Ford F-150 - 1997-2003 :: Popping Noise Coming From Both Sides Around The Wheel Area
Jun 13, 2015
Got a 1999 ford f150 2 wheel drive. I have replaced both upper and lower control arms with ball joints on both sides. New shocks, new stablelizer links, new inner and outer tie rod ends. Also, a new steering gear and i still have popping noise coming from both sides around the wheel area when i enter or leave out of drive ways, turning, or running in a hole. Doesn't do in going straight. I don't know what else to do. Driving me insane. I keep spending money on this truck and still where i first started.
View 9 Replies
Advertisement
So I just installed a fresh 4.6 long-block in my '98 4x4 xlt and I have a noise coming from the manifold area. Thought it was possibly valves or timing chain. Took it to dealer and they diagnosed it as the Intake Manifold Runner Control. Never heard of it!!! Problem is, I can't find that part for this motor. Is it inside the intake? Do I have to replace the whole intake? Dealer didn't tell me, once I said I would do the work myself.
View 3 Replies
Have a noise coming from the serpentine area. Sometimes it's a bit of a chirping, other times it's almost like a solid grind.
I pulled the belt off and the idler pulley had a bit of play so I replaced that. The tensioner pulley felt fine. I'm suspecting the fan clutch, as the noise only appears after the clutch has disengaged the fan (although it could be this is just masking the other noise because I've got a heavy duty / loud fan clutch setup).
How can I be sure that the fan clutch is the culprit before replacing it?
View 1 Replies
I have a 97 250 LD 5.4 that suddenly has a grinding noise coming from the area where the transmission and motor meet. I took the inspection plate off the transmission and can look up inside there and see everything moving. I use a screw driver and if I flex the plate that mounts between the transmission and the motor I am able to get the noise to quiet down until I release the screwdriver and then the plate flexes back and scrapes making the noise again.
I can not see where the plate is grinding when I look up inside there. I can't figure out how to fix this.... Why it would just start doing this on its own as none of the bolts on the housing have been removed except for the two bolts that hold the starter on. (Changed it a couple of weeks ago). Thought about loosening the bolts on the tranny housing but I'm afraid that it would open me up to further problems???
View 4 Replies
I blocked off the hpop discharge tube to test for leaks, shop air. I am plugged into the oil rail drivers side, and keep getting a slight popping sound. The first time I did this it took ten minutes to start, so I replaced the top injector seals. The second time it did this after about four minutes, so I took the oil rail to the local shop and they did the ball tube orings in the rail, now I went to put it back on and it does it almost right away.
Am I just pushing the oil out of the injectors? is this normal or should I have NO air noise period? I guess I am not sure how these injectors work, where does the oil go after it enters the top of the injector? It seems like it's coming more from the top coil area, more so perhaps than under the oil rail.
View 6 Replies
I just bought a 09 Corolla S a month ago. In the last few days I've been hearing a popping/knocking noise while I'm driving. It sounds like it is coming from one of the wheels but which one. It usually happens once I decelerate or driving at low speeds. If I brake the noise will stop. The rhythm of the noise doesn't seem to be consistent with speed I'm driving. It happens more often on bumpy roads but it still happens on smooth roads. I'm wondering what are the possible problems that are could cause this?
I don't know if this would relate to the sounds I mentioned but when I bought this car it had brake problems. It would grind pretty loud. The dealership ended up replacing new rear drums. So when I drove it home everything sounded good for about a week. The grinding noise came back and after I sprayed some brake cleaner it went away for a few days. I'm assuming thats what the dealership did to hide the noise. I went ahead and changed the front pads and that worked for a week or so...but the grinding noise is back. I was about to change my rotors this weekend when the popping/knocking sound I mentioned above started happening.
View 5 Replies
My friend has a 2000 f-150 2x2 and was following him and he said he heard something pop and then no transmission , haven't put a code reader on it yet. It's not the flex plate starer works fine fluid is a little discolored and has no bad burned smell to it.
View 1 Replies
Tonight I went out to get something out of my car, I had not driven the car in about 5 hrs. As I opened the back driver side door, I noticed a noise coming from the wheel well area. It was a quiet noise almost like a very quiet motor running, but it was very prevalent. I went to the passenger side back wheel and could hear it there also. I've never heard anything like this. Opened the trunk and listened for the noise but could not hear it there. After a few mins, I started the car and let it run, then shut it off and the noise disappeared. Only thing I could think of was a fuel pump malfunction?? I honestly don't know.
View 11 Replies
My 99 F250 has just recently started making a "rattling" noise. The noise sounds like its coming from the front left wheel area. The noise is constant while driving down the road, its NOT created by bumps or anything, its a constant noise while moving.
View 3 Replies
We have an 07 Prius with around 150,000 miles on it.
A couple of weeks ago I noticed a slight knocking noise coming from the passenger front wheel area mainly when I was turning toward the right.
Question.......So when turning to the right, it first seemed to me that the right side would experience a heavier load. However, after further thought and applying some physics the inertia of the car would actually be putting a heavier load on the left side during a right turn. Which is correct?
Just trying to troubleshoot the noise/problem.
#1 when I apply the brakes, the noise doesn't change. I don't think it's brake related.
#2 the noise speeds up with speed, meaning that it's rotational.
#3 The noise does get louder when I am turning right but has know progressed into a constant noise going straight. During a left turn it subsided.
#4 I did take my floor jake and jaked the pass. front wheel up but didn't see anything broken or damaged. I couldn't rotate the tire though.
#5 I also had the tires rotated today and the noise got worse.
View 8 Replies
2000 f150 supercab 4x4 offroad. Sometimes in a very strong wind, I get a lot of air noise around the doors which is up in the window area. I occasionally get it if I haven't got the back half door shut tight.
Just wondering if there is a way to puff up those door seals without replacing them? Inject them with something or use a hair dryer to heat them?
View 14 Replies
I have a 99 F150 4x4 4.6L automatic trans. The truck has 260,000 miles on it. Saturday, while going down the interstate, this chirping noise started up from the rear. When I got home I jacked the rear up and spun the wheels while listening. There is a chirping noise that, as best as I can tell is coming from around the front of the driveshaft around the u-joint area. I've never known of a u-joint to make this type of noise before. There is no vibration or anything, just the noise. The frequency of the noise increases and decreases as I speed up and slow down. I don't think it's coming from the transmission, but it's hard to tell, as everything echoes. I couldn't imaging the driveshaft itself making this noise, but I guess it's possible.
View 12 Replies
Lariat stepside, 5.4L with 150k miles. Loud popping noise, almost a clunk, when making a slow sharp turn. Put it on jackstands and did the normal tire grab and shake and found no issues there. Tie rods, ball joints and sway bar links all seem tight. Looked for signs of unusual rubber to metal and metal to metal wear and found nothing. The only thing I did see was the rubber boots on the upper control arm ball joints were split. What I have checked or if I am missing something?
View 9 Replies
The last couple of days I've noticed a metal clinking noise coming from the right front wheel area when I go over bumps. The best way I can describe it is what it sounds like when there's a loose washer and nut on a bolt. A metal on metal sort of thing. Tonight I was able to replicate the sound I heard by pounding on the tire and got it on video and posted it below. Watch in HD to hear the sound I'm referencing clearly.
[URL] .....
A couple of things to consider:
1. Just had spacers installed a few days ago
2. Also diagnosed the "clicking brake while turning slowly" issue. Thread about it here: [URL] .... Wondering if this has anything to do with the noise.
I have an appointment with Lexus tomorrow morning to have the brake clicking fixed under the TSB and several other issues addressed. Mostly rattles...
View 2 Replies
I've got sort of a howl going on, was thinking rear end, but when i jacked up the wheels and spun the driveshaft the noise seemed to come from the transfer case area. I haven't had a chance to check the fluid yet, could it be a bearing in the t-case? Its only when i'm on the gas if i let off its gone. 2001 f150 super crew 4x4
View 4 Replies
2000, F-150, 35K +original miles. 4.6L V8
Some weeks ago a noise started that sounded like fan blades striking against heavy plastic fan guard. At first I thought it was coming from the transmission/Transfer case area but after a few weeks of listening to I now believe it's coming from behind the dash area, however, I can't find any reason for it be from there.
The noise usually starts around 45 MPH
I checked the heater fan and it appears to be Okay. I don't know of any other fans in that area.
View 12 Replies
I have an '09 Camry and for the last few months have been hearing a metal popping sound in the rear wheel area when I go over a bump or pothole unevenly or backout of a driveway at an angle to go onto the street. The sound does not occur when the wheels when they are even, only when the rear right wheel is "lower" than the left. It has not been in any accidents and there was no event that preceded this popping.
I took it to the dealership but they were unable to replicate the issue but it happens no matter who drives the car (my husband or myself) and it is likely that the service guys didn't go over any bumps/curbs/potholes unevenly to hear the sound. What this is or if this is in need of getting fixed? They check the axles and said everything was good with the car but it is still popping and driving me nuts.
View 5 Replies
I have a 1991 toyota 4runner with 4wheel drive stick shift and it has been making a loud rrrrrrrrrrrr sound. It seemed like it was coming from the front right wheel or somewhere close to that area, so I checked the brake pads and rotor for rocks or any other object that might have gotten stuck. There was nothing stuck, however I did notice that the boots were ripped. So I changed both front axles and I also replaced the wheel bearing only from where the noise appears to be coming from. The noise is still there. It makes the noise sometimes, if i'm going slow or fast. Other than that, the car drives well.
View 2 Replies
2016 LTD Ultimate, 2700 miles. First and only Hyundai for the moment.
I've experience this one twice, a few weeks apart: cold start the car, and in the first 100 yards or so I'll hear a tapping noise that's clearly rotational, varies with speed but eventually ceases. Sounds like it's coming from front passenger wheel well area, and sounds like a stick or some sort of debris is stuck in the wheel. Both times I've inspected the area and found nothing whatsoever.
I live in an apartment complex area, park in a lot always in reverse so I'm always going from park to drive. The area I live in is wooded ("Pine Barrens" region of Long Island) but the roads are paved so it's not like I'm driving thru wilderness.
View 3 Replies
1997 Acura Cl 2.2 ... Ticking noise coming from the dash board and glove box area ( sounds like blinker ticking noise).
View 1 Replies
I have an '09 Camry and for the last few months have been hearing a metal popping sound in the rear wheel area when I go over a bump or pothole unevenly or backout of a driveway at an angle to go onto the street. The sound does not occur when the wheels when they are even, only when the rear right wheel is "lower" than the left. It has not been in any accidents and there was no event that preceded this popping. I took it to the dealership but they were unable to replicate the issue but it happens no matter who drives the car (my husband or myself) and it is likely that the service guys didn't go over any bumps/curbs/potholes unevenly to hear the sound. They check the axles and said everything was good with the car but it is still popping and driving me nuts.
Current suggestions:
• Cracked bearing race. It could be another problem entirely having to do with the suspension mounts or axle mounts but let's hope these new mechanics will figure it out.
• Problem with a wheel bearing
• Struts and suspension components
• Bushings and parts
• Loose upper strut center nut or from loose upper strut mounting nuts
I took it back to a shop but they are thinking the sound is actually coming from the body near the roofing area in the right rear portion of the car. They seem to think based on the sound (metal popping only when that wheel is lower (like coming out of a driveway angled, or going over a pothole)) that it is the metal body but it would cost and arm and a leg to get in to even find out what it was. They assured me that it wasn't impacting the safety of the body and is just a funky sound. The sound is much louder in the car than outside which I think kind of supports their theory. Are they right and it won't impact the safety?
View 4 Replies
