I was letting my truck idle to work on a cooling issue when I noticed oil coming from my fuel pump! What would cause this? It wasn't coming from were the pump bolts to the timing cover it was coming out of the side of the pump it looked like? I'm going to get a new one.
View 7 RepliesWorking on my cousin's 84 F150 351w HO with a Holley 4180 4bbl and auto trans.
I rebuilt the carb because of sticking floats (that and it was filthy and sitting). It fired up and I drove it to my uncle's shop a ways down the road before even adjusting anything. At the shop, it fires right up, idles great and floats and idle mixture screws are now adjusted.
It has a dead spot right off of idle that's been driving me crazy, and stalls in gear if I'm not careful with the pedal.
After reading around here, I looked down the carb to make sure the fuel was squirting as soon as the throttle moved, and noticed there was NO FUEL squirting from the nozzles. So that explains the dead spot...
There was just the needle, then the nozzles, then the screw that went in, same as they came out (only cleaner). Wondering where to go from here to get these working again. Going to pull the nozzles off and see if there's anything obvious going on in there.
I've had a fuel leak near the pump of my 79 F150 with a 400 for some time. I didn't know exactly where it was coiming from, but fuel was being sprayed on to the oil filter from something near the pump. I assumed it was the steel line, and that it had rusted through or cracked, and was going to replace it when I had a chance. I was poking around today though, and realized that the fuel was not leaking from the line, but from a hole in the side of the mechanical pump.
For someone who knows what these pumps look like, there is a horizontal cylindrical bump out near the top of the pump, on the side of the pump that is away from the engine. The fuel is spraying in a mist out of one side of that. To me, it always seemed to be a screw channel, but I didn't think the pump was 2 halves put together? Need to know more about my pump, what that bumped out section is, or why/how fuel could be spraying out of it.
This van has had a couple of fuel pumps, no surprise there, and i need to look through my paperwork and find out how many miles the current one has on it, but it has the STRANGEST habit I've ever had on any vehicle. Starts fine, runs fine, no fuel pump noise when van is running, and when you turn it off, the fuel pump creeks on and off for several minutes.
I mean a strange creaking noise almost like a shorted electrical device or a vehicle's brakes when you park it on a hill and the breaks creak as it settles into place. I'm probably doing a lousy job of describing this but i don't know how else to describe it!
ALSO, if you lay under the van and wait til it stops creaking, you can tap the bottom of the tank and it will creak for a few more seconds. You can tap repeatedly and make it creak more. Is it about to explode? Can i trust it on a road trip?
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?
Why the frame mounted fuel pump might run after the key is turned off? Then when you turn the key on it may or not run. If it does run it keeps running. shouldn't this shut off after pressurizing the line? is their a pressure switch in the pump that's failing? This has the 3 pump system...
View 4 RepliesI have an 87 F150 4x4 4.9L EFI with a single tank. Fuel pumps keep running even when the key is off. I tried swapping relays but the problem still exists. The engine will start and run OK for about 15 secs. then die. I installed a new low pressure pump, high pressure pump seems to be OK. I also installed new fuel filters. I dont want to just throw parts at this truck, where do I go from here?
View 4 RepliesI have a 1994 Ford 460 motorhome with a intank fuel pump that quits when it gets hot. so I was thing of butting a heavy duty in line pump on and just pull it through the old pump can this be done safely. Or is it best to drop the tank and just put a new fuel pump in.
View 10 RepliesMy F250 heavy duty isnt getting voltage to the fuel pump relay.....
View 2 RepliesHave a 95 Bronco with 5.8, I turn the key on and fuel pump doesn`t shut off. Changed fuel pressure regulator still no shut off. Changed relays, no luck. Have 38 pounds pressure with key on, but no start. Checked spark just in case, and have fire. Don't know what to try next.
View 10 RepliesIt started out w/ my wife swapping from the front fuel tank to the rear tank due to the fuel qty getting real low. Then the next day when I drove it I had bad fuel qty and amp meter indication, I found a blown fuse on my fuel qty/amp meter gauges. I replaced the fuse and got my indications back. Now I hear my front tank fuel pump is running constantly when selected to its position. Its now full of gas and still runs constantly. The rear tank/pump operates normal. I am wondering if I ran that pump empty and lost its prime? What is the best way to burp it?
View 9 RepliesPulled codes awhile ago...got a 96. Says "Fuel Pump Circuit Open"-Battery to ECA (1988 On). What is an ECA maybe the Pump Relay? And does this thing have a fuse for the fuel pump in the panel. Fuel Pumps not getting any juice.
View 1 RepliesOk so my son and I are new to this whole truck restoration thing, but we're eager to both learn. We recently scored a 77 F250 camper special that's sat for about 14 years. When we bought it it was running. The previous owner had done quite a bit to clean it up. When we got it to the house we drove it around a bit for fun, and parked it until we could drop the tanks to clean them out. That's done, we've replaced the fuel sensors in both tanks, the lines are clear based on us blowing air through them from the engine side back to the tank side before connecting to the tanks. The mech. fuel pump is brand new and seems to have suction when we turn the truck over. We've installed a fuel filter before the pump in an effort to filter any possible residual junk out of the lines, but we can't get fuel to the engine! (Yes we put gas in both tanks.) The truck will run when we run a line Direct from the pump to the a gas can, but not when connected to the tanks. What could we be missing?
View 2 RepliesI have a F-250 4WD with 7.5L which has a MC/Holley 4180c sitting on top. It was getting very poor mpg (like 5-6 miles/gal) and then was getting harder and harder to start. This progressed rather quickly to not starting with fuel coming out of the primary vent tube. I suspect it has to do with the primary float stuck open. I was considering rebuilding the carburetor. Is this over reaction prematurely or is there something like float adjustment that may rectify all of the symptoms described. If a rebuild is in order what is the information I would need to ensure getting the correct rebuild kit. Info that I have so far from research is it is Motorcraft ID #E5HE-9510-MC.
View 6 RepliesI have an 88 E350 With a 460 EFI . Problem is there fuel is coming out of the ecs canister . It has the dual canister set up fuel comes out of the rear one after the engine starts. I have never seen this before. What would cause this ?
View 2 RepliesI have a 1986 F150 6 cyl, dual tanks, no AC, manual fuel pump. Just recently, I have been having issues with the tanks. At first it seemed like the back tank was siphoning from the front tank. Now I have fuel coming out of my front tank filler neck. When I open the back tank gas cap, there is enough pressure to spray me with gasoline. I am not familiar with the fuel delivery system of my truck ...
View 2 RepliesOur 2012 camry se had a problem with the fuel pump running when the engine was off. Several hours after we came home I went into the garage for something and heard a humming noise. First thought was a distant neighbor using a leaf blower, then realized it was coming from the rear of car. definitely coming from gas tank area. Turned key on, then off and noise was gone.
View 6 RepliesI have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?
I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.
My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.
So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?
BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).
I got a 4180 carb and at the accelerating pump I got a leak I wound up putting in the wrong screw so I had to retap the hole put a heli coil for 8 32 screw and now that its tight it has a leak don't have a lot of funds right now so I'm trying to find a solution that is not going to cost to much and forgot the count on pri needles and I got a backfire as of right now and not sure what adjustments need to be made or locations of what to adjust. I need to get back to work and its hard to do without transportation.
View 1 RepliesI had a fuel leak at the pump cover (I straightened the cover) and am ready to install the new diaphragm. The old one came out with the rivet head side upward and the pump lever riding on the protruding pin side. Which is correct? This is on an 85 F250 with a Motorcraft carb.
View 1 RepliesI just purchased an 87 f250 w/ a carb'd 460. I purchased it with the mech fuel pump swapped out to an electric. The previous owner states that they gave him the wrong electric pump and I should exchange it for a different one. The reason for him putting it on was to get it running for me to hear it run.
My question: Is this even recommended? I wouldn't mind staying with an electric pump up front. If it is recommended, what would be a suitable pump to replace it with, as in flow/feeding characteristics?
Also, it only feeds from the rear tank, which also has a bad fuel pump. I'd like to get both tanks functioning again. I'd rather not deal with the tank switching valve due to what I've read about them. Has anyone ever hooked up a manual valve and just switched tanks that way? I've searched this site extensively and couldn't find anything. I know I'm not the first to have thought about it.