Ford F-150 - 1997-2003 :: 1998 - Leaking Exhaust Manifold
Nov 24, 2015
I have a 98 F150 4x4 Super Cab 4.6 auto that has a leaking exhaust manifold. I changed both manifolds about 3 years ago and the passenger side bank is leaking again. I haven't gotten into yet to see if its just the gasket or the manifold itself. My question is does anyone know of a set of headers I can put on the truck that will bolt up to the existing exhaust? If I make the switch to headers I don't want to have to redo the whole exhaust system.
View 3 Replies
Advertisement
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 Replies
I had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
View 14 Replies
I am changing the passenfer side exhaust manifold on my '00 150. The bolts all came out fairly easy, sprayed them often in PB over the last 2 days, my problem is the 2nd and 3rd nuts on the bottom are under the motor mount. Do I need to remove that or is there an easier way that I'm missing.
View 11 Replies
So I think I have possible manifold leak in my exhaust and its because when the engine is super cold, and I do have a straight pipe, but it sounds like a tractor... until it warms up after few minutes, it goes away.
My exhaust manifolds are rusted to crap and stuff is falling off, paint or whatever there was on them.
Now I've looked at bunch of videos on UT to get a better understanding since everyone says the nuts and studs are hard to remove or snap.
Now my question to anyone who's done this in their garage; I've seen bunch of videos where the stud snaps flush, then he takes a nut, puts it over the hole, holds it up with needle pliers and uses a MIG to start welding it... stud to nut... then puts a wrench and off it goes.
Now, I'm not a pro welder or anything so is it possible to by accident weld the stud, nut into the head and then never ever be able to undo or take either one out?? or is the head or whatever made from different material that won't get welded to the nut or the stud??
View 8 Replies
Leaking exhaust manifold? The truck has a much louder than normal "knock" when accelerating. At first I thought and had some bad fuel in the tank. I eliminated that with a full take of good fuel and some STP but the "knocking" continued. Then I thought that perhaps it wasn't firing on all cylinders but it felt like it had full power. I took it to my mechanic and he said it as a exhaust manifold leak. He said that he has never replaced the exhaust manifold but that it was a "nightmare" and expensive. He also said that it's not a safety issue but on the long run the leak would cause the truck not to pass its emission test. He said the problem was with rusted bolts that would be difficult to remove.
View 12 Replies
I have a 1999 ford f150 4.6 engine and it has an exhaust leak but wondering what is the procedure to remove a broken bolt and the rest of the bolts on the manifold
View 2 Replies
2003 F150 5.4 4x4 supercrew ,76k miles
Recently the passenger side exhaust manifold cracked on my truck. I bought this truck about two years ago with 58k on it and currently have 76k miles. I remember getting the carfax report and being relieved to see that it had exhaust manifold replaced in July of 2014 at 49K miles along with a new EGR tube. I called the shop that worked on the truck to see if he could confirm that both manifolds were replaced since carfax only said manifold & egr tube. The shop manager confirmed that both manifolds were replaced and he told me that they were most likely manifolds from napa according to the part number.
Now, my question is, what's the best brand to replace the manifolds with? Should I just go with OEM and spend the extra $130 per side? I know the manifolds are a common problem with these trucks but only lasting three years and 27K miles just seems ridiculous to me.
I'm hoping that when I get around to actually doing this that they wont be to bad because of how recently they were replaced. For now I just cleaned the area with a wire wheel and used the inferno metal repair. Seems to have done the job but I don't expect it to last long, just another month or two until I move to a place where I can actually work on my vehicles.
View 1 Replies
Truck Specs: 1997 F250 LD 184000 miles and a 5.4, automatic, shift on the fly 4x4 extended cab.
What I did: Changed the exhaust manifold gasket on the right side. There were some broken studs which came out with a stud remover.. No torch was used during this evolution.
What happened: After driving 10-15 miles it set the codes that I listed in the subject line. Reset the codes 20 or so miles later the P1131 code set again. (both times there was a noticeable loss of engine power) The upper O2 sensor checked out with a meter. When I checked the voltage on the truck's harness plug referenced to the NEG terminal on the battery, both the power and gnd had 12V- Key On Engine Not Running (KOENR).
What I did: Cleaned the connections put dielectric grease in the connections and reassembled. Reset codes; all was well ~ 100 Miles later the codes are back. I also ran a continuity check from the plug to the control module, they check out fine.
View 1 Replies
I was looking at my exhaust manifold..and I found a couple of studs missing...so if I want to replace both of them , is it better if I replace all of them on both sides of the engine ?
By the way..my exhaust manifold is good I don't think none of the studs are broken.. but I have been having this engine knocking noise on my engine, do yall think a couple of studs could be the problem of why my engine is knocking?
View 2 Replies
If the exhaust manifold gasket is broke / cracked will it making a ticking sound?
View 5 Replies
I have a 97 f350 crew cab xl stock everything. 351 windsor in it I do believe. as of right now He is broken down pulled apart in my garage. Due to a much requested headgasket replacement. In any event long story short I got him all apart to discover that there was someone in it before me & had broken the infamous exhaust manifold bolts (5) and two of the lower intake bolts, (of course I've tried the correct route in removing these broken bolts/studs but again the year of the truck (1997) & its bone stock no way their moving...
So of course I tried the next best thing (on a budget) which is to drill them out, but I went to far into the exhaust manifold bolt holes, And now I believe that I've ruined the heads is this so? If so who knows where i can get a decent set of bolt on heads ready to go. yes this is my daily driver & since He's been down I've been going deeper in dept.
View 1 Replies
I have a 2000 with a 5.4 and 166K miles. It had multiple exhaust manifold studs broken on both sides. Now that thay is fixed, I am getting the p1131 and p1151 codes. The EGR tube was also replaced at the time of the manifold fix. I checked over all the tubes and electrical connectors to rule out something simple but did not find anything out of place. The intake manifold was replaced with a new Napa one less than 5K miles ago as well.
Could the leaky exhaust manifolds over time set the fuel trim level high and now that they are fixed, the ECM is thinking it is running too rich? Can the ECM be reset to zero? There is also a ticking/rattling noise when you accelerate that seems to be coming from the fuel injectors. I listened with the stethescope and they are the only things that sound like the noise I hear. Could these all be related?
View 5 Replies
I have a 95 4wd f250 with a 351w my manifold gaskets are leaking I was wondering if when I that the time to remove the manifolds and probably be drilling and tapping should I go with headers if I should where can I get a very cheap set I'm on a budget...
View 1 Replies
2005 Supercrew and my passenger side exhaust manifold was leaking. Son of a mother duck that was a joke to get removed. Front two studs broke off about 1/4" below the surface. Manifold is not cracked but putting a straight edge across it's out of plane at least a quarter inch.
Had planned on the dorman manifold but read some poor reviews about it cracking in less than a year and being warped out of the box. There is an ATP manifold with very few reviews but all good. Or just bite the bullet and do shorty headers? The driver's side looks a lot easier to access.
These trucks really weren't designed to be worked on after assembly were they? I had to invent new cuss words. Looks like Ford manifold is disco'd...
View 3 Replies
Light did not come on for a while then it finally did. I replaced all plugs & that did nothing, almost made it worse. Put a scanner on it & it reads bank one lean, misfire. i unplugged all the coils one at a time on the drivers side & didn't notice any drop in rpms. On a side note, the exhaust leaks a bit of water out of the tailpipes a bit at idle.
View 3 Replies
I have a 98 f150 4.6 4x4 with 175.000 miles, I suspected the intake gasket is leaking, I'v never done this before. What is involved with this type of repair? Will the intake gasket leak bad enough to leak antifreeze on the floor? Is it okay to continue to drive with this problem? Bad weather is on the way.
View 7 Replies
I have a 2005 f250 5.4 no mods. its got 120k and needs a wake up. the passengers side exhaust manifold is leaking to the point of fixing and would like to get some input before the big purchase. my question is, headers or new manifold, and what brands is preferred for both I really don't prefer one or the other i just want the best fix really. Changing coil pack and getting more performance out of them and if so what brand. I would like a boost in lower end acceleration and throttle response, like a programmer or such. and if so what brand once again.
View 10 Replies
Whats the best way to get at the driver side exhaust manifold? I have a leak and its tough to get at. Should I remove the tire and inner wheel well?
View 1 Replies
I have been told by the AC shop that my AC manifold is leaking. I have a f150 1997. When they say manifold do they mean both the suction and high pressure lines? In pictures it looks like the AC manifold includes all the lines to the compressor.
View 1 Replies
I've currently have 114,000 miles on this Pontiac Bonneville and I replaced the intake manifold last summer. Recently, I have been having issues with the intake manifold leaking a fluid on the right side of it (facing the engine) and been having dirt or some other type of fluid mixing in my fluid tank. The leak has been causing some smoking issues. Also, when I start the car in the morning white smoke comes out of the back of it. Where I need to start so that I can get this fixed. I'm assuming something went wrong in the replacement.
View 6 Replies
