Ford F-150 - 1997-2003 :: Codes P0304 And P0316 - Lean Bank 1 And 2
Jul 5, 2017
2003 F150 v6 2wd 170k ... For a year I've only had codes P0171 and P0174 (lean bank 1 and 2). I was told it wouldn't hurt anything... I think now I should have taken care of it.
Anyway 3 weeks ago my truck started running a little rough. It was sputtering and had trouble getting up to speed, sometimes also the air switches from vent to defrost until switch gears and rpms go down. It gradually got a lot worse over 10 days while part was otw. A week ago i changed MAF and cleaned the black thing it's inside of. It started running better but still not good. I pulled my small trailer 2 days ago and it got worse after dropping the trailer.
Today checked codes at AZ and lean codes are gone and have p0304 (#4 misfire) and p0316 (crank sensor problem). Is this related.? Also Right before all the trouble I changed battery and alternator. Also i read online that MAF needed 2 weeks to relearn the way I drive to get correct gas/air ratio? Is that correct?
Also I read so many different things I needed to do during installation... Some say I need to turn key to the on position after unplugging old MAF then plug new one in... turn key to on position 10 times, Rev up engine, drive it rough for the first 2 minutes... etc. Is there a correct way to do it or is it vehicle specific?
Should I start by changing spark plugs and coils? The guy i bought it from and trust said he changed spark plugs right before I bought it. Will it ruin truck if I drive it? I've read so much but everyone says so much different things on the same topic. I'd what to start with or if this is related.
View 14 Replies
Advertisement
I've been having this problem since I've gotten the truck about year ago. it has very high long-term fuel trims and it seems no matter what I do I cannot get them to go down my fuel trims at idle are 39 Bank1 and 33 bank2 they go down to around 12>7 while driving what could this mean. And even weirder occasionally I get Bank 1 or bank 2 too lean codes at idle when cold starting???? 1997 Ford F150 4.6 ......
View 7 Replies
My 2003 ford ranger 3.0 v6 is having a misfire on start up and it is located in the forth cylinder. Where to start to get rid of this problem. i have already changed all my plugs wires and even the coil pack cleaned out the maf and looked for possible leaks. the car shakes really bad at lights and the check engine light starts to flash. Need diagram of where all the cylinder numbers are at and maybe the firing order?
View 14 Replies
Here are the codes I'm getting:
P0455 - large evap leak
P1451 - main control (evap canister)
P0306 - cylinder 6 misfire
P0174 - bank 2 lean
are these all related? Or two separate issues. I have replaced all the evap lines with new lines. I have a new egr valve, and exhaust manifolds, and what should I look at 1st
View 4 Replies
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
View 2 Replies
A couple of weeks ago I got a check engine light. Pulling the codes I saw that it was a p0304 and sometimes a p0316. The first time this happened I check the spark plug cables and one was loose (cycylinder 4). Then last week my fuel pump died. since then I have gotten the two codes on a somewhat continous basis. I replaced the plugs (needed to anyway) and the problem did not go away.
The odd thing is that the check engine light does not come on at idle. IT only comes on after the motor is at a higher rev. The replaced plugs looked pretty normal, but the cylinder 4 plug had some carbon deposits. I am currently running injector cleaner in the gas. I may go ahead and replace the plug wires since the current ones are high mileage and it is not an expensive fix.
View 1 Replies
What does this mean?? The o2 sensor(s) is reading lean?? 2001 F150 4x4 5.4
There was also an evaporator system code, but I think maybe someone left the gas cap loose? I unhooked the battery and it cleared everything. Truck started fine for a few tries. Will have it driven tomorrow to see if codes come back.
My reason for this is it was getting hard to start. I confirmed that fuel pump relay was not coming back on when cranking every time. Randomly it's fine, other times it won't start. Noticed it had CEL light, had it read at local Azone.
Don't know what to do about the "lean" issue? What would tell the pump relay to NOT turn on?
I removed the cover from the relay and inspected points, they were fine. Check with ohm meter=good. Watched it function without the cap on it. Would prime every time, but not come on when cranking every time.
View 8 Replies
Well I got the ubiquitous "Bank 1 Too Lean" code this morning. Yesterday I changed out the PVC Valve, Elbow and Hose assy.
I changed out the hose from the intake to the canister purge valve on the firewall next to the master brake cylinder, that one was like dust.
Today I'm changing out the rear O2 sensors, but I may change out the fronts when they get them in (very rural area hear).
I'll keep looking for vacuum leaks and change out the MAF sensor. I hate to think it may be the intake....
View 11 Replies
My truck is a 4x4 lariat, I've replaced both dpfe valve and egr, and the intake manifold gasket. Still getting the egr insufficient code. It went away from a few months after replacing the intake manifold gasket but has returned. Where do I go from here? I vacuum tested the egr and that's working fine. Should I buy ANOTHER DPFE valve? Where do I go from here I'm desperate.
View 14 Replies
I have a 2003 F150 V6 4.2L, 171,000 miles on it. I have four codes on it.
#p1518
#p0316
#p0303
#p0136
I had a p1518 in november of 2012, had it repaired and its back. In the time that I had it repaired and it came back on (maybe a month and a half ago) I only drove the truck maybe 3000 miles, if that. Just curious if this particular part should have some kind of warranty either by the MFG or dealer since the dealer repaired it. Have a limited budget, trying to find out what I can fix on my own in a timely manner.
View 4 Replies
I have a rough idle. I have replaced upstream o2 sensors, plugs, wires, fuel filter, dpfe sensor, cam sensor, and cam synchronizer. This has only moderately improved my problem. I still have the right bank, left bank too lean codes. Could it be something as simple but hard to find as a vacuum leak?
View 8 Replies
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 Replies
My 04 Explorer 4.0 has been giving me the bank 1&2 lean codes. It is the fully electronic throttle body not mechanical. It seems from reading that in 04 is when they switched to the electronic version. Here are some things I have done to resolve this. I created a diy smoke machine from a paint can and air. I found a leak by the egr.
I replaced the egr and gaskets, along with the metal part that goes into the throttle body. I replaced the pcv and hose(although it looked fine). I replaced my intake gaskets. I replaced the MAF sensor.
Before all of this my lt fuel trims were +25 for both bank 1 & 2. After doing all of this my trims did come down a little to Bank 1 +16 and bank 2 +23. I dont know what to check next!
View 4 Replies
So, my 2003 F150 4.6 that I just put back on the road after a four month break is running like crap. I took it off the road for the winter because it was missing (no codes) and didn't feel like dealing with it then but after running it for a day the CEL comes on. It shows the following:
P0304 - hoping it is a coil pack
P0456 - pending. Gas cap?
P0171 - pending. One bank too lean?
Does the 171 code possibly have to do with the misfire in Cylinder 4? I know it is impossible to tell yet but am hoping there is a potential connection.
Before I parked it in January, it was running a bit rough and stumbled on acceleration but never would show a code. Now all this. Going to change the coil first, tighten the gas cap, check for leaks and see what happens but is there anything common on these trucks that I should also be looking at?
View 7 Replies
I have been getting a P0171 and a P0174 code lean bank 1 and 2 sensor 2. I have replaced all 4 censers the 171 is gone but I keep getting the P0174 and it only comes on when I am on the highway after driving around 10 miles or so i got a freeze frame of the data when it happen.
View 6 Replies
1998 ranger 4.0L. I ran my scanner on my truck to day and my 2 bank 1 sensors seem to be bouncing between .150 and .700 but my bank 1 sensor 2 seems to be stuck at 680-720 and not bouncing, is this normal?
I did pull a code po135 heater circuit malfunction BANK 1 SENSOR 1 ...
Also I am not sure where my fuel trims should be...
My
ST1 10.0
LT1 25.0
ST2 12.0
LT2 25.0
closed loop.
When I first got the truck I pulled codes for lean bank 1 and 2 also a cylinder #4 misfire and the bank 1 sensor 1 heater circuit. I reset the codes and the heater circuit bank 1 sensor 1 popped the mil light in 5 min. So I am starting with the o2 sensors. I've not found any vacuum leaks at this point.
View 3 Replies
What would be causing my left and right bank lean codes? Truck still seems to run fine. I have also been getting number 6 misfire. all within the past week. I know Its due for a tune up but would a simple tune up fix these codes. Also besides plugs and primary fluids what else should I be changing. I don't want to be getting to involved just the main stuff.
View 5 Replies
Just put a cold air intake on my 99 f150 with a 4.6. its a CAI with a 4" tube and its not an oiled filter. there is NO vacuum leaks, the mass air flow sensor is clean. I am getting the codes 171 and 174 now and i know its from the intake because that's when it started running lean. Is there any way or anything i can adjust to fix this other than buying a 300 dollar programmer?? If I take it to a ford mechanic will he be able to fix this?
View 11 Replies
Explorer 2003 - 116 mi V8... Has been idling poorly at about 750 / 800 rpm never stalls in idle.
Check Engine Light came on - Read code said Too Lean Fuel Bank 1
Reset codes. After a couple hundred miles Check Engine Light
Once again Check Engine Light
Same error code Too Lean Fuel Bank 1
View 1 Replies
I am in the process of trying to chase down a vacuum leak on my 2003 F150 with the 5.4. I have checked all lines and cannot find it. I decided to check the long term fuel trim and noticed that my bank 1 is slightly higher than bank 2 (screenshot attached). Is this enough to assume the leak is on the bank 1 side?
View 14 Replies
2003 f150 supercrew with 166,000 miles on it. Daily driver. Service light randomly comes on and when code reader was put to it shows "left bank running lean." Will clear it and will randomly come back on. Truck seems to be running fine. No issues engine. Bad sensor? Or bad injector? Maybe way to test?
View 1 Replies
