Ford F-150 (2009-2014) :: Camera And Reverse Sensors Have Quit Working
Nov 7, 2012
Does the Ford emblem/camera just pop off the tailgate with a screw driver? Pry from top or bottom? I'm trying not to break anything here. I removed the tailgate panel inside and can't get any access there.
Both the camera and reverse sensors have quit working. I'm troubleshooting both but I'm not sure they are related. The camera died first but worked sometimes after slamming the tailgate. Sensors quit sometime after. Don't really care about the sensors but the camera is essential for hooking up the trailers.
I was hoping the wiring from the tailgate to the plug would be cut but that doesn't appear to be the case. I'd like to check the camera itself next. Ohm it out or something, I don't know.
View 4 Replies
Advertisement
On occasion I'll have the reverse sensors quit working. I'll drop the shifter in reverse and the 'OFF' light on the button will illuminate. I took the sensors out and blew them clean with compressed air, dielectric geased the connectors and reinstalled the plugs. Let's see if that does the trick.
As mentioned, it's occasional and nothing in particular will trigger the fault....it's very random. Something tells I haven't seen the end of this problem, but tracking an intermittent fault is tough.
View 9 Replies
It's abnormally cold here in the Northern Va area single digits with windchills in the negatives. I ran through the car wash, one of those that hand dries it afterwards to get the salt off my truck. After running the roads I went to back in to a spot and the sensors are going off. Nothing is blocking them so I'm thinking water got inside and froze?
View 4 Replies
I have a problem with my Backup reverse camera, actually my tiguan not bring it with camera backup and I install and change the radio for rcd 510 bosch with backup camera port,
View 6 Replies
Issues:
1. Backup camera sporadically does not come on in rear view mirror. Has already been replaced by Ford dealership.
2. Backup camera settings Visual Park Aid and Guidelines sporadically are set to 'off'
3. While truck is running, start seeing warnings/hearing chimes. Emergency Brake (which isn't set), Engine Overheating, Check 4X4, etc.
4. Truck will NOT start. Won't even attempt to turn over. When this happens, I have a radio but the LED screen is usually blank.
These sporadic issues are starting to seem to be related to the use of the emergency brake. Use of the emergency brake does not always immediately cause issues. Now that I feel like there is some kind of connection, I have been setting the e-brake when I park it (even if not needed) trying to force things to happen because Ford says if they can't make it happen they don't know where to look/what to fix. I can't always make things happen by using the e brake...but am noticing things happen more often when I DO use it and when things happen (like backup camera won't work) setting the brake will make it come on and then I can release it and back up. If it won't crank while the brake is set, releasing it will cause it to crank. The other morning when I had all the warnings/chimes going off setting the e-brake made everything go back to 'normal'.
Yesterday when I came back from lunch I parked and set the e brake (on level ground). Got in it to leave work, left e-brake set, stepped on regular brake and tried to crank....nothing but radio. Called dealership. They had me try putting the key in, pressing the regular brake, and try to move the shifter from Park to N. Shifter wouldn't move. Then asked to turn key to just get it 'active' and try again. Shifter wouldn't move. Asked me to turn the key to crank and try again. Same thing - shifter wouldn't move. Truck finally cranked after I released e brake. Came home, parked and set e brake and turned it off. It re-started right up with e brake still set.
View 14 Replies
i have a 2013 Ecoboost Screw. This morning, I was leaving for work about 0445, and was pulling out of my driveway, when I realized my headlights were not on. I tried rotating the switch a few times off and on, and still nothing. I pulled back in my driveway and checked all fuses for headlights, both low beams and high beams. All good. My parking lights, turn signals, and tail lights all work.
When I got home from work tonight, I tried a few more things. I pulled the lamp housing and checked for voltage directly to the bulb. I get 0.9 VDC at one pin and 0 VDC at the other two. Not nearly enough to fire up a bulb. To a known good ground.
I opened the dashboard to check the harness at the switch itself, and when I unplugged it, all lights turned on (except the headlights). Is that a failsafe in case the switch goes out while driving?
As a last ditch desperate measure, I disconnected my negative battery terminal for about 15 minutes just to see if anything changed. I don't know where else to go from here.
View 3 Replies
Yesterday I replaced the battery in my 2013 F150. Since I did this, both running boards just stopped working. I checked the fuse, it is good. Is there a connector around the batter that I may have knocked loose?
View 11 Replies
The media button on SYNC quit working last week(2010 F150, six cd player, no navigation). No voice commands or phone, also can not perform the "Master Reset" because the phone button on dash does not work. I have had this issue before and pulling fuse 13 for a couple of minutes always fixed it. Pulling the fuse no longer fixes the problem. I also tried disconnecting the battery.
I left the cable off overnight and still no luck. I came across a similar problem being fixed by a ACM reprogramming TSB (SYNC (possibly) Fixed by TSB 11-10-22) on a another forum. Do reprogramming working on a dead SYNC system when the hard reset was tried and did not solve the problem? Dealer did not want to reprogram ACM and told me need a new APIM.
View 6 Replies
I took my truck to the dealer because my steering wheel buttons quit working as far as going forward or back between songs via bluetooth. The tech said the buttons don't work via bluetooth from the factory and I told him he was wrong. They worked in a 2007 Edge, 2008 F150, 2009 Fusion, 2009 F250, and until the day before, my 2012 F150. He said "You must be mistaken". I took it home, pulled Fuse 2 (Sync) waited a couple of minutes (Nice place for the fuse box, Ford) put the fuse back, let Sync load, repaired, etc, and my steering buttons now work again. I only use bluetooth with both my S3 and Note 2, so if your buttons stop working, do you always have to pull the fuse, or is there an easier way to fix this? That's the fix I found.
View 8 Replies
Have a '13 F150 Platinum. Recently three things "broke" at the same time and I suspect a fuse but cannot locate the right one. At first I thought it was just the GD Opener, but when trying to reprogram it, I realized the red lights were not lighting up and the Drivers side Vanity Mirror light was not working.
About the same time, I noticed that the Instrument Cluster Memory function quit working and weirdly, every time the truck is switched off and then back on, it always comes back to the trailer tow screen for my Snowmobile trailer.
I thought i had it solved when I found that the trailer back-up lamp relay power fuse ( #43 in fusebox under hood) was blown. I replaced with a good 15 amp fuse and the problems are still there. I have searched high and low and cannot find a fuse for the Car2u GD Opener or the Driver Vanity Mirror Light (neither Vanity light for that matter. I tested all under hood fuses, but the kick panel fuses are impossible to check one-by-one.
View 3 Replies
How to fix a backup camera that quit working this morning. Never had a problem till backing into a parking spot at work this morning.
View 1 Replies
I checked a few fuses when my 12v power sources quit working and now the engine won't start. I get a start system fault and hill incline fault among other warnings. What happened?
View 2 Replies
My work truck that I drive, a 2006 F-150 Lariat 4x4 extended cab, rear parking sensors quit working. The button on the dash is lit up all the time like when you shut it off. I posted this on the F-150 section too and was able to find a suggestion that you can listen to each sensor while in reverse and if you don't hear a clicking at the sensor it has failed. All (4) sensors are clicking away while in reverse so not sure what else to check, no one in the F150 section, so that is why I put it here.
View 3 Replies
On one of the trucks in work, the salt has corroded the truck side plug for the reverse camera in the tailgate. Because of this, the camera no longer works.
Is this part of the whole rear wiring harness, or it the tailgate plug a separate pigtail that can be replaced? If it is a separate part, what is the part number so I can order it?
View 1 Replies
So when I got my car a couple months ago there was this problem where the backup camera wouldn't come on every now and then when I shifted into reverse so I decided to get it fixed under warranty. the dealership said the problem had to do with the whole infotainment system or something so they gave me a whole new center console and navigation screen for some reason but after I got my car back a couple days ago it was working fine up until today where the back up camera won't even come on at all anymore. I've driven the car about 5 different times today and the backup camera never came on once.
View 3 Replies
My backup camera (2013 KR) comes on in Neutral. Is this normal? Looks cool when going thru a car wash though....
View 14 Replies
I have checked the fuse number 38 and it's fine, and I've also checked the bulbs and they look good. Where else do I look to check for problems with my reverse lights not working? I just had my transmission rebuilt, and wondering if a sensor or something went bad?
View 1 Replies
So I completed the install of the OEM reverse camera with ECS wiring harness. I followed the wiring diagram, tapped into power at the back of the head unit according to this thread but nothing works. Neither the hatch lever nor the camera. I have to open the hatch manually from the inside.
I double checked the wiring diagram and everything is correct. I also plugged the old hatch wiring harness directly into the new camera by bypassing the ECS harness, and afterwards the hatch lever actually works... however, with the wiring harness installed, with the old hatch wiring harness inserted into the ECS wiring harness, the hatch lever does nothing.
Does the handle need power to function?
Did I tap into the wrong location for power? I was going to use a fuse tap, but couldn't get the fuse tap to plug in so I used the head unit. Where did people tap into for power? Did people use the red/white wire at the back of the head unit? I redid the connection with a simple twist joiner but things still don't work.... I also ran a new power line through the car to see if that would solve things. So is my problem:
1. faulty wiring harness
2. improper power supply
3. faulty camera unit
4. other.
View 9 Replies
I have a 2011 F-150 Super Crew and have had to replace the back up camera due to a malfunction. Once the dealer replaced it under warranty I was no longer able to get all the options that the previous camera had. Since then the 2nd camera went bad and I just had it replaced again. This new camera still is missing 2 of the options the original camera had. The dealer now tells me that they must have been deleted off the software on the replacement cameras. They were unable to verify that through Ford though.
View 6 Replies
Lately my backup camera doesn't turn off when I shift from Reverse to Drive, I have to put the truck in Park and then go to Drive to make it turn off. Is this a software update problem?
View 10 Replies
I bought a DVD player for my 2010 corolla,everything is ok the only problem is I can't see reverse image automatically when I reverse my car.
View 4 Replies
