Ford F-150 (2004-2008) :: Running Rough With Code P0171 - Engine Light Stays On?
Dec 16, 2013
I just started to have this problem yesterday. Engine light comes on and stays on. Engine shakes and truck won't go over 50 MPH. Autozone code checker came up with P0171.
Truck has about 95K miles and I had the spark plugs replaced at 75K miles.
Transmission was rebuilt at around that time also.
I only drove it to Autozone and back today to post the code and see what everyone's opinion is as to what's wrong.
Here's what the printout says : P0171 "Fuel Trim Bank One Condition"
View 6 Replies
Advertisement
My 1999 F350 SD V10 that would crank but not start. I ended up checking numerous things because before it decided to truly stop running, it would run rough for a time and then be fine. The check Engine Light came on and I got the codes P0171 & P0174. Well, I bought MAF Cleaner and took the air cleaner housing off, disassembled it and thoroughly cleaned the sensor and replaced the air cleaner. I continued to get those same error codes, but before I could go any further, the truck totally died. It sat for nearly 2 months with the bed in the air as I had decided to lift the bed to check the fuel pump vs. drop the tank.
Fast forward a bit and I have since replaced the fuel pump and put $40 of Premium Gas along with Royal Purple Fuel Treatment in the tank because I figured things got stirred up and could use a bit of cleaning. I do not drive much, and during the first few trips, it ran perfectly. Then today, it started again with the rough running and trying to die if I let it idle. If I pushed on the gas, it would completely smooth out. If this were a carbureted engine, I would think the low idle was set too low, but since it is not, I am guessing it is one or more of the sensor/s that is/are causing the issue.
I am disabled and can’t play parts swap until I hit on the right part, so I was hoping that I might get some guidance here to narrow things down to the most probably causes so that I won’t go broke changing things until I hit the “right one”. The truck has 153,000 miles on it and I had bought it from a retired couple who used it to pull their 5th wheel travel trailer, so it had mostly highway miles on it. It was immaculate when I bought it and ran perfectly, needing only normal maintenance (oil changes, etc.) over the past 12 years that I have owned it. In those 12 years, I have put about 60,000 miles on it.
View 3 Replies
I just had my 04 5.4l engine rebuilt. Ive driven it about 500 mi and it started running rough at a stoplight. I tapped the accelerator and it started running good again but service engine light came on. I pulled the codes and they were P0022, PO345, P0340,and P0430. It has done this several times now. Everything was replaced including the phasers, except for the camshaft sensors. Could they cause this problem?
View 3 Replies
My daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
View 6 Replies
I've got a 2000 f150 with a 5.4 and 135,000 miles. The other day it was driving fine then i stopped and got gas and after that it was boggy and running rough so i thought bad gas but i ran through that gas and got more at a different store. The cel came on i got it checked it was misfire cylinder 1 so i put new cop, spark plug, and injector. Unhooked the battery and then the light came back on so i ran the code and now im getting a p0171. I checked the pcv and sprayed around the intake and vacuum lines. I also checked the pcv hose and elbow in the back and i found nothing its a fairly new hose. So, it does run rough it shutters a lot.
View 2 Replies
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 Replies
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
View 5 Replies
I have 2007 explorer with the 4.6 V8....
Recently it started running horrible. Rough idle, drives badly, hesitation, etc. Check engine light is on, code P0171. I cannot find a vacuum leak, and i am pretty much at a loss. Before it started running poorly i replaced the thermostat, and flushed the coolant. I am assuming this is a coincidence.
View 1 Replies
My wife's 06 expedition 5.43v runs rough loud and dies. Not all the time just when it's to hot. I got a code it's p0022 cam sensor. I changed both started the rig up and heard loud rattling like metal maybe chain. It lasted for a the length of my video 1.4mins give or take then went fine, i turned the car off and back on everything seems fine. I know I got her oil done after driving. She had metal/plastic in her oil. I had all plugs done and actually i re did the 8th cylinder plug because it was miss firing and i pulled it by hand with only the socket no ratchet. I'm thinking the chain is going bad if not already bad. Only 113k miles my 04 f150 5.43v lasted 250k before motor swap...
View 7 Replies
What a p0171 is?
View 2 Replies
I picked up a really cheap Hyundai Elantra 2005 that the kid that owned it really beat up on. Right now I am trying to sort out the issues so that it can become my daily driver for the next few years.
Second issue, The check engine light is on and it is popping up a P0171 generic engine running too lean code. The car looses power sometimes and I can smell gas in the car. I have a friend that is going to be loaning me his MAC code reader so that I can see if it is one of the O2 sensors and if so which one tomorrow.
View 16 Replies
In the last month, my car has had an awful time starting on 2 different occasions. The first time it ran really rough for about 1 minute then was ok. The second time was the same but the engine light came on. Took it to an out of town dealer and he said it showed a misfire code but could never find anything else and all looked OK. Spark plugs?
View 4 Replies
My Focus has 102,000 miles. It has thrown a p0171 code and I have been attempting to fix it. So far this is what I have done:Changed MAF, air filter, PCV Valve, plugs, Valve cover gaskets, Bank 1 O2 sensor and fuel filter. All new. I have cleaned the throttle body, fuel rail intake manifold. Cannot hear vacuum leaks and tested for leaks with carb cleaner.
Symptoms: engine cranks but has a hard time starting, usually on second try. When tank is about half full I get Rough acceleration, higher RPMs (doesn't change gear) and engine stalls on hard left turns. Idle gets rough at times but usually stabilizes at around 700 rpms.
At the beginning, #1 spark plug chamber had a lot of oil in it. It's been a few months and no oil after Valve cover gasket and PCV change. Tested coils and the plugs get a spark. Before I start messing with the fuel pump, am I missing something else that I can do?
View 19 Replies
My 04 F150 has started having a rough idle. While in park the engine will stall out with the A/C off. Also when in drive the truck will idle close to 1000rpm's. I had to the fuel filter cleaned and also the MAF sensor cleaned. Also did a vacuum check on it. Pulled the code and it's throwing a Lean Code. What else should I be looking for?
View 12 Replies
2004 F150 5.4 3v. I bought the truck with 102k on it, it now has 124k. In the morning, when the outside temp is between 30-50, the engine starts and runs fine. When I get to the first red light ( about 1 mile away) within seconds of the engine at idle, engine starts to run rough and CEL. Every time the code is p0351. If I let it sit in the driveway to full warm up... no problem. If I start the truck, shut it off and restart...no problem. It only happens at the cooler temps. I have changed plugs, used motorcraft, nickel antiseize, torqued, etc. Ford changed the coil, I have changed the coil, cleaned MAF. As soon as I cross the intersection, light stays on, rough running clears up, and runs like a champ for the rest of the day.
View 2 Replies
For the last few months my truck has been throwing an intermittent check engine light due to the same code every time - P0171. The dealer has allegedly checked everything and has given me the "We have done all we can do" speech. Lead tech even suggested that since today's fuels have alcohol in them, that a check engine light would be normal. The truck has been in the shop 3 times with no success or even remote possibility of what the problem could be.
The check engine light has since gone from intermittent to constant and comes back on after 5 drive cycles after clearing with an OBD2 scanner. Also, I'm now getting a P0174 code.
Personally, I think they're trying to blow me off because I'm a few months and about 2k miles away from being out of CPO warranty.
Truck is a 2013 F150 Super crew 2wd 5.0 with about 45k miles.
View 9 Replies
Well my girls 2006 passat is showing the check engine light. she took it to autozone and the code was, P0171. what does the code mean and what do i need to replace?
View 4 Replies
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 Replies
I have a 2004 VW Touareg with 116K miles. Yesterday the check engine light came on and she is running very rough at low RPMs. The manual tells me that there is either a problem with the exahust manifold or an O2 sensor is bad. It feels as if she is struggling for air. When you start the vehicle the check engine light flashes then stays on in the cluster. What can I expect when I take it in to the dealership? Is there anything I can check before I take it in?
View 4 Replies
97 F150 4.6 Vin 6, 5-Speed Trans, 200,000mi, Rebuilt recently. I was on my way to get my truck smogged, but she threw a code, P0171. I read somewhere to clean the throttle body elbow, which I did (needed to do it anyway). After I had everything put back together, I start her, and it's rough and immediately dies. If I keep the RPM's at about 1.5k for a minute, then let off, the truck will run fine for about 30-45 seconds, then die again. I just replaced my IAC and the problem persists.
View 8 Replies
I have a 2006 Ford Ranger with the 3.0L v6. The check engine light came on and the code it is blowing is a P0171. It runs rough at idle or when I let off the accelerator and "fine" at speed.
The code told me to check/clean the MAF which I have done. Next on the list that I saw was the PCV valve. I disconnected the electrical to it and then disconnected the hose. Some oil poured out of it... not a lot but some... The valve still seems free, it clicks when I rotate/shake it and I can blow through it (I know, highly scientific). I can replace this (if I can find it, Napa and Advanced Auto don't have a part that looks like it...) but I'm wondering what else could be wrong.
View 1 Replies
