Ford F-150 - 1997-2003 :: 1999 - Brake Lines Diagram?
Apr 10, 2014
I have a 1999 Ford F-150 4X4 w/4.6L V8 W code, I recently lost all brakes. The primary line from Master Cylinder to ABS Pump rusted out completely. Replaced them but the other lines from ABS Pump to wheels are looking real bad. So I need to replace them, however I have no idea what the routing system looks like. Looking for a 97-03 F-150 Brake Line Diagram? I live at the jersey shore... so yeah rust is extremely common.... unfortunately.Also, where to get line assemblies?
View 7 Replies
Advertisement
Blew a hole in the 3/16 inch line to the rear on the left frame rail, behind the gas tank. Lost all brake function.
Got the truck home and inspected. The line was rusted bad about 6 ft long from the connection at the rear hose to the axle, up to the rear seat area ( crew cab). From the drivers seat forward, the line looks very good. The line across the rear axle from left to right looks very good. I bought two 50 inch standard lines 3/16 inch. Started at the rear hose connection 6 inches behind the gas tank and ran forward to the rear seat area.
Cut about 32 inches of the other 51 inch line and connected and ran forward to below the front seat area. There is a metric connector at this point. I cut an inch in front of it to eliminate it. NAPA sells a high psi compression fitting ( steel , 10,000#) that you can connect two 3/16 inch lines together. I did that under the drivers foot area. I have done two different 2002 F150s in the last year due to this failure. Something to look into. Not nice to loose brakes in traffic.
If your worried about the steel compression fitting, don't. I have used these on several cars and trucks over the last 15 years. Make sure you get the STEEL high pressure compression fitting. Total line replaced on CREW cab, 51 + 32 inches. Pops right back into the original plastic clamps.... I might mention, that is where the failure was, under the plastic clamp at the rear end of the gas tank area.......... crud must collect on the clamp.
View 5 Replies
I just bought a 2000 Excursion limited v10 4x4. I'm going camping this weekend so trying to install my brake controller. I found the plug but noticed these wires dangling. I can't see the back of the harness. I'm afraid the PO may have cut them to install a universal harness. How to recognize them? I don't want to buy a ford specific harness if the wiring has been cut.
View 3 Replies
What kind of brake line is it and if is replicable with regular brake line? I'm just replacing long line between front and back splitter block and just would like to know what is it. What is purpose of that braiding (?) at front brake lines and why they wind down instead of going straight. Part of that long line is braided too, part that go across frame.
View 3 Replies
What happens if or when you get air in your brake lines and the air gets into your ABS pump/module? What are the symptoms? Anything other than a soft pedal? My ABS module keeps thinking one of my tires is sliding when i am driving and pulses my pedal and i am at a loss.
View 14 Replies
I have a 99 5.4L V8 Triton engine. The power steering is not working. Need a full power steering diagram including components and hoses/lines? I have attached a picture of a broken line which I think might be for the power steering but I'm not sure. What this (?) line is in the attached picture or have a diagram?
View 3 Replies
Working on putting this project back together and cant find my notes when I pulled it apart last year. Any schematic or picture of their brake lines from the master cylinder to the rabs or front brakes? Better yet, which port on the master cylinder goes to what axle?
View 9 Replies
Got a 2002 7.3 f550 and the other morning it wouldn't go into high idle. Noticed my parking brake light was off. Messed with the switch and eventually jumped straight from the connector to ground... still no light. The light does illuminate with key on. I have tested the fuses. Where do I go from here? Looking for a wiring diagram....
View 14 Replies
So here's the background. I recently bought this truck. It's a 97 Ford f150 4x4 4.6l 99w vin code. Anyway Driving it home got a p0401. No problem. I Applied vacuum from other vacuum source to EGR engine stalls. So to me passages are clean in the throttle body. I checked to verify and indeed passages are clean. No while doing so I noticed no vacuum was making its way to the dose valve thing. Strange.... So took the line that runs to the passenger fender to dose off and it was impossible to blow air through.
So I cut out the clogged section found solder in the line. I filled the gap I now created using some 5/32 vacuum line reconnected to test and to my anvil still not vacuum. So I disconnected it again. Went directly to where the yellow/orange dose vacuum line connects to at the passenger fender and to my surprise no vacuum there either. No my question is. Am i suppose to have constant vacuum to the dpse or I'm I just being an idiot. And two if I am suppose to when the vacuum line runs into the passange fender where does it go from there and could I have a major issue in my hands?
View 1 Replies
Looking for a diagram for the ecm pinouts for a 2000 5.4 4x4 f150? Im mostly trying to find the TCC for the tranny.
View 1 Replies
I just bought an 01 F150 and previous owner didn't have the manual.
Need a copy of the fuse box diagram for this truck?
I've been surfing the net, and can't find what looks like the right one.
View 10 Replies
Got myself a brand new old truck. No radio and all the wires had been cut. I just printed of a wiring diagram from web and went to work I am now on my second one and it has the same colors for two different speakers!! The first one was completely wrong. Looking for a good wiring diagram for a 97 f250 super cab.
View 1 Replies
Anyway, I'm gimped in my left shoulder for a while and I'm trying to do what i can with my 03 F150 Supercrew /4bt Cummins conversion. I am using a Dodge 47rh tranny and need to know the wiring for the 4R70W so I can hook up my 12 + ignition wire, back-up lights and neutral safety switch. I'd like to build my wiring harness.
View 6 Replies
I am having trouble big time getting air out of my brake lines. I put new front pads and rotors on and also had to replace the brake line coming from the caliper as it kind of crumbled and needed to replace the next line up that goes to the ABS block on the left front. After doing this, I bled that wheel only and at first it was ok until the brake line on the right front at the caliper also broke when I was pushing on the brake pedal with the truck running, spewing fluid all over. I have tried to bleed using a decent vacuum bleed setup from Advanced Auto but keep getting massive amounts of air coming out and when I start the truck and hit the brake pedal, it goes to the floor. Could the master cylinder be bad? I have checked every connection that I made and all other connections and there are no leaks at all. I am stuck in the garage! The truck is a 1999 F150 4x4 with 4 wheel ABS.
View 1 Replies
I have a '03 f 150 screw 4x4 with 5.4. I had to replace the heater core in the truck and I could hear air going through before the replacement. Now I can still hear it, have tried to burp the system a few times, even jacked up drivers side front on an incline to get reservoir higher. Ended up replacing the hose with the flow restrictor and that worked or so it seemed. The noise is back and I am lost on what to do next. I tested the head gasket and that came back negative also. What to do next or possibly what the issue is?
View 13 Replies
I am trying to add a keyless entry to the already equip, power door locks but am having problems figuring the wiring schematic
View 8 Replies
2002 4.6 SC with towing package... Transmission cooling lines to radiator leaking. Replacing them? How long does it take, can it be done while working on the ground? Any tricks or problems to look out for?
View 3 Replies
I have a 1997 4.2 and when i got it the big vacuum reservoir under the passenger fender had the lines broke off. Where these lines go or have a diagram...
View 1 Replies
I got a question, what is after ac hose vacuum left side on a 10 th gen 4.2l engine bay by the firewall, to the right of the blue thing, right of that on that line their is a 2 end diameter rubber vacuum line? What is that called, I need a replacement.
View 7 Replies
How to replace the 2 "drop down" rubber brake lines on a '13 250. They appear to be secured to the bracket that looks like is the bracket that's holding the DEF tank on. And by the quick look without much digging in appears as though I have to take the DEF tank out or significantly loosen it to get at them. I'm no neophyte when it comes to this stuff and will take the DEF tank out of necessity, was just wondering.
View 1 Replies
I plan on replacing the brake lines on our 1999 Ford F-250 Super Duty. The rear line blew out right by the hose, on the framerail. All five lines, all five hoses. What size lines? Looks like front two are 3/16", rear two over the axle are 3/16", and the rear line in the frame is 1/4".
We are removing the bed (2013 bed) to make things easier. I am thinking fuel lines and parking brake cable while the bed is off. I have stainless steel hoses from KLM performance and I am also planning on replacing the rear rubber hoses. Obviously I'm using nickel copper line. There shouldn't even be an option for other brake line.
[URL].....
View 5 Replies
