Ford F-150 - 1997-2003 :: 1998 V8 - Misfire / Hesitation When Go To Accelerate
Sep 1, 2014
I have a 1998 f150 w/ the 4.6L V8
For months I have had a hesitation in this truck when i go to accelerate, and at times you can even feel a little buck with the cruise set at 70MPH. It has gotten worse and worse. When i start pulling a trailer good luck, it will do it but its terrible, hesitations and misfiring,
There is always a misfire/hesitation. Will Idle nice After its warmed up. Sat for 2 weeks fired it up and it had a HORRIBLE idle for at least 1-2 min. This is new now it wont idle when cold. Now I had one code Cylinder 4 misfire, cleared the code never came back 2-3k miles later still not back on -
replaced coil packs
New plugs
New wires
Fuel pressure test good
Checked the Heater hose - not leaking and nothing in the hole.
View 3 Replies
Advertisement
So my truck started to intermittently misfire about a month ago . I changed the spark plugs wires at first and it seemed to get better but it still had a misfire . I replaced the spark plugs and ignition coils and the misfire is still there . Up until the other day it was a noticeable issue but still drivable with . On my way home from work it got alot worse and started to misfire any time I tried to accelerate and now is noticeable at idle now as well.
I checked the fuel injectors resistance and they are about 14.8 ohms . I am not getting any codes for a misfire . I tried to pull the fuel injector connectors to try to find the source of the misfire but could noticeable change in engine rpm. Where to go from here and what I should check first? Would a clogged fuel filter cause something like this ?
View 9 Replies
I have a 2001 f150 5.4 with 200,900 miles. Just bought the truck about six months ago off my dad when he got a new one. I am now experiencing what seems to be a slight misfire. With the hood up pulling the throttle around 2200 rpm starts making a loud knock. Above that rpm nothing and below that nothing. Standing by the tailpipe it sounds like a small backfire. It Idles really rough and when you get that sound out of the tailpipe it jumps like its hiccuping. And tailpipe is vibrating quite a bit.
Things I have done in the past month include replacing the pcv valve, changing spark plugs, cleaning throttle body, cleaning MAF, took down exhaust to check cats because i was experiencing a power loss and bogging. When the exhaust was off i punched the two rear cats. I ran a bottle of iso heat in the gas. Everything seems to have supported the power problem but now less than a week later i am starting to experience the knock and backfire type sounds.
View 14 Replies
Just bought a 1998 5.4l F-150 Lariat. 136,000 miles.
Question about the overdrive button on trans handle. When I push the button, I don't see any light turn on (or off) and I don't feel any change in the gear ratio or increase/decrease in rpm's. I assume since the button in there marked "overdrive" that the vehicle in fact was equipped with it. Could it be a bad button, fuse, or ?
Also, it just started the shudder/hesitation at certain speeds that I see a lot on these threads. Seems like that is a coil issue as the description in many threads is exactly what I am experiencing to incl the rotten egg/fuel odor. However, it started the same day (not same time, later same day) I decided to push the overdrive button while checking out all the things on the truck.
View 1 Replies
I will add as many details as possible :
2000 f150 4x4 offroad package
5.4L with 131k on it
new Dorman intake manifold
new Global Automotive (Ebay) COPs
New Motorcraft spark plugs
About 1500 miles ago I started throwing a code signifying a cylinder 3 misfire. The truck would bog down real bad and then after 5-6 seconds of no power it would return to normal. I tried replacing the COP (both with new and then with one from another cylinder) and plugs but no resolution. So I talked to the local ford service manager and he said it sounded like intake manifold problems.
Replaced the intake manifold and no more codes were being thrown.
1500 miles later and today the truck started having a hesitation/shudder when I was sitting in a drive-thru. I put the truck in neutral and park and neither solved the issue. With the earlier issue, when I would put in neutral and increased rpm, the issue would resolve.
I pulled out of the drive-thru and the hesitation was consistent no matter what the rpm or speed. The truck feels almost sluggish and lacks power. The hesitation is like 2x/second. When accelerating its almost like the rpms and speed hesitate, jump, hesitate, jump.
View 12 Replies
I have a 1998 F150 4.6 that has a misfire with no CEL. I have already tried the following: checked fuel pressure, change cam shaft sensors, changed coil, checked MAf seems ok, spark plugs and wires. On my scan tool it wont show any misfires when obviously its misfiring. When driving it will run good for about 10 seconds and then misses for about 10 seconds and it just keep going in this loop.
View 8 Replies
Ford F150 1999 5.4 XLT... I've had this truck since may 2013 from the 2nd owner who only drove it
occasionally to make sure it ran. For the last 5 weeks there have been two occasions where my service engine light appeared...once on 12/28/15 and again today. Both read cylinder 4 misfire. Upon searching this piece which I'm assuming is the boot that covers or houses the spark plug is very unsecure and causes a shaking feeling as I accelerate or idle. Being so far back I can't reach it with extensions on a ratchet and barely fit my hand back there. Having to consider taking it into a shop for further analysis and repair but I'm trying to save as much money as possible as I am in between jobs since mid January. I have a picture attached...
View 4 Replies
After/during the rain, every other time my truck loses considerable power to accelerate. It's not consistent but happens increasingly often. As I accelerate up to ~ 50km/h (also when I reverse), my engine will shake the entire truck. Past 50 it "appears" to go away. Typically this will last up to 10 mins and will disappear and run fine again. The last time it happened the check engine light came on and went away the next day. After reading online, I've heard about the "COP" connection??
2003 Ford F-150, 4.6L Triton V8 XL, 2WD
View 4 Replies
I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.
View 14 Replies
P0306 (ok #6 missfire) with P0171 & P0174 --- Do I chase electrical or fuel or both. Afraid to assume anything but probably would normally address the misfire electrical first.... Don't want to go down that 'primrose path' if others have been there first!
View 4 Replies
Ok I've been plagued with this very random misfire/power loss/hesitation problem going on a couple of months. You could drive the truck anywhere from 50-300 miles without having an encounter of this problem. It seems to do it now mostly on contiguous long trips over like 30 miles. It one time threw up a P1131 code which quickly went away on it's own. This is a list of stuff that has been recently changed: plugs, wires, coil packs, air filter, pcv valve, fuel injectors, tps, idle air valve, MAF cleaned, fuel filter, and egr valve.
I sprayed with brake cleaner for vacuum leaks around the intake tonight after driving a continuous 50 mile round trip it messed a few times on the way back. When I sprayed the EGR valve mounting area it idled rough when it was hit with brake clean and idled up. So there's a leak there. Or is it stuck? It will be driving normal and usually when you come to a stop the engine will start missing really bad and then when you take off there's no power at all. You keep your foot on the gas and eventually it will feel like all the power is just turned on.
If it does it while you're driving highway speeds it will feel like you've lost a cylinder but it's not as dramatic as when you come to a stop and it starts missing. I can't be 100% but I don't think the EGR wasn't leaking before I replaced it and it was still doing the same thing. I'm wondering why the Check Engine Light won't pick up an obvious misfire when you can you actually feel it. And why if it was the vacuum leak would it only start doing it after many miles of driving?
View 11 Replies
I have hesitation as I accelerate especially starting from a stop. It will continue until cruising speed. Funny thing is when I put the cruse control on the hesitation stops and it runs fine. If I want to accelerate while on cruse the hesitation starts again until I let off the accelerator. Is it the TPS ? I changed it two months ago.
View 8 Replies
Finally registered on this site after hearing good things from others who are currently on here. Been a 6.0 PSD owner since buying the truck since new in 2003-F250 CCSB. I have done regular maintenance on it and have had a good run until recently. Everything is stock on the motor and currently has 229 000 miles.
I will describe my current problem: I have borrowed my brother's tablet and have the following numbers from the Torque pro app. While trying to accelerate it now has a hesitation and seems to not have the power.
At idle: 630 psi HPOP, 24 % IPR, 47 volts FICM, ICP volts .1
Trying to accelerate on at highway speeds: 1230 psi HPOP, 83% IPR, 47 volts FICM, ICP volts 2.6
Also, sometimes when starting the truck it seems to rev extra high for a split second. My brother says I may have a high pressure leak on the system. What I should check first?
View 14 Replies
I have a 2003 Toyota Tundra V6. The problem I have with it is it hesitates. It does not happen ALL the time but it is very frequent. Sometimes it happens when I try to accelerate from a dead stop and other times while I am driving along (does not matter what speed). It will usually hesitate for a few seconds then everything is normal. The check engine light thus not come on.
I took it into Toyota. They duplicated the problem on the first test drive but did not have their equipment hooked up at the time. They kept the truck for over a week and finally got it to happen again. I guess they must have only been going on short test drives because it happens to me multiple times a day. They told me it was the throttle body and it needed to be replaced. My jaw hit the floor when they told me how much they charge to replace it. I ran this by a couple of friends who work on cars on the side and they said it sounded like the mass air flow sensor needed to be replaced. Since this was much cheaper than a throttle body, I replaced that. However, it did not solve the problem.
View 2 Replies
2003 Ford F150 XLT - Truck hesitates (or bucks) as the throttle is pressed. Not from a stop though. It starts / runs fine, but no matter how how fast, what gear, hot or cold, it feels like the fuel cuts out for 1/2 second. Also it is not a specific point in the throttle motion. It does it when it is halfway, 3/4 or fully depressed, but is not consistent. It does happen more frequently now than two weeks ago. I am not getting a check engine light.
4.6L V8, 5 Speed Manual 4x4, 74000 mi
View 14 Replies
Recently purchased a 2000 ford f150 4.2l. started hesitating when i would try to accelerated stressed or when a.c on. if i drive it like a grandpa wont do it. filled up the gas tank and it completely went away. the second it went down to the 3/4 line, started hesitating again. mind you when it was full even with the a.c on and going 80mph on expressway it would not hesitate.
View 2 Replies
97 f150 4.6 4x4, no check engine light, no missing or sputtering, however when I try to get going I can't get passed 2500 rpm and when it finally does its still kind of sluggish and can't pass as easy. Changed fuel filter. It idles fine and when I put it in neutral it will go up to 5000 rpm if I want.
View 6 Replies
I have a 2003 screw 4x2 with the 4.6, 148,000 miles, and I'm not sure what kind of transmission. Recently when the truck would shift into second it would hesitate and I would feel a slight grind, but it only did it when it would shift at 2000 rpm, if it shifted at 2500 rpm it would shift fine. I checked the fluid level, it was full, it smelled okay, looked *fine.
After pulling a boat (19 foot bass boat...nothing too heavy) it started to shake violently when I'd take off from a red light. So I dropped the pan and changed the filter, The fluid was dark red and smelled a little burnt. I put 4qts of fluid in it along with some Lucas transmission fix. The shake during take off is gone, and the grinding while shifting into second got a lot better but didn't go away completely.
However, now the grinding into second has has gotten worse again, and if I make a right turn from a red light it grinds and feels like its slipping until it shifts. I am not sure why making a right turn would affect it but its definitely worse when i turn right, left turns are fine. I'm guessing my transmission is going out and I just need to get it rebuilt...
View 3 Replies
I have a 2001 F150with the V6 motor, automatic transmission and 73k miles. It has begun having hesitation/missing problems at low rpm, 1000-1800 or so, and it feels like the engine shuts off for a fraction of a second. At idle and above that range it seems to run fine. Also, it only happens in Drive and when the engine is fully warned up - it does not do it when cold or in Neutral. Uphill, downhill, doesn't matter. There are no OBD codes. The spark plugs, air filter and MAF sensor have been replaced recently. I have OBD scantool on my laptop, but have not been able to use it yet.
View 1 Replies
I have a 03 F150 with a bi-fuel 5.4 engine an it has 195000 miles. I have had trouble for some time now with misfires. I bought the truck in october of 2011 with 125000 miles and replaced all the coils and spark plugs because it was misfiring badly will running on CNG. It was fine on gasoline and never had any codes. After I replaced the plugs and coils it ran fine on CNG and gasoline.
This summer 2013 it began missing badly at highway speeds only when running on CNG. If I accelerated the miss would go away until I was light on the throttle again.I checked the misfire count and found the bad cylinder and replaced a coil. Then a day later same thing on another cylinder. I swapped a coil from another cylinder and problem went away for a day. Eventually I chased the misfire around all the cylinders on the engine until I had ended up either replacing a spark plug or swapping a coil on all the cylinders. And I still had a misfire. It seemed to be worse on days with temperatures above 90 degrees. Eventually I got it to stop misfiring.
So now 5 months later I am back again with a misfire. This time it is misfiring on both gasoline and CNG and under any throttle conditions, except coasting. I have no codes. And the misfire monitor is sending me around the engine again. I have replaced a spark plug in two cylinders and swapped 4 coils.
I'm ready to buy all new coils, but I want to be sure that it is not a waste of money since the old ones only have 70000 miles on them.
Two days ago I had the misfire monitor saying #4 in the evening and the next day without me having done any work on it it was saying #6. Later that same day it said #7 and I still hadn't done anything other than drive the truck.
I checked the connections at the firewall on the drivers side with the three large plugs that are held in with a 10mm bolt, they looked fine, no corrosion or burnt pins. I checked the connection at the ACFM which also looks good. I will check the connection at the PCM in the next day or so.
Some other problems that may be contributing:
1. I occasionally get a U1262 code (scp fault)
2. Sometimes when I check the misfire monitor it only shows 7 cylinders, sometime 9 cylinders. I am using an Innova 3160 scanner.
3. I have either a leaking valve cover gasket or leaking head gasket, because I have oil dripping from the rear bottom corner of the passenger side cylinder head right above the exhaust pipe.
View 5 Replies
My speedometer has not been working for months now and it really hasn't bothered me as I go by RPMs, but I am going to make a long trip in a few weeks and I wanted to try to get this fixed.
The speedometer flips over to 100 mph and rest on the opposite side as it should. When I accelerate it does not move until I get over about 35 mph where it will then flip to 86 mph. It will slowly move to 82 mph as I accelerate up until 75, where it will then no longer change. Every once in a while it will start working when I start the truck up, or when I am driving down the road. It has before, within a 30 minute time frame, started working and stopped working 6 times. Currently my ABS light is on, but it has been on long before this started occurring. Every other gauge on my dash works.
I drive a 5 speed manual V6 2003 Ford F150.
View 6 Replies
