The Service Engine Soon light has come on on my 2000 F-150 with a 4.6L when I was driving home in the rain. It has about 120,000 miles on it now. What are some of the main reasons why this comes on? Oxygen Sensors?
View 14 RepliesI have a 2000 f150 with 198,000 miles. The lite on the dash came on, "service engine soon" , I had the codes read and they said the coils are going bad.
View 2 RepliesI installed a new alternator now the check engine light is on....
View 7 Replies2001 F150, 5.4L gas, 4wd, stock, 217k miles, auto trans. Bought it used about 4 years back.
Currently away from home base. Left Saturday for a 600+ mile trip. All fluid levels are good. Truck has been reliable. No major issues other than an alarm malfunction a while back which got sorted.
About 90 miles into the trip down the highway, the service engine light comes on. Hmm. At the next fuel stop I tanked up. Started and it was a bit rough the first few seconds and then settled. Seemed to have an engine noise I had not heard before.
Pulled over in the station and popped the hood. Oil good. Coolant fine. Power steering fine. Listening to it I could definitely hear an unusual sort of "ghost" like sound. Hard to describe. Sort of like a low "woooooo." It was low, but definitely there and not normal. Could be unrelated to the engine light. Pulling out of the station the sound varied and got louder with slight acceleration. Possibly beginning of an accessory bearing meltdown?
No acceleration or dying issues. Got back on the highway and kept on trucking for 600+ miles. No running issues. No shifting issues. Ghost noise not noticed at highway speeds.
The power steering pump is probably in need of replacement at this point with this mileage. It does drip slightly, but not a lot. It may be the original pump for all I know. Same with the water pump.
The alternator was replaced last year with a Bosch unit. I have never replaced the O2 sensors. Stock exhaust. Spark plugs were replaced a while back with Motorcraft platinums.
It is now Sunday night and I went out to listen for the sound, and it is not there anymore, but the service engine light is still on. First things to check with a truck that has 217k miles on it?
Was tempted to bring it to the dealer here, but it seems to be running ok in spite of the light coming on. So I may leave it until I get back home and check it more myself then. Can't do much here since I don't have my tools/service manuals etc with me.
I have a 1999 F-150 w/ 4.2 V6. and auto trans, truck has 219,000 miles on chassis but only 25,000 on engine and 10,000 on trans. I've been getting obd codes p0705 and p0715. I replaced the position sensor on outside of trans. but I continue to get the codes off and on again. I noticed that the O/D "OFF" light on the shift selector blinks simultaneously when the "service engine soon" light comes on. I've noticed that there is no low gear unless I have it in D from a dead stop, and not even when downshifting manually.
View 1 RepliesThe Service Engine Soon light is on in my 2001 F-150. I checked the code and got PO156 generic O2; circuit (bank 2, sensor 2). What are the most common things I should look at? The truck appears to be running fine, no driveability issues.
View 5 RepliesMy Service Engine Soon light came on early last week and I got the code P0442- Evaporative Emission: System leak detected (small leak).
What are the most probable things I should look at?
I have a 2002 f150 4.2 code p0340, ran rough, replaced cam sensor. drove after replacing and it runs fine now, code and service engine light comes on after restarting. from what i have read could this be a wiring problem?
View 4 Replies2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
Last week my service engine light came on. Friend checked it with his code reader. Got a P0402 code insufficient flow EGR valve. I have read several different threads on this subject on another Ford truck forum, slightly confusing me. Should I trust the code and just replace the EGR valve or do a number of other things that
1. Clean the throttle body first?
2. Test the EGR valve by blanking it off?
3. Test the DPFE valve?
4. Replace the DPFE valve instead of the ERG valve since the EGR valve rarely goes bad?
5. Only get OEM parts since after market parts do not last?
Light came on a few days ago. 2000 exc with 7.3 diesel the mileage report said 155000. Took it to Autozone a hour ago and these are the codes: P0683, P0676 and P1670.
View 14 RepliesI have a little more detail on when the truck starts and does not . I have gone out the past two days and put the key in the ignition and turn it to the on position and all the lights come on except Service Engine Soon light and truck will not start. I bought a ceramic electric heater and placed it on the floor directing the heat under the dash. after ten to fifteen minutes I go out and put the key in the ignition turn the key to the on position and the service engine soon light is on and the truck starts right up. I let it warm up for about a half hour and then shut it off. I then try to start it right back up and the service engine soon light comes on momentarily then goes off and the truck does not start?
View 5 RepliesMy trucks symptoms include a illuminated service engine soon light, sometimes a high rpm idle, and sometimes a rough erratic idle. When a scan was done it indicated the oxygen sensor was defective. The issue is: which specific one (there are multiple oxygen sensors) or how could I check or determine the faulty one for sure. I am trying to economize and replace only the bad one myself if possible. I own a good multimeter, can it determine the bad one? 1999 F-150 4.2 Litre V6 oxygen sensor dillemna....
View 7 RepliesI have a 2000 - F150xlt - 4.2L - V6:
Today while leaving work for lunch I started the engine and suddenly the ABS light came on and the engine cut out before I put it in gear. Then as I was driving each time it cut out the ABS light came on. So I stopped at the convenience store across the street from work to get some gas thinking it was low although it had a 1/4 tank. But after filling up it would not start. Then relay #2 began clicking in the fuse panel and would not stop whether the key was on or off. Several minutes of this went on and then I pressed the brake peddle in once more and everything on the dash lighted up, the dials fluttered around, the clock came back on, etc...
So I tried starting the engine again and suddenly everything started working and the engine started up. I drove it home and it ran fine with no issues, no cutting out or anything. After lunch I tried it again to head back to work and the truck would not start again. But this time there was no clicking from relay #2. Everything was dead until I pumped the brake peddle several times with the key off and then turned key in the ignition and then it started right up and drove like normal. Why it's doing this and what to check to fix it?
I have a 2000 f150 4x2 5.4 168k... Check engine came on,started shaking, weather was really cold. RPM would be a little high then low then back up. Especially when I turned on heater. Felt like truck would die but never does nor does it have issue starting.
So far, I have replaced two oxygen sensors inside engine,all coils, spark plugs, fuel filter, had injectors cleaned, intake cleaned. Truck runs better but, light came on a day later again. I can feel the tiniest of shaking going on and, cold mornings still make RPMS a little unstable. I was driving truck on highway at about 60 mph when a slight tug was felt and Truck check engine came on. I feel truck heavy, once it warms up completely, a little lighter.
Codes came up at auto zone as P1151
But I'm running out of options and frankly, money to fix this truck.
Checked the MAF and looked okay.
I'm with minimal skills.
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
2000 Buick Century Custom with 140K miles: Service Engine Light came on. Re;placed gas cap, light still on. Took to dealer who replaced HO2 sensor, light still on. Took to dealer who found no problem but charged $100 for looking. Light still on. Took to dealer who said it needed two major parts. Light still on. Took to another mechanic who could find nothing wrong. Light still on. Is there hope?
View 8 RepliesI just purchased a 2000 Nissan Maxima GXE with 219,000 miles. I've had it less than two weeks, and the Service Engine Soon light just came on. I live somewhere that requires emissions testing in order to register the vehicle. My temporary plate will expire soon, so I need to get the car to pass emissions.
This is my first Japanese car and first non-American vehicle. I didn't know until after I had given the check to the guy selling the car that he used premium gas. He said that Nissan recommends it. I've never driven a car that required premium gas before and wasn't keen on the idea since here, it is 40¢ a gallon more expensive than regular unleaded.
I spoke with my landlord about it, as he is a certified Honda mechanic. He told me to first try getting half a tank of regular unleaded and putting it in with some fuel injector cleaner. He said if I didn't notice any decrease in performance or knocks, to then just add a bottle of of fuel injector cleaner to every other tank of gas.
I got a half tank of regular unleaded with a bottle of fuel injector cleaner and didn't have any issues. I then filled the tank with regular without any fuel injector cleaner. I used about ¾ of that tank when the service engine soon light came on. I took the car to Valvoline to get the codes read, and while they couldn't give me any code numbers, they said it was something to do with emissions.
Here are my questions:
Is it possible the light came on because I switched from premium to regular unleaded or perhaps because I would need to add fuel injector cleaner to every tank of gas I get and not every other tank as my landlord said he does with his car?
Should I try either adding fuel injector cleaner to every tank of gas or just switch back to premium? If I try either of those, and one of those was the problem, how long would it take for the Service Engine Soon light to turn off?
I just bought a 2000 Saturn SC2 that had a "service engine soon" light on. I took it to the shop to get it inspected and they reset the computer and said that I needed to drive it around 100 miles to reset the computer so it would pass MO state emissions. After driving it 160 miles only two of the required have reset. I took it on the highway at 55 MPH steady for 2 miles. Actually did around 8 miles. as the shop suggested and that did not work.
View 3 RepliesI'm trying to get my 2000 Regal to pass inspection, but every time I have it serviced and need to drive it for approx. 100 miles before the emmissions test, the service engine soon light comes back on. Can a bad gas module in the gas tank be the culprit? My gas gauge has not worked for several years and it didn't cause the service light to come on before, but the mechanic said that is the only 'code' that comes up on diagnostics.
View 8 RepliesI have a manual 2000 Nissan Sentra with 101,000 miles. The Service Engine Soon light stays on. I was told it was an vacuum leak or mass air flow or basically the mixture of oxygen is off. (I already had one mass air flow put in a few years ago.) I have been ignoring the message. We went camping and drove twice to 9,000 feet. No problems on road at all. The car runs great. In fact we got 35 mpg on the trip. Am I possibly hurting the car by ignoring the message?
View 5 Replies