue has only happened twice to me.
I go out to start the car, it cranks and cranks and cranks. I stop turning the key. I then try again and it hesitates to starts. I give it a little gas and it starts. When it does this, the car begins running very rough and idling rough. When I give it a little gas while it's parked, the check engine light begins flashing at me.
I turned the car off and came back to it the next morning (maybe 10 hours apart). It started right up no problem, no CEL either.
View 2 Replies
I have a 2003 GX470 with 174,000 miles. It continues to be a great vehicle.
Recently my air conditioning system only blows warm air in both the front and rear. When I start the vehicle, the Navigation screen flashes the message "Check Air Conditioner", then the A/C button on the Climate screen flashes.
I have searched the forums and read every post regarding this issue, and it seems that one possible fix is the "magnetic clutch relay", but the link to Sewel Lexus lists this part as belonging to the ES330, and NOT the GX470. There is NO such part listed for the GX470 on that website.
One other post suggested that the author pull the AC error codes, but I don't know how to do that on the GX470.
View 9 Replies
I have a 98 Ranger, 4.0 automatic 4x4...I just replaced the upper and lower intake gaskets and after fumbling with the pug wires to finally get them in the right order, I suddenly find my OD light flashing off and on, and the tranny slamming into second, and once in top gear can feel the OD popping in and out? From my reading here it looks like a pretty common problem, but the solution isn't as clear...
The vehicle set for about 3 months while I healed up from a injury, and and was working just fine when I parked it...due to the blown lower intake gasket. I am thinking I have a vacuum line not connected or wrongly connected...or some kind of over looked item, but I can't spot anything...should I get a code reader and go from there...
View 14 Replies
OK....my gas cap (5.4 gasser) wasn't put on properly at the gas station. A couple of blocks later, the "Check Gas Cap" notice came on. I stopped a few blocks later, and installed the cap properly. The notice STILL came on. After messing with the cap 4 more times, I gave up, but the notice is still on. Do I need to have it "erased" like a code, or is there a problem with the cap? Everything LOOKS fine...
View 2 Replies
I have a 94 E350 with a 7.3 diesel. I took it to the Ford dealership to have a new fuel filter and oil change when I got it back the OD light was flashing and transmission shifting hard. They tell me they cannot find a problem could they have possibly knock a wire off of something to make this happen...
View 3 Replies
My 05 SD started to flash tow haul mode and check gauges message came on while I was towing my car hauler trans temp gauge quit working then check engine light came on too truck runs fine disconnected batteries then re connect them ( trailer now disconnected) problem solved for about 3 mi of driving then it came back w/o trailer I'm thinking rusty trailer ball on hitch caused this maybe not a good ground for trailer tow computer? What kind of scanner etc do I need to possibly clear this problem out? I am the original owner never seen this happen with this or any other trailer I've towed.
View 3 Replies
Just recently purchased a 2004 Eddie Bauer Explorer w/ 110k. Took a Snap On scanner with me to look at it. ABS light was on and I also get a 4x4 high flashing light every 2-3 minutes. Blinks 8 times then goes away. Scanner showed the RF speed sensor isn't sending any mph signal back. Just reads 0. Will my problem be a new sensor or is the sensor getting a dirty signal trying to read dirty teeth on the hub? Also, will fixing this stop out with the blinking 4x4 light?
View 1 Replies
I've got a 2005 Touareg V-8, 17,200 miles. I've got the xenon lights and the problem is as follows. I started getting the "Check Lights" message on the MFI. I checked the lights and everything was on and working. I took the car for service and had the dealer check it out. Of course the dealer couldn't find anything.
They checked for fault codes and didn't find anything. Once I left the dealership the message came back on so I turned around and went back to the dealer. I left the car on so that the fault codes would not clear. They instantly hooked the car up to there test equipment and found the fault code, the code indicated that the problem was in the left head light assembly circuit shown as B+ as the problem.
Since then they've replaced, the headlight assembly, the control module, the wiring harness and still today I've got the same "check Lights" thing going on. When the Check lights message comes on I loose my left light all together, the problem is getting worse and they don't seem to be able to find the problem.
View 6 Replies
I have an early 1999 Ford F350 4x4 7.3. I purchased it used about a year ago. The trans was replaced with an ATS 4R100 and a billet torque converter. I have the paperwork for it to confirm it along with the mileage when it was installed. It currently has about 35k on the new trans.
Several months ago the trans heated up to about 200 degrees on my trans temp gauge that was already installed when I purchased it. Not a huge deal and after pulled over and high idling it off I went and no problems.
About a month ago I was towing my fifth wheel when I noticed the temp rising on a level grade. I also noticed the OD light flashing. I made it home and when I went to drive it the next day light was not flashing and it shifted and drove like normal without the trailer.
I towed the trailer again and same thing, OD light flashing and started heating up. I changed all the fluid and flushed it based on the trans flush procedure I got in this forum and replaced with an OEM trans filter. Towed the next day and everything was good. Temp was good and no OD light flashing but I lost 4th gear. All other gears shifted fine, no slipping, just won't go into 4th.
On my way back home the OD light started flashing again and instantly the heat started rising on the trans again. I was finally able to get it into 4th if I let off a little, but as soon as the OD light started flashing I lost it again.
I have a friend of a friend who works for Ford who offered to come over to hook his scanner up. When he hooked it up there was no stored codes from the OD light which we both thought was odd. Took it for a test drive and the OD light started flashing so we could get some readings. He said it showed an error shifting from 1 to 2 and another error when shifting from 3 to 4. I unfortunately forgot to ask him for the specific codes. He tried to read the torque converter info but said my truck was to old and the PID was not supported to read that info.
He said it appeared it was mechanical but without some type of break out box where he can physically shift the gears he couldn't say for sure if it was mechanical or electrical. He did not seem to interested in doing that test for me as he rebuilds trans on the side and said he could rebuild it for me.
It seems my overheating takes place when the OD light starts flashing. It still drives fine and shifts smooth with no issues with or without the OD light flashing. 4th gear usually doesn't work but on a rare occasion it will go into 4th fine which makes me believe it may be electrical.
I am new to diesels but have learned a lot about my 7.3 lately. I recently installed injectors, up pipes, hutch mod, and several other little things so I can get things done myself but am just a DIY'er who can follow good directions. I know very little to nothing about transmissions though.
While working on another issue I did notice there is a large wiring harness that connects up on the driver side of the trans. I unplugged it and was checking the wires and after removing the dirt and crud on it you could see the outside wire sheathing had deteriorated exposing the copper. I bought some liquid electrical tape and sealed everything up. I did look for a replacement wire harness at the time and the one I ordered was very similar but the plug was different so that is why I used the liquid tape at the time. I did not seem to have a problem at the time after fixing it but wanted to mention it here in case that may be an issue.
I also thought swapping out the solenoid pack may fix it. I did not want to drop the trans and send it for a rebuild if I did not need to. I know there are some other sensors associated with the trans like the TSS I think but don't know if they are even related to my issue.
I tried getting the codes from the guy but he does not have them and I can't get him back out. I have an OBDlink device connected to Torque on my phone but I couldn't get it to read trans codes. Could be user error.
View 10 Replies
Well I went about 20mi to pickup a door for my inlaws. Get about a mile from home and my tow haul light is flashing. Truck starts shifting strange then I smell it trans fluid. If course I get stopped by a red light shut it down. Started and had to rev to get it to move now four houses away from home coast into the drive shut it off and trans fluid is covering the entire bottom of my truck. Even the rear tires inside are covered. I had the wife crank it and I blew a trans line near the ext. trans oil filter. What are the chances that I did not toast my trans? No prior shifting or slipping problems before this mishap.
View 14 Replies
I have a 2006 6.0. It's hard to put into to drive and for you to get it moving you have to just about floor it. The tow haul light is flashing but my bullydog won't pull the codes. It stops moving after like 30 to 40 ft after you got it moving and acts like it's in natural. If you turn it off and back on it sometimes will move another 30 to 40 ft sometimes. It also sometimes if you put it in reverse won't let you give it gas. Like you can push the pedal but the rpms won't climb for this reason I'm thinking something to with a solenoid or fuse or something along those lines and also because if you restart it will move again. I don't know much about transmission. I'm taking it to a shop tomorrow for them to try and read the codes. If they say the transmission is toast i already located another one 2 hours away to swap in which I'll do myself to avoid the high cost of the shop which also I'll look to yall for guidance. I drained some of the transmission fluid and didn't see any metal flakes. Should I pull the pan as well and look if nothing is coming out in the trans fluid ?
View 4 Replies
2000 powerstroke 4r100 transmission. It has 155k just had it rebuilt and the shop is having a night as am I. It was shifting hard and the o/d off light would start flashing after you drove it a while. Its still doing the same thing and the shop checked the whole wiring harness and replaced the accumulator twice believing they got a bad re-manufactured one. The only code I can pull is a 605 pcm read only memory error. Could the cause be a bad pcm? The shop doesn't seem to have a clue at this point and I'm out 2500. IV taken it back twice now and Iv driven it a total of 35 miles since the rebuild...
View 1 Replies
Any reason why the OD light flashes, and how to fix it with out spending an arm and a leg?
Light flashing on a 99 ford Explorer.
View 3 Replies
Recently my check engine light came on. I understand this isnt such a big deal, but then my engine started "skipping", and my overdrive light is now flashing. my car will stall if i come to a complete stop without putting it into park or nuetral. I dont know what to do.
View 7 Replies
