Ford F-150 (2004-2008) :: 2005 - Rough Shifts Occasionally?
Sep 1, 2016
I recently purchased a 2005 f-150 4x4 with 115,000 miles. The truck is in overall great shape but does have a mysterious transmission issue i have been chasing for over a month. The truck runs and drives great aside from a occasional rough shift. The overdrive light flashes and the monitor displays "trans fault". I have had the truck to a few different mechanics including the local Ford dealership. It pulls p0702. The truck will manually shift into 4x4 but it will not engage by using the switch. I have replaced: Trans wiring harness, checked all fuses, dropped pan and replaced all wires, nuetral safety switch and a few other misc. parts.
View 3 Replies
Advertisement
I have a 2005 5.4l f150. 105,000 miles. Recently While on a trip I experienced rough idle and stalling at idle. I drove it home 2hrs. The ride home was challenging. Poor acceleration, rough idle. Took it to the dealer and was told I needed plugs and I was 5qts low on oil! Not sure where the oil went. It hasn't been leaking and never seemed to burn oil in the past. They did the tune up. Picked up the truck. It ran fine while cold. Upon warming up it ran rough at idle and stalled just like it did before. Took it back, they said "you need a new engine. Upon warming the oil pressure drops indicating internal engine damage". I took it to a local guy he says replacing the cam phasers might fix it. What's the consensus, should I try the cam phasers? Look for some other potential problem or trust the dealer? (They did refund me for the tune up)...
View 14 Replies
2005 f-150 4.6l v8 rough idle only when truck is to normal operating temp. I have run several gas system cleaners through the truck. I replaced the air filter, the fuel filter and the spark plugs. I am only getting 14to 15 mpg mostly highway. No DTC's are showing up. The truck only has 50,000 miles.
View 6 Replies
I just purchased my first F150, 4.6L V8, 55,600 Miles. It intermittently has a rough idle and only seems to be when the engine is hot. I've had engine and tranny mechanics look it. The spark plugs have been inspected and are within an acceptable range. The throttle body has been cleaned. There are no trouble codes of any kind. What I can check next?
View 13 Replies
My 05 was running rough and misfiring quite frequently. After much deliberation, I took it in for a diagnostic hookup. The dealer said my driver side cat was clogged. Lucky for me, I was just under the warranty period(79673 miles). I have had it replaced and I can feel a noticeable difference in the way it runs. Could a clogged cat have made it run that poorly or am is it just in my head that it is running alot better?
View 7 Replies
A week and a half ago I went out to my truck to go somewhere and I got about 2 blocks away and the truck started running really rough and had a big lack of power, so I turned around and scanned it with my code reader and the codes I got were p2271, p2196, p0303, p0012, p2197, and p2272. since then I've changed all the spark plugs, boots, swapped all the coils and injectors from a great running truck, fuel filter, and the bank 1 upstream O2 sensor.
the other thing that came to mind that could of caused the problem is that a few days before the problem started. I jump started a co-workers car and he hooked the cables up backwards on his car. Could this be the cause of the problems I'm having.
The truck is an 05 F150 FX4 5.4 with 180,000 miles on it.
View 9 Replies
I have a 05 fx4 5.4L with 85k on it. It has started idling rough when i come to a stop light or slow down to 10 mph or less. It only does it once in a while. There doesn't seem to be any real pattern. The motor shakes until you rev it up and then it goes away.
I have cleaned the maf, put in new air filter and fuel filter. And put in a new battery. Would a coil act like that? Maybe plugs? Or a vacuum leak?
View 14 Replies
I changed the timing chain, phasers, tensioners, guides, and cam sensors and solenoids about 30k miles ago. Truck now has 170k miles. This past weekend engine started running so rough, it had the whole front end shaking. Threw 8 codes..1 bank..lean, bank 2 rich, timing retarded, cylinder G and F misfire, and more codes. It seems to have jumped timing pretty bad.
View 1 Replies
my f150 running right so i can enjoy it like everyone else does. I have a 2005 Ford f150 with a 5.4 auto.
It has a rough idle(shakes the truck), very little power, and poor gas mileage. Randomly It will throw a code for misfire on 1 and/or 3 on start up only. It does seem to perform better within the first few of starting but dies right off after that. In fact i got stuck in the snow the other day and it could barely break the tires loose to try and get it out (almost put in 4low cause i didn't want to hurt the trans). I have replaced:
Cats
Fuel pump
Plugs (motorcraft)
Random Coils
Did the timing chains and phasers
MAF
All new injectors
Intake gasket
Was at my mechanics and had a scanner on it and at idle the 1-4 cylinders are all show a negative cylinder contribution. But when you rev it up they all go to 0 across the board. Was kind of thinking about the Variable Timing solenoid.
View 1 Replies
I have a 2005 f150 5.4 3 valve with the p0012 code the truck runs good has a rough idle not sure if it is worth changing the vct or not the truck has 190000 miles....
View 1 Replies
I have a 2005 F-150XLT with the Triton 5.4L. The other day while driving on side roads (Paved, not back roads) I noticed my CEL on and it was blinking. There was a very rough idle as well as a big loss of power. When I pressed the gas pedal it was sluggish to say the least. I have yet to get a computer on it, since I had to order one. There is also a light gas smell, only smells near the rear of the truck. From what I am guessing, I think it is either a spark plur or a coil over pack, Truck has about 56K on it.
View 1 Replies
Getting these codes what they mean or need to do ..to get rid of them...p0022, p0171, p0174, p0183, p0340, p0300, p0316, p2006 did timing n plugs fuel filter n gas filter getting very bad gas mileage it runs good but here a ticking in motor at idle and more as u accelerate, running rough....
View 7 Replies
2005 f150 Lariat 4x4 5.4
Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.
After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.
The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.
View 3 Replies
I just locked out the cam phasers on a 2005 f150 with a 5.4. It now idles pretty rough. If I blip the throttle the revs will rise and then drop again, and it barely catches in time to prevent a stall. If I continue to tease it this way I can usually get it to stall. I'm getting no CELs or anything, but I intermittently will get a P035x code (it seemed to rove. I've gotten cylinder 1, 4, 6, but not consistently.). I have chased those around by swapping coils, checking/cleaning the connectors, etc.
I am kind of thinking that these codes are a symptom of my idle issues, and not the actual problem. What could I have done wrong? Could it be a vac issue? I had basically the entire ECU harness and all the vac lines disconnected to do the job, but as far as I can tell everything has been reconnected to the correct locations. I did have an SCT tune done to remove the phasers in the ECU. I installed it and still have the issue, so for now I am on the stock tune just to eliminate any variables.
Could my tune be the issue? Is this how you would expect the engine to behave with locked out phasers and no corresponding ECU tune?
View 1 Replies
My 2005 STX 4.6 fuel pump crashed a couple of months ago. A couple of days after having it replaced I started having hard/rough starting problems accompanied by a 0300 and 0301 code. I reset the codes several times and they only come back during the 3rd or 4th hard start, never while driving. The hard starts occur after the engine is shut off for more than a few minutes after driving. I have replaced the plugs, #1 COP, remaining COP boots, Cam Pos Sensor, Fuel pump drive module and had and FI. Also had the fuel pump replaced again on warranty thinking maybe a bad check valve. Again...it worked perfectly for a day and now I'm back to square one. Haven't gotten any codes YET but its only been a day. Bad injector? EGR?
View 1 Replies
I have a 2004 f150 non heritage with a 5.4 its an ext cab lariat auto. It has 350,000 but has been well maintained. The truck runs perfect except sometimes I will hop in and start it up and when i take off it shifts through all the gears before 25mph and when i come to a stop it feels like it downshifts all at once and when i stop it will die. Again it only does this occasionally and the rest of the time runs A-1. This leads me to believe its an electronic error but it is not throwing any codes and cannot get it to replicate the symptoms for my mechanic.
View 2 Replies
I bought an 07 F150 5.4 4x4 with 135k on it about 6 months ago. Shortly after buying the truck I began experiencing a shudder when lightly accelerating up a hill. Also when accelerating hard it would misfire. Thinking that it was plugs or COPs I changed the plugs and coils. That fixed the missfire issue but it still shuddered when accelerating up a hill.
I decided to take it back to the used car dealer where I bought it so they could fix it. On the way there the fly wheel broke. The dealer replaced it and thought that it was the cause of the problem but on the way home I still experienced the shudder. I took it back and they "scoped" it and found that the torque converter was bad. They replaced the TC and now there is no more shudder BUT now I have a new problem.
Now if I am driving at highway speed and let off the gas it feels like it immediately down shifts for a few seconds then shifts back up and coasts along until I give it gas again. There is enough resistance that it feels like a jake brake or that the breaks are being applied. Also if driving along at 30 - 40 mph and just holding the gas in the same spot maintaining 30-40 it feels like it down shifts and up shifts over and over until I either give it more gas or let off all together. Also a few times pulling away from a stop I will get a thump.
I have an appointment with a transmission shop in a few days but today on the way home I put it in second gear while going up a hill so it would not shift and it seemed like it was coughing and sputtering. So now I am wondering if that is what is happening and either feeling like or causing the down shift up shift issue.
If it is a missfire issue why would the new torque converter cause this? It has all new motor craft plugs and all new after market coils.
There are no check engine or other warning lights lit on the dash. I have a cheap ODB scanner and it shows two codes. B1676 which apparently is a Battery Pack Voltage Out Of Range or ABS voltage issue. The voltage is showing at 14.2 volts and there is no noticeable battery issues. The second code is a P1000 Drive cycle test not complete. (this code has been showing for some time the 1676 code is new since the torque converter swap)
One side note: after the TC change every time I start the truck the radio/cd changer cycles though all the CDs. like it it is checking for a disk so it clicks and pops around from a moment. The only time I heard this happen before was after having the battery disconnected. The clock is not reset though like I would expect if it was losing all power.
View 2 Replies
Lost overdrive. Shifts when o/d disengaged. Dropped pan, valve body and found that the servo retaining ring is still intact but the small clip for the center shafts of the servo was broken. Found it loose on the valve body along with a flat piece of metal shaped like half of a hexagon. 3 sided shape, approximately 1 inch each side. Like one 6 inch piece that's folded together. Don't know where that came from. Afraid to put back together without knowing where that came from. Was founded right next to the broken clip. 2007 f150 4.6 4x2 ....
View 13 Replies
I have a 2006 F150 4x4. When the engine an transmission is cold it jerks/ Bogs when it shifts. After it warms up it doesn't jerk to bad sometimes but you can still notice it. Also when it shifts the RPM's drop low causing it to bog and jerk. RPM's will go from 1600 to about 800 when it shifts. It is and auto transmission. Today I wanted to try something so I pressed the button to turn the over drive off. Well it shift real good with the OD Off. Seem like with the OD Off it keeps the RPM's up a little higher so it doesn't bog and jerk. I put an Edge Programmer on it, but that didn't work. Still does the same thing with or without the programmer. I changed all my spark plug and coil packs. Truck goes great until it shifts.
View 1 Replies
Ok have a slight lack of information but ill explain this the best I can. Friend of mine has an 04 5.4 that occasionally wont start. turn the key and gets nothing. other times it will start right up. thinking this is either a starter or ignition switch issue just trying to verify before he drops what money he has to try and fix it. When the truck fails to start he says he hears a click from under the hood and that's it, but if he tries it several times occasionally it will finally turn over and start. I did try to search for this prior but found nothing so I think I'll just have him get the starter test and go from there.
View 3 Replies
Truck is 04 supercrew with 5.4 and 140,000 miles. I have the typical shutter when cruising 55 - 60 and just ease on the throttle to pass someone. I chalked that up to the torque converter unlocking, if I punch it instead of easing into it, it will not shutter. As of yesterday, it acts like the converter is going to full lock up almost immediately. It will bang when it shifts and rpm's drop to lock up range. A few times it has killed the engine when I shift into D. No codes at all, I removed the programmer and installed the stock tune, no change, unhooked battery, no change, fluid is good, and twice after leaving stop signs it worked perfect until the next stop. I believe that it is an electrical control problem.
View 9 Replies
