Ford F-150 - 1997-2003 :: One Click Of Starter When Turn The Key - All Power Lost
Sep 27, 2016
I'm having some strange electrical issues b where to start fixing the problems. Here is whats happening:
- Put the key into the ignition and turn to the "on" position, full power to everything no issues at this point
- Turn the key to the start position, get 1 click out of the starter and then lose all power to everything
- Turn the key off and back to "on" position, sometimes I get power at this point and sometimes the power stays dead for a while
- Check the battery, which is good (12.3 volts)
- At one point someone noticed some sparks coming from a connector near the back of the firewall on the passenger side (sits on top of a metal cover with a large positive terminal right behind it). I've disconnected this terminal, cleaned it and put on some dielectric grease all of which hasn't done anything.
- Basically I mess around with few things, check some connectors, let it sit for a few minutes and then it will start.
View 5 Replies
Advertisement
My mom has a 2001 f150 with a 5.0. Had never had any problems with it till this week. She says it wont click or anything. When she tries to start it, the power door locks go to locking & unlocking. She said the battery is good. I figured probably the starter. She lives about 2 1/2 hours from me. I figured I would go down there and take the starter off and have it checked or rebuilt. Anybody ever had their power locks to go to moving when you try to start the truck. Also, when she turns the key on, her dash lights come on just like normal. Just won't turn over or click or anything.
View 3 Replies
Have a 97 Ford explorer. Over 270,000 miles on it. Recently had Crank sensor, Crank case vent tube, plugs wires replaced along with intake manifold gaskets. Also had fuel injectors cleaned out. Now i cant get it to turn over. Went to store, truck started fine, came out and click. Thought it might be the battery even though its also brand new but no, had the starter checked, it is also good. Put test light on all electrical having to do with starter and found all hot wires and good grounds. Finally bypassed the solenoid for starter and still nothing but a click. I also checked NSS to see if that might be it but after putting it in reverse, the reverse lights came on, and even jiggled shifter in park and neutral to see if that might work but still just a click. Not sure where to go from here short of buying all new parts but doesn't make much sense to do that if they all appear to be working properly. Don't have a volt meter to check voltage.
View 5 Replies
I got a 1997 f150 4x4 4.6L had to replace fuel rail after a couple holes were rubbed in it and caused a fire, but now after two weeks of it sitting at the dealer, I wasn't gonna pay for a fuel rail to be put on so i had it towed home and I did it, however now when I go to start it, it just clicks. So I have the battery tested and its bad so it was still warrantied so it now has a new battery and i also replaced the starter solenoid while i was at it. But still just a click when i try to start it. I had the starter out and bench tested it and it went but went slow and looked very old and tired, I am thinking i need a starter now because its a click from the starter, like its trying to go but isn't strong enough.
View 3 Replies
2001 F150 4.6 V8 Triton
Automatic
Battery Tests Good
Starter Tests Good - I saw it spin and come out at the testing station at Autozone
Ignition Relay (the one in the fusebox)- New (8mo.)
Switch on the firewall on passenger side of truck - New (8mo.)
Battery terminals/connectors - Tight, no movement, Cleaned within the last week.
Starter connections - cleaned within the last week.
I am having trouble with my truck not starting. The issue has been occurring on and off for over a year. Usually, it happens about once a month, regardless of weather.
I turn the key, and there is one click. Usually at this point, I can use one hand to gently pull the shifter "up" towards park and turn the key again and it will start. Recently it is not starting when I do this. I have tried many times, and have tried to start it in Neutral (is that even possible with an Automatic?).
With the key in the "ON" position, I go under the truck and jump the starter cellinoid. I am jumping the small post to the big post where th wire comes from the battery. I do not touch the post that the wire goes into the starter.
I am very confused because it starts just fine without fail and almost instantly when I jump the posts. It is drive-able this way, but I would like to resolve this issue, and resume using my key to start it since the issue doesn't seem to be resolving itself as it usually does.
A friend told me about the Ignition Starter Switch inside the Column. If I have time I will attempt to start the truck with a screw driver on the switch tonight to narrow down the issue.
View 9 Replies
Drove it last night around 9pm. Parked it and went to drive it again this morning around 7:30. No cold weather here or rain. Here is what I know: When I turn the key I hear a click (not a repeating click) but the engine doesn't turn over. Batteries have 12.5 volts. I put my trickle charger on them and had full charge after about 3 or 4 minutes. When I turn the key the headlights do not go dim. I put a screw driver across the solenoid on the passenger side fender and got a strong arc. When I do that, I can also hear another click that sounds like its coming from the engine. I tapped the starter a few times with a hammer, but it still wont turn over. I'm guessing bad starter.
View 14 Replies
I have a 99 f150 2wd v6 4.2 liter engine. Im going to sum up what happened and what I've done so far. One morning truck wouldnt start. Wouldn't crank, turn over, or even make a click click noise. I tried jumping it just to be sure but it didnt do anything. Battery is fine, interior lamps, displays, and radio all work fine.
I took the starter off, had it tested, it was bad so i got a new one. Still had the same problem. Finally, i got underneath the trunk and bridged the positive and negative on the starter solenoid and it fired right up. So the starter is not the problem.
Next I looked into the starter relay, if I bridged the positive and negative on the starter relay it fires right up just like the starter. But since that is only bypassing the starter relay, it didnt tell me whether the starter relay was good or bad. So I got a new starter relay and it worked! It started with the key with no problem 3 times! I thought the problem was fixed but when i tried to start it an hour later, nothing... Same problem as before.
I checked all my fuses, none were blown.
I'm under the assumption that either something leading to the starter relay is making the starter relay go bad OR there isn't enough power going to the starter relay. Maybe something in the ignition, even though my accessories are all still working.
It is the only vehicle I have to and from work. For now I am getting by with bridging positive and negative on the starter relay to start it but that is only a temporary fix.
View 8 Replies
I have a 2002 F-150 xlt 4x4 5.4l V8, 96k miles. been sitting about 3 weeks i went to start it and nothing.. thought ok jump. We tried jumping/charging the battery nothing. then we switched batteries from running car same thing when i turn key just hear a click in dash. battery light remained on even when we swapped out. The theft light was off as well.
View 1 Replies
I have 98 f150 with 4.6 starter went so I put a new one on wich was a hassle and it tries to turn but just wont as if the motor is seized. I had been hear a loud howling sound from what I think is the ac unit and the ac line burst after trying to start. Would a bearing or something with the AC be enough to stop the engine from turning over? Or could it maybe be a wire connection problem? To me it sounds like a starter trying to start a seized motor but I cant see that my motor would be out it only has 190 000km and the oil looks good. but we couldn't turn the motor over with a ratchet? The truck had been getting gutless. I am stuck...
View 4 Replies
I have a 1999 F150 Lariat 5.4 that's been sitting for a few weeks waiting for a new MAF. Finally got a MAF from a junkyard (out of an 01 Expedition) and installed it.
Turned the key, cranks once, then I hear a loud click and then just continuous clicking. I did some research and people are saying this is just the starter solenoid and that the battery may be dead. I charged the battery a couple hours and waited until it showed 11.some volts, tried to start it again, didn't even turn over, just clicking. I also noticed the theft light blinking rapidly, but if it were the PATS acting up, wouldn't the motor at least turnover?
So I went back to charging the battery. Went out a couple hours later (at night), and when I opened the door, none of the lights came on. Then I hear a click, the lights come on, followed by another click, and the lights went off. This happens each time I open and close the door. So did I potentially pop a fuse? Or is my battery just fried? Would replacing the MAF with the newer one out of the expedition cause any weird issue? I doubt it, but anything is possible at this point I guess.
View 10 Replies
Trying to track down an issue (annoyance) I'm having with my 02 7.3 4x4 excursion. When I get in the truck and turn the key (after waiting for glow plugs) the starter doesn't actually turn over for 1-3 seconds and sometimes up to 5. When the truck does turn over everything works perfect it's just an annoying delay.
View 13 Replies
I have an 02 f150 5.4 4x4, drowned it a while back, thought i had hydro lock, crank can be turned by hand though as far as i can with a wrench, so internals seem to be fine, no bent or broken rods that i could tell, ripped everything apart cleaned it up put it back together, new fuses, new ignition relay, new starter, alternator and battery as well, turned the key to on and got all my electronic stuff back up, turned to start and it all goes dark, which i assume is because at that point its sending power to the starter, but the starter didn't turn or crank the engine...
So question being when i put my new starter on is it possible that i might have crossed a wire or something that would cause it to not crank? and due to the fact that I had water in it, and had hydro locked it, all my plugs are out, now I know that spark is needed for the engine to run, but shouldn't be needed just for the crank to turn right? question being is that once i fix the wires on my starter, I am looking for initial crank before start up, so do i need to put a plug or two back in and hook them up to make it crank? or will it crank without them? and yes I did replace all my fluids as well.
View 8 Replies
After getting the oil changed in my 1997 Ford F-150 4.6L with 150K miles at a local quick lube, I made one stop and my truck wouldn't start. I could hear the starter engage the flywheel, but couldn't turn it over at all. Oil was clean and full. I bench tested the starter and it tests good. I put a breaker bar on the crankcase nut and I could barely move it. Oil level was about 2 quarts low before oil change.
View 10 Replies
Ok so I was looking at my blend door actuator motor to see if it was working. Just took off the bottom vent cover, turned key on and moved the air mixture to see if the motor worked. (it didn't) Then I went to start the truck and all I get is the solenoid on the firewall click each time I turn the key. I put a meter on the opposite side of solenoid and I see 12v across the solenoid. I can't image i did anything while playing around by the blend door actuator motor. I guess I'm looking for confirmation that the next logical step is starter and starter solenoid. Is there anything else I could be missing? is there anything else in that circuit between the solenoid on the firewall and the starter? I also cleaned the battery terminals and the terminals down on the starter solenoid. I also tapped the starter a bunch and put a charger on battery and tried jumping the truck too. Everything else works.
View 10 Replies
I have a 2001 supercab 4x4 with a 4.6 in it, it has 186k on it and the only issues I've had was a misfire not to long ago. I replaced the plugs and coil packs and fixed that issue. 2 days ago she ran fine with no issues and this morning I went out to go to the store and she wouldn't start. All the dash lights come on and all of that normal stuff when you turn the key. When I turn the key I hear what sounds kind of like a clunking noise towards the bottom of the windshield and the middle of the dash. The starter does not engage, no nothing, really confused here. I thought maybe the battery was bad so I put my jumper on it and tried but again nothing happened.
View 14 Replies
2001 6.8 Ex wouldn't start again today Get a loud click but starter doesn't turn over. Yesterday jumped it, took it to Advance where they checked battery and alternator; both checked out great. To start it this morning I ran my negative jumper from battery to engine block and it fired up It's about 12 degrees out and was same yesterday. Thinking dirty/bad ground somewhere ? Do I just start following the negative cable everywhere it goes or am I missing something here No garage and it is chilly.
View 3 Replies
I have an 02 F250 6.8 with 51,000 miles on it. I recently replaced the battery about a week ago, and only actually drove it yesterday for the first time since replacing the battery. I drove it about 25 miles, parked, and when I went to restart, it wouldn't. The starter doesn't crank, so I mean its not a cranking issue as in cranking, and not starting. It only clicks at the relay when turning the key. It acts like when you try to use a wrong chip coded key.
All of the dash lights came on, and I can hear the relay clicking, but that's it. I swapped the relays around, and no luck. If I let it sit a while, about an hour, it will fire right up. The battery cables are tight and free of corrosion. I am curious, since I just put in a new battery, could this be the culprit? Why will it start fine cold, but not hot? I have NEVER had an issue with this truck until now.
View 14 Replies
Ford F150 truck, when starting, the starter will turn over strongly for half a second then just abruptly makes a loud noise and stops. It won't ever fully crank. Is this just a bad starter?
View 2 Replies
I have a 2006 Santa Fe with 137K miles on it. Has been best car I ever owned, but have recently experienced a strange issue where it won't start, meaning I put the key in the ignition, turn it to the right and nothing, not even a click on the starter. I have found if I move the shifter around from P to R to D, etc. and then try it again it will start. Is there a safety interlock switch in the shifter that could be going bad and is therefore not satisfied/happy when I try to start the car? Or could the ignition hardware where I insert the key be the issue.
View 1 Replies
I have a '99 F-150 SC, 4x4, 4.6L, with 48,000 miles. I drove approximately 15 miles, then parked for 20 minutes. When I returned, the truck wouldn't do anything when the key was switched to start. It's as though there was no power going to the starter. Could it be a problem with the immobizer system, or just a freak incident with how I handled the key? The truck ended up starting after another 15 minutes and has consistantly started for the remainder of the day.
View 4 Replies
I have a 01 f250, I've only had it a couple of months. It has 300k miles on it and has its share of problems. I knew that going in and I just bought it for a work truck around the farm and honestly I don't expect it to work perfectly. But since I have had it there are times where it will not crank, it will only click under the dash and then a second click under the hood. It will do that in the mornings a lot and by the afternoon it will crank. I found that jumping the 2 larger wires on the starter solenoid bypasses the problem and it will turn over and crank. So I replaced the solenoid thinking that was the problem, but it still does the same thing. I know the batteries are good.
View 5 Replies
