Ford F-150 (2004-2008) :: Ticking Noise From Front While Driving
Jul 3, 2011
I have a 2005 F 150 5.4L and i just changed the front rotors, pads, and calipers. Because the passengers side caliper had locked and the rims was really hot and i knew it was the caliper so i changed both the driver and passenger side calipers and hoses. A month before this i had changed the pad and rotors but after the caliper locked it put grooves in the rotor and damaged the pad but the pads and rotors i bought have a lifetime warranty so i got a brand new set and changed them while replacing the calipers.
After installing everything i bleed the front brakes. But did not bleed the rear and i am wondering since i did not do the rear even though i did not touch them it is causing the front to make a ticking sound the whole time i am driving and it is starting to annoy me even though it has only been 4 days since i did the front brake job. I put Duralast rotors and Duralast Gold Cmax Premium Ceramics Pads. What is causing this ticking.
View 1 Replies
Advertisement
I recently installed a 2" aluminum HBS leveling kit on my F150. ('04 FX4 SCrew, 5.4, 61K miles). I was excited to finally improve the truck rather than fix something. The install was straightforward and I didnt have any issues (other than Cleveland, OH rust).
After installing the kit I noticed a whirring noise coming from the front end while driving, but I didnt think much of it and I got an alignment a couple of days later. Immediately after the alignment, the problem is still there. It sounds just like aggressive mud tires driving down the road, so I think it is coming from the tires.
The noise follows the speed of the truck (the pitch gets lower as you slow down) but you cant really start to hear it until you slow down below 45 mph. It is much more noticeable at lower speeds (probably because of the lower wind noise in the cab). I dont think it would be a CV joint/axle issue, but who knows. I am considering taking it back to have the alignment checked, but I figured I would check on here before I do.
I just bought this truck last fall, and it is one step away from being traded in because of the countless nuances this thing has (wet floors and consequently rust everywhere on the inside of the cab, rattling window trim, shaking bed, squeaky rear window, noisy phasors).
View 14 Replies
I am 98% sure my 17" chrome clad wheels are making a clicking or ticking sound as I drive. I took off the plastic center cap and the noise changed.. it's less than constant now.
View 3 Replies
I have a 2004 ford f150 5.4l v8 triton lariat and while at idle it has a ticking noise like this video
YouTube...
However I also have a rattling noise when decelerating at around 2000 rpms that sounds like a loose chain in a box. Not sure if its VCT sensor or cam phasers ...
View 1 Replies
07 f150 screw 5.4 104+ miles, loss of power and ticking noise (sounds like no oil)on passengers side, no engine light, no codes, ford dealer changed coil packs and plugs, inspected valve gear on passengers side and nothing seemed out of spec, no broken springs, followers, lifters, manifolds on both sides have been replaced very recently.
The ticking noise began about a week after an oil change, truck runs fine but no power/sluggish. exhaust is magnaflow side exit and seems to be louder inside the cab than usual or could be just me.
Truck had a miss that i was trying to find prior to oil change and ticking noise. it ran well for a week with the tick before (and miss) the loss of power which started after a 30 min drive under load up hill. it almost felt and sounded as if the muffler was dragging on the road for about 100 feet, ran fine for two miles until it was shutdown. restarted fine but flat when you get into it.
Clogged cat/cats; internal damage to muffler, oil issue even tho the gauge reads fine.
View 10 Replies
I have a question about my 2007 F150 4x4 with the 5.4L. It has a ticking noise sound coming from somewhere around the motor, but it's not there till the motor has warmed up. It almost sounds like a exhaust leak, but I'm not sure. What it might be, or what to look for?
View 11 Replies
Getting code P0022, which is over retarded cam position, drivers side bank. My 2004 F150 has the 5.8 triton. I have replaced all cam phasers and tensioner a as well as the timing chains. I have also replaced both VCT solenoids. Before I was getting codes for both banks, now just the code mentioned above with a slight ticking as well. My question is this... What am I not seeing? What could be causing this?? Would it be beneficial t get the lockout kit for the phasers to always keep them open?? Seems to stall a little at very low RPM like when you are off-road.
View 1 Replies
I recently got Gibson Performance Headers on my 2006 Ford F150. And when you cold start it or just start it period it has a odd ticking noise on the passenger side.
View 3 Replies
the F150 of my brother has the follow diseases:rough running ticking noises, low mileage per gallone, blue smoke out of exhaust after start, i have ordered the cam phaser, hope, that will be the reason. But today, my brother means, i have to do a test drive, because the truck has no power. and really, feels like missing of one or two cylinders. Very bad performance. Is it possible, that the reason are the phasers?
View 4 Replies
Once winter arrived I started having problems with my truck running like crap after warm up. However, I noted that during initial start up and lasting till the engine got to its Normal Operating Temp, it would run like a BAOH! Once the engine reached Normal Temp, it would fall flat on its face if I got into it down the road. I wasn't getting any codes, so knowing about the EPU and timing; I opted to change out the O2 sensors. Bought all 4 sensors, Bosh, installed them and within a day got a P0420, P0303; known as Cat system efficiency below threshold and a #3 misfire. (side not all plugs, timing chains, COP's, Phasers, cam positioning sensors have been replaced within the past 18 months) So I decided to take the COP off of the #3 cyl and swapped it with the #5 cylinder; still getting a misfire on #3.
Didn't pull the plugs, knowing they have less than 50,000 miles on them. The problem lasted about a week, off and on with heavy acceleration. Then last Saturday I was driving around town, came to a stop light and the engine shook hard while stopped, missing for a few seconds but not sending a code. Upon acceleration I noticed a loud ticking coming from the right (passenger) bank. The truck practically fell on its face through 3,000 rpm's. No power, and still no codes. I got home, pulled out my steth and listened. I got a loud ticking on the cover at the #3 and #4 Cyl. I know ya'll acclaim ticking to the phasers but it's a totally different sound. Its not coming from the front of the cover as it did when my phasers went out. This is strictly confined to #3 and #4. Took it to FMC., for diagnostic fee and a day later they said, symptoms of lash adjusters. I told them I'd pick up my truck.
Got in it, and drove it home and that noise is loud, echoing through the right exhaust. Seems to be running very rich, still no power what so ever and now I pull up in my driveway and instantly get these codes. P0316 (misfire on startup), P0420 Cat efficiency below threshold, and p1000 (due to resetting my computer back to stock before taking it to FMC) I thought about doing the job myself, but working 120 hours a week I don't see how, and I'll need to buy the valve spring compressor and timing chain wedge (260.00 set) So I started calling around to mechanics, 10 to be exact, none of which, will even look at the truck.
View 1 Replies
I have that wonderful ticking noise... Here is some info on my truck: Its 133k, 5.3L 3V. I put new plugs in it and changed the oil (YES the right filter and oil).
Okay, so I'm trying to make sure my diagnosis is what I think it is before I start digging into the motor and get angry because I ordered the wrong parts.
Preface: I got the truck from a deal auction. I was told it ran great, well when I got it, it had this tick. It comes and goes as it pleases (not dependent on the weather or RPMS. The noise is consistent, it gets faster as RPMs rise, it doesn't go away after 1,200 rpms. This lead me to eliminate cam phasers as the issue.
Now here is something odd: After starting up the truck, initially it will be pretty quick and have great throttle response, but after that it will start act like someone put on the parking brake. It can barely accelerate and when you put it to the floor it gets worse. It seems to accelerate best at half throttle. The second part is the truck will shift, dropping the rpms incredibly low and the tick gets louder and more spaced out (leading me to think it's rpm dependent).
All of the noise seems to be localized around the passenger size head area. If I unplug the VCT solenoid the ticking doesn't seem to be as loud if I drive it the next day, and it doesn't do the shift into lower rpms and accelerates wonderfully. Leading me to think it's either the timing is off and when the phasers kick on it goes way out of time and causes it to go into limp mode...or the VCT solenoid is bad?
The ticking never fully goes away, but it has it's quiet days and LOUD days...
View 1 Replies
My alarm started going off by itself and my truck would not start so we unhooked the horn but the alarm was still trying to go off making a ticking noise when the horn should have been honking. so we also unhooked the alarm. And it started right up. I've been driving it with those things off with no problem. But today it wouldn't start again and its making a ticking noise like the horn is trying to honk.
View 6 Replies
2008 - <40k miles. Drove the car a good 50 miles yesterday with no problems. today as i was leaving the house, i kept hearing a ticking noise that was progressive in frequency the faster i drove it. i only made it to the end of my street, went back home to drive off in my gas guzzler for my 50mile round trip today.
View 2 Replies
I gotta a roaring noise coming from my right front while turning. Planning on replacing just the wheel bearings tomorrow & not the whole hub assembly(2008 2wd). Is there a thread that lays out the steps and other parts I may need? I've seen alot different stories on the net on how to do it. Everthing from I can press new bearings to I have to do 4x4 hub conversion. Seems to be some confusion.
View 2 Replies
Driving to work my trucks radio turned off.. My abs light came on.. A screeching sound from front hubs.. Then I stopped abs light went off hubs locked.. Air bag light came on.. I hit the power button on radio it displayed low battery.. All interior options were off. Outside lights dim .. When I got to work I shut it off and tried to restart... Acted like battery was dead.. It's a 3 week old battery. I also noticed , it seemed like I could not turn off my head lights.. Switch did not seem to make any difference with lights. After being off for a mon. The lights got a little brighter. Is it just the alternator? I got no low battery or dummy light. It did have a mildly sluggish start.
View 5 Replies
My 2008 F-150 recently started making a funny noise from what seems like the front right wheel.
The weird thing is that it will only make the noise while accelerating. The second i take my foot off the it stops. Also, the sound stops if i put it into 4WD and does not happen at all in 4WD.
It has nothing to do with turning or breaking. It only makes the sound in 2WD while my foot is on the gas.
The sound is kind of weird. It sounds like something is loose, and it sounds similar to tin vibrating on metal.
At first i thought it may have been heat shielding rubbing on something, I checked under the truck and found nothing loose.
It's weird that it only happen in 2wd yet in the front end.
Someone had mentioned that it may have something to do with the fact that there is no torque on the front wheels in 2wd and when i put it into 4wd it put torque on it, whatever might be loose then becomes tight.
View 6 Replies
I've got a clunk in the front end....replaced all the ball joints......checked the sway bar......checked the tie rods......can't find anything wrong...... Shocks go bad and clunk???
View 14 Replies
I have a problem transfer case 2006 f-150 , it tries to engage once in a while as I am driving and makes a terrible noise . I pulled the vacuum lines off at the hubs on each front hub and it stopped trying to engage. What the problem could be ?
View 1 Replies
My 2006 f-150 with 71,000 miles has been making a groaning noise in the front when I reach about 20mph and it will intermittently stop for a few seconds and then start again. And when I turn left it completely stops. I have had it to my Ford dealership three times and they replaced my steering shaft and brakes and checked for anything rubbing and have not fixed it. I'm worrying about this every time I take a trip.
View 3 Replies
My 2005 F150 is making a thumping noise in the front end. It increases as speed increases and is more pronounced when turning wheel left and almost goes away when turning to the right. Sometimes at higher speeds I can feel it in the gas pedal. Seems to be coming more from the driver side but I could be wrong On that.
View 3 Replies
Alright, so about a month ago I was driving when I heard a terrible noise sounded like a pop can stuck between a bike tire coming from the front end. I figured this was the dreaded noise most folks hear when the 4wd system isn't getting enough vacuum.
It did this for about two days, even after replacing the IWE solenoid, then it just stopped and I haven't heard it since. Me being on the cautious side, I'm a bit worried. I haven't jacked the truck up, but I did (brace yourself) lay under it while my buddy drove slowly over, there was no unusual movement.
Question is, if I had to replace anything, what exactly would it be and how much am I looking at? My warranty will be up in about a month or so and Ford has been less than spectacular with repairs thus far so I'd like to go ahead and fix it myself
View 1 Replies
