Ford Ranger / B-Series :: 1995 XLT - Overdrive Light Is Not Working And Button Does Not Respond
Apr 30, 2016
I just bought an older 1995 Ranger XLT 4.0 I was told that the truck is stuck in overdrive. The overdrive light is not working and the button does not respond. It shifts smooth but run away with it's self. It is not shifting a lot going up hill and curves.
I got a diagnostic and it did not show codes. I was told the trani has had an oil change and filter with no metal parts in the oil. Since the overdrive switch is know for a short in the steering column maybe when they looked at it they did not know what they were doing.
I am driving it only once or so a week. But don't want to hurt it. A friend did the first work and had it diagnostic done yesterday.
View 14 Replies
Advertisement
I have a 03 ranger with a v6/auto trans. it drives fine around town. after i get on the freeway the overdrive light will start flashing. when i get off the freeway it will shift extremely rough. if i turn the truck off and right back on it will be fine again. What could be the problem?
View 5 Replies
1995 ranger 4,0 4x4... when started up, wipers go 2 times and then stop, but cant turn on again, also blower and 4WD stopped work....
View 4 Replies
I have an 87 Ranger and the oil pressure gauge is slow to respond changes in pressure. Is this the way the gauge is designed to work or do I have a bad sending unit?
View 4 Replies
So i just bought a b4000 pickup 5spd .. Anyway the truck has eletrical 4x4 with manual hubs. When i turn the switch nothing happens. The 4wd/4wd low lights both flash 6x then go off then flash again while running , driving, koeo, anytime like an obd1 check engine light code flashing. Anyway i checked the wiring for the 4wd switch no power, went to the fuse interior no pwr, went to the engine fuse box power. You don't hear the transfer case engage at all as well.
View 5 Replies
I have a 97 f150 2wd 4.2. my speedo is working on and off, my overdrive button is flashing and its shifting terrible. I changed the vss in the top of the rear diff but no luck... is there another sensor I should change? or go back and start looking at the wiring to the on in the diff. she has 353k on her and was running great till this.
View 6 Replies
Last year I bought a used '99 F350 w/ ~$135K miles on it. I later noticed that when I pressed on the Overdrive button (automatic transmission) which is on the steering column gear change lever, nothing happened. The overdrive light did not come on and the gear did not change to overdrive.
View 11 Replies
2002 Escape. The over drive deselect button stopped working on my wife's escape. Is their a fuse other than the box under the hood? Transmission was rebuilt not too long aga and has been running fine till the other day.
View 2 Replies
I went to transmission shop today and tech told me c solenoid was showing performance problem when scanned. He took it for drive and said it was commanding shift into fifth gear. It is a 3.0 extended cab 2wd with just over 200000 on truck, transmission was rebuilt just over 25000 miles ago. Fluid is so clean its still clear looking just faint red color. All other gears shift and pull great all electrical clean and hooked up, he crawled under it and said pan adjustments were tight, whatever that means.
View 14 Replies
I've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
View 14 Replies
I have the infamous ABS light & speedo not working on my 2000 Ranger. I replaced the ABS Speed sensor on the rear diff as has been suggested on many posts, but it didn't solve the problem. Did I get a bad part or is there something else I should go after?
View 7 Replies
I have a 1988 FORD Ranger with the 2.9 liter engine with the four speed automatic overdrive transmission. Several days ago the transmission went out. The truck will not pull in reverse, overdrive, drive, second or first. Usually most vehicles will usually have at least the reverse, A first or second when the drive and overdrive stops working altogether. What the problem could be?
View 1 Replies
I have a 1999 mazda b2500 and unable get my dome light to work. Replaced the light bulbs so not issue.
Issue #2 When I start truck I get 5 beeps for 5 times and after truck running for extended periods beeps again.
How do I repair these issues?
View 3 Replies
I have a `95 explorer with the 4.0 motor. The electronic overdrive off indicator light (O/D Off) on dash started flashing today. The transmission seems to be shifting into overdrive. Owner's manual says to have it checked as damage can be caused. What I should be checking?
View 11 Replies
My tranny started acting up so I took it to a reputable transmission shop for repair.
Symptoms : Shifts very hard 1st to 2nd. Light flashes on overdrive button.
The following is what has been done at the transmission shop.
Computer failed to read codes. Sent out to rebuild. After rebuild, codes read FIPL needs replace. Done and gives good readout. Trans control replaced, speed sensor replaced, checked all associated wiring and plugs as well as ground. Dropped pan, changed fluid and filter. No parts in pan. Tech says pan and fluid looked good. Replaced coil pack.
After all that, this is what is happening..Clear all codes. FIPL reading good. No flashing light on shifter. It feels like it is shifting from 1st to 3rd, then back to 2nd. Still shifting hard and indicator light starts blinking again. He is going to read computer again. At this point, he suspects a mechanical problem in transmission but is reluctant to remove and tear down.
View 7 Replies
The air bag light stays on & the blower in not working. I checked the fuses good.
View 2 Replies
I have a 1995 Explorer 4x4, and starting last month i have been having an intermittent problem with bang shifting, the only time the bang shifting occurs is when the overdrive off light flashes, the only time the O/D Off light flashes is after driving the interstate or driving around town on hot days, after a few days or a few weeks the light turns off and its shift normal and no bang shifting, but i have a new problem now, the O/D Light off started flashing last night after driving the interstate and I noticed on my way home that it wont shift, it hit 4000rpm and i had to tap the break and accelerate again to make it shift, I went to AAMCO and they wont give me the codes the only thing they said is they want to do a soft parts rebuild, and something about hte gear ratio being off, i dont have the money to spend for a new trans or have one rebuilt, i would like to fix this myself.
View 14 Replies
Not sure the problem is related.
The horn no longer works. The air bag light is on, on the dashboard.
I have checked all the fuses and they appear to be good.
How would I diagnose this problem?
View 7 Replies
What is the likely culprit? No other electrical issues, brake light quit working when brake is depressed, all other lights work including blinkers/running/head. Was going to break out a wiring diagram....
View 7 Replies
I noticed the passenger side on/off switch for the airbag doesn't illuminate anymore on my 98 Ranger. Whether I turn the key on the switch to on or off it doesn't illuminate either way. The airbag light on the dash flashes showing, counting a code 27 and then it stays on. I also noticed the seat belts on symbol doesn't illuminate and in the owner's manual it says it should illuminate and chime. I remember it use to illuminate but I don't remember a chime.
Someone with a 98 that has a seat belt reminder light that illuminates and chimes until you fasten the seat belt? I don't know if that and the airbag code is related. But I want to fix both? I guess the simplest one to tackle first would be the seat belt light/chime. I don't see a fuse for it. I guess I need to know first is it really suppose to chime.
View 12 Replies
1995 Ford 4.0 ... All the following have been replaced on the truck.
High Pressure Fuel Pump and assembly
Idle Air Control Valve
Spark Plugs
Oxygen sensor (Bank 1 sensor 1 Oxygen)
Fuel Filter
The most recent item that I replaced is:
Coil Pack
Spark Plug Wires
Now, with the Coil Pack replacement, the truck drives good, as long as I do not floor it (After it heats up, about 15 minutes). Basically, if I try to pass someone, the truck acts as if it is chocking out, like it is not getting any fuel.
Before replacing the Coil Pack. It would chock out at any given time, rather just barely pressing the gas peddle, or just sitting idle.
I took it to a friends muffler shop, and he stated that it is not the exhaust that is causing the issue. I am at a loss. Is there anything else that I can check?
The truck seems to drive fine, as long as I do not get down on it, and try to take off fast after it heats up. When it is cold, I can take off like a bat out of hell, and it runs like no-ones business.
View 14 Replies
