Ford F-150 (2004-2008) :: Low Idle When Put In Gear And Sometimes Stalls
Feb 6, 2011
I changed the plugs on my 2004 F-150 FX4 with 165,000 miles. Immediately afterwards I experienced a low idle problem. After engine warms up, idle is at about 400 rpm in nuetral or park. When I put in gear it drops to 200 rpm and sometimes stalls. Ford analyzer says misfire #8 cylinder. I swapped coils with #7 and reset fault. #8 cylinder misfire came back. So next I put new plug in #8 thinking the plug was bad. Still have low idle problem. What I should try next?
View 3 Replies
Advertisement
I have a 2004 FX4 5.4 with about 113,000 miles on it. Lately, when towing the camper (around 7000 lbs), truck runs great. However, when I come to a stop, it idles horribly and even stalls sometimes. When I rev it up, runs fine again. It only does this after towing when engine is under load for extended periods of time.
The only code it has ever thrown was for bank 2 camshaft over retarded. My thought was that it could be VCT solenoid for bank 2...
View 2 Replies
I bought an 04 f150 super crew cab with the 5.4L triton in it 3 years ago with 50k on it from my great uncle who was the original owner. It's had a tick to it since he had it but the dealership told him they couldn't find anything wrong with it and to get use to the noise. It's ran pretty good up until last couple months where it's been running really rough and not doing the best. It's still hasn't been all the time but more intermittent and comes and goes, but when it's running bad the rpm drops down to about 200 and my motor sounds blown.
When that's happening I could put in neutral and rev it up and it would go back to normal for a bit, but now it's all the time and stalls out even at 70 on the hwy. The codes it throws are, p1000- monitor checks not complete-more driving required, p0345- camshaft pos sens circ error(bank 2), p0022- A camshaft pos timing-over retarded bank 2. Things I have tried-changed all 8 plugs, added K&N air intake, replaced both cam sensors, replaced fuel pump driver module (due to corrosion). Tonight I'm going to clean the throttle body, mas air flow sensor, change fuel filter.
View 14 Replies
I was driving on the highway today, and when I turned onto the exit ramp and put the car in neutral I noticed my gear shifter shaking back and forth pretty violently. I looked down at the tachometer and saw it idling at less than 200 rpm's in neutral. I got to the light and my car stalled. I turned it back on and I had to feather the gas pedal just to keep the car running. I was able to make it to my local car mechanic with one foot on the gas pedal and my hand on the e-brake. It runs a little rough when in gear but at least it keeps the rpm's up enough to stay running. The check engine light never came on. My guy said that he didn't have the appropriate diagnostic machine, but he's afraid I might need a new throttle body and a new computer which may cost 1000's of dollars. I think the code he told me that he found was P0506. He sent me to a guy that deals only with Japanese cars, but they won't be able to look at my car until Monday.
Any thoughts? Hopefully something that doesn't cost 1000's of dollars. And if I replace the throttle body does that mean I have to replace the computer too? Is there something that I did or that I didn't do that I should have been doing that could have caused this to break?
View 6 Replies
Just got 2005 screw fx4. Seemed to run ok 115000 mi.Had exhaust leak,I put on 3" cat back on. Then I noticed tapping at front of the engine.Turns out tim. chain guides are broken. looks like very common prob after reading many forum/threads. Anyway got timing chain kit, phasers, selinoids. Truck runs and sounds great.But so far had truck back 2weeks stalled 2x at idle.What next??
View 14 Replies
I just bought an 2006 f150 4x4 with a 5.4l 3valve, and this morning when I pulled into work it was idling Rough as I let off the gas and rolled into my parking spot. No check engine light or nothing, just when it's in gear Rpm is at 600-700 and vibrating. When I shifted it into neutral or park it went away and the engine ran smooth. According to the oil pressure gauge I've got good flow. I was told from the dealer that they replaced the cam phasers, timing chain and put new spark plugs in it. What the issue is here?
View 1 Replies
My F-150 has developed a rattle and vibration at idle that only occurs with the truck in gear and stopped (with the brake depressed.) The noise appears to be coming from the front of the truck, perhaps from the driver's side (though it's difficult to tell while sitting in the cab).
Before I go crawling around underneath with my son holding the brake while the truck is in drive--I would sure like to know where it might be best to point the flashlight.
View 6 Replies
I have a 98 F150, 4.2 V-6, 183,000 miles.. Lately, she's been loping at idle. Especially while in gear... almost stalls. Once revved up, everything seems normal. Still goes up hills fine if I get on the gas. The light was on, and I got codes for lean condition on both banks.. (P0174, P0175).
I already cleaned all the sensors in front of the intake.
The MAF was real dirty, and the IAC was full of soot too.
They both cleaned up nicely, but it didn't work.
I borrowed a fuel pressure gauge yesterday, and it showed 12 psi with the "key on, engine off".
It showed 29-30 @ idle, and only went up to 35 when I revved it a little.
The guy at the store said the range is supposed to be "30-45 psi with the ignition on", but I'm not sure if that means engine running or not..?
Either way, it looks like the pressure is on the low side, so I'm going to change the fuel filter next (and hope for the best).
If the fuel filter doesn't fix it, what should I go after next? And, is there a way to test the fuel pressure regulator before buying a new one?
View 14 Replies
Have a 2001 CRV that is running really bad. It almost stalls when I put it in gear or even when the RPM's fall to idle. It is now throwing a p0172 code. I have a simple scan tool and verified the MAP reading and primary O2 voltages as suggested by the manual, both appeared to be normal. It seems all the symptoms point to valve clearance, however the valve were adjusted not 2000 miles ago by the dealer during the 150K service, and this issue has existed before and after that adjustment. I also cleaned the IAC screen with no changes.
View 5 Replies
My F-150 has started acting up again. About 2 months ago it randomly stalled a few times and I narrowed it down to the Fuel pump driver module which was band and I have since replaced. Truck ran fine up until the middle of this past week. Now it runs good at idle, but as soon as I put it into reverse, the engine stalls. I do know that my 4x4 isnt engaging due to a suspect vaccum leak. Could a vacuum leak be causing the stalling as well. The 4x4 not locking in issue predated the stalling issue.
View 4 Replies
I have an 04 f150 fx4 with a 5.4 v8 and it has 125k miles on it. This morning I was driving to work and when I was going down the express way it cut out for about 2 seconds then power slowly came back after about 5 seconds, when it happens I'm either cruising or accelerating lightly. Also when it first cuts out, my headlights flicker, and when I got off the expressway and was almost to work the truck stalled completely after I stopped it started up and I was able to get to work.
View 7 Replies
I've got 200k on my Lariat. Engine was replaced 60k ago. It's in outstanding shape and is driven a lot. Suddenly this morning I start as usual and it runs about 5 seconds then stalls out. Every start, same thing. So it seems I am getting fuel pressure to start but it doesn't last.
I did replace the Fuel Pump Module within the past two years, due to corrosion of the FPM housing. At that time the truck would no start at all. Could it have gone bad already? I'm thinking this must be an electronics failure. It was perfect all day yesterday. 2004 Lariat 5.4...
View 14 Replies
I have the error code P0340 and have changed both camshaft positioner sensors, cleaned the air sensor and throttle body and still the engine stalls. I can accelerate at 40, 50, 60mph and it jerks violently. I tried the "locking it in third" trick but it still jerks. Today I unplugged the left cam sensor and the truck idles @ 400rpms, does not stall, and pretty much drives great! Hook it back up and crank it, within 10-15 seconds it stalls. I plan to check the wiring....
View 14 Replies
My 2006, 4.2 has been really erratically not starting. Turns over fine but will sometimes fire up and tries to run on maybe 2 cylinders, then stalls. Now it won't even do that, nothing. No check engine light or codes. Guess what the thing started up this morning 7 degrees out and running like a charm. Turned off and nothing again. Replaced relay for PCM ,no change, still no codes.
View 9 Replies
I have a problem. My 2007 ford f150 4x4 5.4 triton engine starts to flutter and stalls when its in reverse, engine is warm, and I am backing up a trailer with about 5,000 lbs on it. It drives fine with or without towing. I did notice it does it with nothing behind it on occasion. Whats causing this?
View 2 Replies
I have a 2007 Ford F-150 5.4l v8...
Codes
P0012 int cam position timing over ret bank 1
P0022 int cam position timing over ret bank 2
P0300 random Missfire detected
P0316 engine misfire detected on start up
P0340 cam position sensor curcuit fault
P0345 cmp sensor a circuit problem bank 2
Starts rough, idles rough and stalls occur often when start, after it runs for 5 minutes and sometimes dint starts at all. I replaced spark plugs, coils, cam shaft sensors and had oil changes done and. No effect.
View 8 Replies
2004 Trailblazer 6cy. 2WD - has been experiencing a very rough idle, engine shudders - no matter how long it's been warmed up. Wants to stall off red lights and at very low speeds. Not throwing any lights yet - but the speedo is out ( a cam shift typical problem for this car) so I don't trust the console for lights. Worse when the heat or air is on. Rides fine with more gas/higher speeds. Definitely worse in colder temps but continues even after 40-50 mins of driving. I've heard a number of things, but can't afford to fix them all. I've heard plugs, dirty throttle camshaft, sensors, cam actuator solenoid, etc. All seem to have people who said it fixed and didn't fix the issue. Worried I'm going to stall pulling off a stop and rear end someone any day now. Where do I start!?
View 2 Replies
I have a 2008 LS460 with 79K miles. Everything on the car is great, except this vibration at idle while in drive. For example, when I stopped at a red light I feel this vibration through the steering wheel, in the driver seat and the passenger side. Now, when I put it in reverse, neutral or on park (foot still on or off the brake and vehicle stopped) the vibration goes away.
View 14 Replies
We had 2 Trucks that had the reverse go out in the last month. What would be the cause ? Is there a defect in the Trans?
View 2 Replies
I've been noticing more and more lately that while my trucks in 1st or maybe 2nd gear, say, slowly coasting around a parking lot for example, there's a whining noise coming from either the rearend or the tranny (cant tell which). It gets louder and more high pitched as I move faster then disappears as soon as the truck shifts gears..
Is this something serious like my transmission on its way out? From what I gather a lot of people seem to have a similar thing going on.. From what I can remember my truck has done this since I bought it, but lately (and maybe its just me) I seem to notice it more like maybe its getting louder..
View 7 Replies
I have a 2006 F-150, V6, automatic transmission, a little over 214,000 miles. When I started it up this morning, no issues, but when I dropped it into reverse, it started shaking pretty bad. Got on the road and put it in drive, and the shaking continued, then the check engine light started flashing. Haven't had any problems up to this point. Checked all the fluids including the transmission fluid a few weeks ago and all was well.
View 4 Replies
