Ford Ranger / B-Series :: 1992 - Both Power Door Locks Won't Working?
Jul 22, 2014
So I've got this 1992 Ranger extended cab with power door locks and neither side is working. It has power windows too and they work fine. I checked the 30amp fuse under the hood for the power door locks and it's good and checked it with a test light and it's good. What's most likely the cause that both sides don't work? Is there a way to troubleshoot with a test light to trace down the problem as a bad switch or actuator?
View 10 Replies
Advertisement
I'm finally bringing my 99 regular cab to Texas next month and I'm putting together my first list of upgrades to do it. On the top of that list is a remote start system. I am considering installing power door locks so I can install a nicer RS system. It would allow me double my starting distance and take strain off my already bad back since I won't have to lean across the cab to let people in.
View 2 Replies
Just picked up the truck 1995 Ranger XLT. 3L...5spd...4x4...no power windows or door locks. The key buzzer only buzzes for a few seconds, if you move the ignition it buzzes for a few seconds each time its moved. The wipers only work when the buzzer is dinging. Also..the wipers when turned off stay in the up position. I replaced the ignition key mechanism and the on off wiper relay. What am i missing in this weird scenario??
View 1 Replies
Will a driver door from a 92 ford ranger fit a 93 ford ranger?
View 5 Replies
Having problems with their door locks attempting to activate when turning the ignition key? If so, how can I correct it or make repairs.
View 3 Replies
I have 92 ranger with 3.0 v6 in it.
It flashes out code 212 ive replaced the ICM and checked the spout connector for corrosion but it still flashes out 212 and has a rough idle no power on acceleration condition.
also when the idle starts acting up the check engine light stays real dim and if you rev it it will get brighter
View 3 Replies
1992 Ranger 4x2 with 2.3L stick shift no AC no power steering. Recently the temp gauge began fluttering in the cold range from far left to just below the normal range. The defrost and heater blows only cold air. I had a professional shop radiator flush done. No change. I changed the engine thermostat out for a new one but no change. The upper radiator hose feels hot, so I assume the thermostat is working.
Questions: Where is the temp gauge sensor located on the engine? Is there another sensor or shutoff before the heater that might not be working? Where do I take things apart to check if the heater blend door is working?
View 1 Replies
Troubleshooting a problem with friend's 2000 F250. His power windows aren't working and are causing problems with his door locks and interior lights. When he tries to use his drivers side power window, his power door locks quit working. If he puts the switch to raise, the interior lights flash. From what I've read, it sounds like the GEM to me, we've inspected the wiring and it all looks good. I pulled it out today and it looks good inside, no sign of water leaks on it. If it is the gem, how much do they cost and do they require programming?
View 5 Replies
Vehicle: 2002 f250 xlt 7.3 powerstroke reg. Cab
Issue: door ajar light stays on, power locks on driver and passenger door don't work, radio stays on after truck is off an door is opened.
Events leading up to issue: went to temporarily hook up a wolo dixie horn to see if it worked. Wanted to do it fast so I took + cable, tied one end to the battery terminal and then connected other end to dixie horn relay. I then grounded both negative wires to the truck. One ground on the frame the other I temporarily wrapped around a one of factory ground mounts under the dash. Immediately after doing this the problems stated above started.
How can I fix this. I need to fix this by tomorrow. I have a guy from Craigslist coming to look at the truck. Now the 4x4 issue.
Truck has zf6 manual and the electric 4wd select ****. Just thought I'd list this if it was needed to be known for solutions.
4x4 high light stays on in while 2wd all the time. 4 low will stay on after switching back to 4 high and 2wd but it goes out if I ether stop the truck shut it off then restart it. or back up and slam on the brakes. Also when in 4 high the front driveshaft won't spin. However It will spin when in 4 low.
Another random issue I'd thought I'd just list while I'm writing this.... Cruise control does not work. And when I press the "on" button and the "coast" button at the same time the horn honks.
View 3 Replies
I have a 1992 Ranger with 2.3L that suddenly lost power on freeway and stopped and couldn't restart. Towed it to Seattle, WA and need Ford Ranger 2.3L engine mechanic to double check the timing since new belt installed to make sure it was done right before cover and rest of engine reinstalled.
View 5 Replies
So on my 2001 excursion v10 my power door locks won't work. The 30amp fuse under the hood is blown and originally thought it was simply the fuse. No biggie picked up a new fuse... yay it works! Well it did for 2 locks and 2 unlocks then blown. So after reading I suspected it was the resistor inside the door lock actuator. So I did the free mod (taking them all apart and using foil instead of a resistor) got done last night popped in a new fuse... 2 locks 2 unlocks and a blown fuse. So I feel like I wasted a bunch of time doing the resistor mod but whatever,and now im back where I started. So right before this problem started originally one of my boys was messing with the number pad on the driver door. Not sure if its related just thought I'd put that in for out there.
View 7 Replies
1992 Ford Ranger 4x2 with 2.3L engine and 5 speed manual transmission. 135,000 miles, no AC and no power steering. I am having poor clutch disengagement and resulting hard shifting. The shop added a little fluid to the reservoir last oil change and it is still looking full. I always park on concrete and never see any leaking. I don't know what may have been done before as I haven't had the pickup all that long. Where should I start? Is there probably internal bypass leaking in the hydraulic clutch as there seems to be no external leaking?
View 4 Replies
I have a 2002 f150 supercrew, 4wd. The power door locks stopped working the other day and I am trying to fix it. So far I have checked the fuse in the power distribution box, good. I have checked the wires from the doors to the cab along the door sills to the rear doors , all good. I did find a couple of iffy grounds on the left kick panel and cleaned and repaired them. I am having a heck of a time finding the group of relays that control the lock and unlock functions. Remember , I have no power lock function at all. I would swear its not getting power to the relays but until I find them , I just don't know. Where they are supposed to be?
View 5 Replies
1997 Ford Expedition 4x4
When I push the switch for the drivers window I can hear the relay in the fuse block make a click but window doesn't move. If I push the switch for any other window (on the drivers door or any other door) no click at the relay and no window movement. I've swapped the relay with other relays in the fuse block but nothing changed.
I've tested the driver side window motor by running 12 volts directly and the motor works fine. When I press the PDL switch I hear a buzzing sound coming from the passenger floor area behind the glove box but the locks do not go up or down. I started the truck and when I put it in gear I can hear the PW relay in the fuse block clicking repeatedly. Put the truck in Park & the clicking stops.
I was told (on another forum) that the problem is most likely my GEM module. Bought a used 1 on eBay and installed it today but nothing changed.
View 7 Replies
2006 F150 5.4 2WD extended cab tow package 24k miles
My power windows have stopped working from all locations. I checked and the fuses are good. I can no longer use the exterior keypad to unlock the truck, yet my remote keyring switch will electronically open both driver and passenger doors. Neither driver's nor passenger's interior door switches work.
View 7 Replies
Power door locks on my 2001 Aurrora have stopped working. It seemed to progress. First the rear door locks didn't work, now the rear and passenger door locks won't open or close with key fob or power switch on doors. I can still operate the door latches manually with the door lock lever. Also the interior lights and power windows to these same doors don't work. I examined the fuses under the rear seat and found nothing blown. What controls all these devices? The driver door operates as normal.
View 14 Replies
I have a 2000 Taurus and recently the power windows and power locks stopped working. They won't work from any door switch but when I use the key fob to unlock or lock the car the locks will work. However, the windows won't work from any door switch. I didn't see a fuse marked for the windows or locks.
View 3 Replies
I have a 2003 jetta GLI (vr6 6 speed) that i received from a friend because of some body damage to the doors mainly. so i replaced the doors with some from a 2001 jetta glx, but the power windows don't work with the switches inside the car. However, when I put the key in the door and turn it, all of the windows will go up and down...(So the motors are good and they are getting power) the door locks, gas cap lid, trunk, sunroof all work and the interior lights work as well.
So i researched it and everyone said fuse #14 or ccm... so i replaced the fuse.... multiple times now just to make sure... After that didn't work, i bought a new ccm with the same part #. that didn't work at all... still same problems... I was wondering if maybe the new doors are or aren't CAN-BUS? if that even matters?
View 4 Replies
Since yesterday the power door locks on my '98 Accord LX (Sedan) are not working. I noticed that it happened after I started the car and it died on me. I tried it again but this time with my foot on accelerator and it started fine. I started driving and then noticed the locks weren't operational. They were fine before this episode.
- When I press the power door lock button on driver or passenger side nothing happens (usually it locks all four doors)
- Manaul locking is fine
- When I lock the car with key it doesn't lock all the door (it only locks the door I'm at - driver or passenger). This is supposed to lock all doors too.
I looked at the interior fuse box on Passenger side and the door locks fuse looks ok (#12). I also swapped it with passenger side power window fuse and the window still worked so I guess it's fine. what I can look at next? I read the the actuator might be a problem (I don't know what it is but I'm willing to give it a shot). Looking at Honda Manual looks like there are multiple actuators (one per door I think) and it doesn't feel like everything would conk off together.
View 4 Replies
I've searched the inter tubes, trying to find out if there is a fuse or relay or even circuit breaker that needs replacing. From all I've checked, I can't find a fuse, relay or circuit breaker labeled to control window and door locks.all 4 windows don't work (with exception to front passenger window occasionally goes down but not up.)finally figured i should have come to this fine forum first! (especially after hearing 'car talk' today)some other pages with similar questions had answers referring to fuse #12 or relay F (mine aren't identified that way). I'm heading out to get a test light -- just so i can see if i can test anything...
View 13 Replies
My newly purchased 1999 b5 passat wont lock/unlock with the key. The key does nothing and i dont have the flip key, i want to get a new flip key from the dealer but i am unsure if they can code it to my car if the lock dosent work i took the door panel off but didnt want to take off the inner metal skin to figure it out.
View 9 Replies
