Ford Ranger / B-Series :: 1987 - No Power After Water Line Broke On Left Side Near Spark Plugs
Dec 22, 2015
I have a 1987 Ford Ranger 2.3L, it's the truck I learned to drive in (stick at 13yo) and the 1st car I crashed too... So now this baby is almost 30 years old and recently had a minor restoration...
Engine was pulled out and all gaskets were changed, spark plugs, wire... All that stuff... It has been running pretty good, however last week a water line broke on the Left side near the spark plugs (if you are looking at the truck)
Since then It has absolutely Zero power. The slightest hill and even when pedal to the floor will lose power. Yesterday went from the start of a hill at 60mph in 4th to 20mph in 2nd because it didn't have the guts to go 1/3 mile uphill... I checked everything I could, and my brother took it to the exhaust guy who made a small hole on the Catalytic Converter and said it was good, but he could tell it was running too rich...
I replaced some of the vacuum lines last night, I found a lose one on the fuel pressure regulator (I think that's what it is, Its towards the engine firewall on top).
Idles beautifully, drives great, no rough shifting, pinging or knocking, no misfires. So that's what has me stumped... Runs great but just no power... Also before water line broke it was running fine with power...
1987 Ford Ranger
2.3L FI
5sp manual, Rwd
View 11 Replies
Advertisement
2004, 4L, sohc - Is there any issues or problems changing spark plugs?
View 4 Replies
Checked icm and is good, replaced coil and still no spark. Issues be gan when about 700 miles ago rotor button broke while driving??? Replaced button cap wires and plugs. Engine fired right up. Ran 700 miles and rotor button broke for 2nd time. This time replaced and will turn over but not crank. That's when I checked icm and changed coil. what should i check now?? 1993 Ranger 3.0 ... Truck has 199,800 miles. Top end was redone at 140,000.
View 10 Replies
One last issue with my 2000 B3000 3.0L. The leak seems to be on the left (passenger) side of the water pump very near where the bottom radiator hose connects to it. I can't find any loose bolts. It does not leak while driving the truck or soon after. It has to sit for several hours or overnight before it shows up. There are usually 3 or 4 wet spots where it drips from the water pump to the frame to the driveway. It is small enough that I only have to fill up my coolant tank every 1 or 2 months. Could this just be a small gasket leak? It's been happening for about a year or so I think. I replaced the radiator about 2 years ago. I've been expecting it to get worse or bust loose and have been checking it very often. I've never seen one not leak while running like this-has me puzzled.
View 6 Replies
I just put an '86 5.0 engine from an F150 2wd pickup in my '87 truck of the same model. The motor was running when pulled but when I set in the '87, it won't run. I've replaced coil, distributor assembly, plugs, wires, throttle body, checked timing etc. I've got spark through the plugs and fuel in the cylinder but with no luck. Don't know where to turn next.
View 3 Replies
I bought a set of Ranger seats for my 1957 Ford project. My question is the drivers side seat reclining mechanism is broke. I believe the seats are out of an STX or sport model, they have a slide out bolster and power lumbar and side bolsters.
Where to get a replacement mechanism. The mechanism works the handle is busted off. It is from an extra cab so the handle is a two way for the driver and or if anyone in the back wanted to use it. I think they may be from a 1992, only say this because I had one backin the day with these kind of seats.
View 4 Replies
1987 ranger 2.9l... My truck had no power while accelerating. We'll I changed fuel pump and filter. And still no power. I bought a computer and it tells me the map sensor is not at normal vaccum levels. The ego sensor is reading always rich. Egr valve not opening. Knock sensor was was going crazy. And computer couldn't raise engine speed above normal idle. Could all this be because of one sensor or should I just change it all.
View 7 Replies
I have a very well maintained 2005 honda odyssey with 150,000 miles on it. It typically gets 22 m.p.g. It started using an unusual amount of gas - was getting 12 m.p.g. Took it to the mechanic and turned out the gas pump was cracked. We replaced the gas pump and the gas line, and it was getting 14 m.p.g. Took it to another mechanic, and he said that the spark plugs were the problem as they were not official Honda spark plugs (we replaced them at around 110,000 miles). So we installed the official Honda spark plugs, but still no good. I have visited several mechanics and no one seems to know.
View 7 Replies
Well it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 Replies
1987 ranger 2.9l 4wd 5 SPD ... I just replaced plugs wires distributer cap and rotor and pcv valve and hose. It drives fine for about 3 minutes and then it looses all power and I can't get out of 2nd gear. It idles fine all day long. The guy I bought it from said he put a new tank and pump on it.
View 3 Replies
My brother's 87 ford ranger 2.3L truck began to have problems. It would be running great, then start to misfire, run rough, sputter, shake and loose accelleration then die. Then it wouldn't start back up for a long time, sometimes til the next day. Little by little, the truck would drive a shorter and shorter distance between breakdowns. He first tried some minor work himself, (basic tune up) - replaced his rotor, cap, plugs, air filter, fuel filter, but that didn't fix it. He went to one garage (big mistake), who said the fuel pump pressure was fine but said he found a broken wire on the harness grounding out and it needed new ignition module and replaced it. (Cost was $350.00+), Garage promised to honor any additional work nec if it continued to have the same problem, and would be free of charge.
Five more breakdowns later and two more "better quality ignition modules", new battery terminals, and 1 new computer later, this joker did more unauthorized work and demanded another $200+ besides the fact of breaking his orig agreement "free of charge" if any further problems! Needless to say, second garage fixed the truck by replacing the magnetic pickup, part # DU 30-C (an electrical part that goes in the distributor and pulsates a current to operate the timing) (it does something like that) and the truck has been driven approximately 40-60 miles as of today, (3 days later), without breaking down. All the other times when picked up from incompetent garage, it wouldn't go more than 1 - 7 miles before breaking down and each time they didn't fix it.
View 4 Replies
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 Replies
I purchased a 2000 Ford Ranger last year. Within the first two months of ownership, the vehicle was having a cylinder 4 misfire. To fix it, I replaced the fuel filter, plugs, wires and cap - replacing the wires, plugs and cap fixed the issue. The issue went away for four months when cylinder 4 misfired again. I brought it to a repair shop and they again replaced the wires and plugs. The vehicle now has a cylinder 6 misfire.
There has to be something causing these plugs to continually go bad. Rather than just replacing the plugs again, I'd like to attempt to be proactive and fix the root of the issue. I've googled the issue and some of the forums seem to indicate a bad EGR valve.
View 10 Replies
I think I've tracked my power steering leak to some type of sensor on the pressure line, close to where it connects to the steering box:
I assume this is a pressure sensor? I got no CEL or anything like that when the fluid had leaked down to the level that the pump started whining pretty badly though. As far as I can tell by looking at pictures, the parts store replacement pressure lines do not have this sensor, or any provision to connect a sensor to it: Advance Auto Parts: Power Steering Pressure Hose by Powercraft - Part 71878
I may just put a replacement line on there and leave the sensor plug hanging and see what happens...
View 11 Replies
2000 ford ranger, 2.5 2wd
Been having a little problem whenever it rains, the carpet on the passenger side gets soaked through and I'm not really sure where the leak is coming from. the only part of the floor that gets wet is the flat part where the passenger would put their feet, but the parts that slope up towards the dash and towards the middle of the cab stay dry. I've pulled up this part of the carpet, and the rubber grommets are intact and in good shape, and there is no rust or anything on the floorboard. from searching here it seems people have had similar problems, one thing being a leak into the seals around the third brake light above the rear window.
a couple things i should mention is that the air conditioning condenser has been broken for about two years, so could water get blocked up and leak in? since its winter here in PA i haven't used the air con since last summer though. I'm not really sure how long the leak has been happening since I've always kept a floor mat over that spot, and the carpet drys in a few days anyway.
Another thing i should mention is that the weather stripping at the bottom of the window on the drivers side door is not perfectly tight and tends to come out of place when the door is closed hard. this has been happening since i got the truck almost three years ago and a new piece was just put in a month ago (the leak had been occurring before the new piece was installed) when the truck was hit and went in for body work. possibly a drain routing to passenger floor? I should add that I'm sure it's not coolant, it has no odor and feels like water.
Might be a good idea to pull up the whole carpet on passenger's side and sit in the cab during the next storm...
View 9 Replies
I have been burning up spark plugs in the left hand cylinder (when facing the engine from the front). I have burnt up two plugs in a month in that cylinder. I have low compression in that cylinder and my oil consumption is high as well (1QT every 300 miles). My question is, is the oil fouling plugs and the oil consumption connected or is there other things I should look into?
View 2 Replies
Whenever it rains a substantial amount, like all day I go out to my 92 Ranger and get in and notice the passenger side rubber floor mat has a puddle of water on it. I look under the floor mat and only the center of the carpet there is wet. I see it's getting the edge of that side of the headliner wet and ruining the new headliner had redone. I didn't realize there was water leaking until I got my headliner redone and put back in. It very well could have been leaking causing the headliner cloth to all tear. It's wet along the top passenger side where the grab handle is and the plastic trim. I thought it was the rain gutter on top of the roof so I put in some black silicone and some of it stopped but not all.
So I thought it was still leaking at the front corner so I put more silicone in. Don't know yet if that was what it was for sure but I'll find out tomorrow because it's raining pretty good right now. But just in case where else could it be getting this much water in. If you go through a carwash, or hose it down for awhile, or even drive while it's raining bad it won't get water inside. I'm not convinced it's the rain channel 100% because on the driver's side the putty filling the rain channel on the roof looks worse than the passenger side and there's no water coming in on the driver's side. There is no water coming in the back or on the back carpet or headliner.
I don't see any evidence around the windshield. I can't understand why only the middle of the passenger side carpet is soaked and not the top or under the seat, unless it's just soaking through the rubber floor mat and not drying out. It's getting so frustrating because I can't visibly find any evidence, I have to wait until it rains and then I can't see why it happens. It's ruining my carpet and my new headliner. I want to replace the carpet but want the leak stopped first. Where are common trouble areas on these 92 Rangers for water leakage?
View 14 Replies
Which transmission came with the 1987 Ranger 2.9L?
View 4 Replies
Have a 5.4l that has multiple issues.
1st, fouled spark plugs on passenger side. All of them have a carbon glaze. That side of the engine seems dead. I checked the pcv valve and its fine. I took the head off to have fixed a broken exhaust manifold screw. After reinstall when The engine started and there was a lot of white smoke from the exhaust. Then it quit smoking. I was hoping it was from the new exhaust manifold i put on, guess not. I took the intake manifold off and noticed that there is an extra hole past the back of the manifold that the manifold gasket goes over but not the manifold itself. The pictures Ive seen make me think the setup is correct, but what is the extra hole for?
2nd, high idling. Around 2000rpm's. I am guessing its because of the right side not working for smoother idling?
View 7 Replies
I have an 87 v6 ranger with 5 speed that has been sitting for several years. The truck only has 48000 miles on it. The gas tank has been cleaned out and both fuel pumps have been replaced. The injectors were pulled and cleaned...
It will start up and run for about 5 minutes and then will shut off. It will not start after that until the next day and then does the same thing. It starts up and runs then shuts off and can't get it to start again. Could it be some kind of circuit breaker tripping or maybe the ecm. If it is the ecm how do you test it...
View 1 Replies
I have a friend who drives a 1987 ranger 2.3 4 cyl and is having problems with oil building up in his air cleaner. I thought maybe it was a bad pcv valve or worn out rings. I looked at it and cannot even find a pcv valve on it. it has one hose that runs from the valve cover to the air clean but there' s no valve in it. are the rings shot or what is causing this to happen?
View 6 Replies
