I have the infamous ABS light & speedo not working on my 2000 Ranger. I replaced the ABS Speed sensor on the rear diff as has been suggested on many posts, but it didn't solve the problem. Did I get a bad part or is there something else I should go after?
View 7 Repliesso heres whats happening. My 98 ranger speedometer has not been working since I owned it (I am the second owner who got it from a grandpa) and I've replaced the vss sensor two times, got a new connector and gave that a try and still nothing. Yes I've looked for cracks in the wire or any exposed copper, I've looked through many forums and cant figure it out. At first before replacing the vss, my abs and check engine light weren't lit up until i put a new vss sensor on that i got from o'reillys, so then i got another one thinking it was just a bad sensor and still no luck. another thing is when its cold in the morning and i get in my pickup to go to work it will start working once i go over 30 and fluctuate between that and 20 but if i don't accelerate it will not bounce all over the place.
View 4 RepliesI have '90 Ford Ranger 2wd standard cab long bed. A few days ago the speedo stopped working. What is the more likely cause? The gauge itself or a relay/cable. And if it is the cable/relay are they hard to remove & replace.
View 1 RepliesI have a 2000 ford ranger 4.0L v6. My problem is the abs light stays on and the speedometer won't work till i hit about 35-40mph.
View 14 RepliesLast night the speedometer started acting up, would fluctuate when the truck went over bumps and completely cut out on moderate right turns. Looked underneath as well as one can in the dark and couldn't find anything loose.
This morning I searched on here and the VSS came up numerous times as a common failure. $15 and about a half hour later I had it installed, and while I was under there I took a better look at the other connectors to double check harness connections for tightness and cleanliness. It all looked good, so I went ignition on... and the light came back. Tried clearing it by keeping the diag connector unplugged while switching ignition off, but no go. Took it for a quick spin around the parking lot, and the speedo was completely dead.
Hit up my factory ETM, found all the relevant connectors and set up a wiggle test of the VSS circuit with the DVOM on audible continuity check. Found one of the wires had chafed against the body right by the under-cab harness connector and worn almost completely through. Cut out the bad bit, soldered and heat-shrunk a patch in, and took it for a spin. Voila! No more ABS light and a working speedometer.
Also fixed the fuel gauge sending unit wire which was in the same connector grouping and chafed (but not yet broken) in a similar manner.
Sold my mazda and got a nice 2000 2wd Ranger XLT with a 3.0L. Today the wife I and took it to town, 10 miles on the highway there, a couple in town and 10 back, didn't notice anything unusual. However I haven't this truck long so I'm not sure what is usual.
Parked it for a few hours and when went out to change the front turn signals to LED I noticed the ABS light was on when I drove it into the garage...
I checked fluid, connections and fuses, no change.I go ahead and swapped the bulbs while letting things simmer, I've had so many of these Fords sometimes the easy fix comes to me.
I backed it out and took it down the road, right away I noticed my speedometer wasn't working, so I let off the gas, when I re-applied the pedal I got nothing, like it was in neutral.
I downshifted to second and got her down and turned around as the O/D started flashing... (so glad because I would have hated walking back), then pulled her back in the garage to check transmission fluid and recheck fuses, including the ones I forgot earlier under the hood. I added a 1/4 qt of fluid then tried a road test again, this time there was a real long pause before it upshifted hard and the CEL came on.
I pulled the codes with my scangauge and got:
P0500
P2120
P0028
And decided I better look some things up and consult the gurus here before I do anymore damage tonight. I'm guessing that I'm looking at a tranny replacement possibly, but with the ABS light and speedometer failure I'm not 100% sure what is going on here...
Recently the ABS light came on (truck does not have ABS), also speedometer quit working and trans was not shifting right. After a few minutes the problem went away.
View 4 RepliesI lost the windshield wipers, speedometer, dome light, door alarm. Check all the fuses I can find all are ok. Whats wrong.
View 7 RepliesI have a 1999 mazda b2500 and unable get my dome light to work. Replaced the light bulbs so not issue.
Issue #2 When I start truck I get 5 beeps for 5 times and after truck running for extended periods beeps again.
How do I repair these issues?
The air bag light stays on & the blower in not working. I checked the fuses good.
View 2 RepliesI just bought an older 1995 Ranger XLT 4.0 I was told that the truck is stuck in overdrive. The overdrive light is not working and the button does not respond. It shifts smooth but run away with it's self. It is not shifting a lot going up hill and curves.
I got a diagnostic and it did not show codes. I was told the trani has had an oil change and filter with no metal parts in the oil. Since the overdrive switch is know for a short in the steering column maybe when they looked at it they did not know what they were doing.
I am driving it only once or so a week. But don't want to hurt it. A friend did the first work and had it diagnostic done yesterday.
1999 (built late 1998) Ranger 2.5 stick 2wd single cab. If I get much over 75 MPH the speedometer will reverse direction despite increasing speed. If I then let off the throttle completely, the speedo will jump right back up and indicate the correct speed. Continued operation without letting off the throttle to let the speedo recover will trip the ABS fault light, probably due to the erratic signal.
Disconnecting RABS module has no effect on symptoms. Speed sensor in the rear axle has been replaced already (by me) and the new unit ohm'd out good. Wiring between GEM and sensor checks out as well, good continuity (< 1 ohm) and no shorts to chassis ground. I wish I had an o'scope to take a look at the waveform, but I don't at the moment. It is on my future tool purchase list.
Not sure the problem is related.
The horn no longer works. The air bag light is on, on the dashboard.
I have checked all the fuses and they appear to be good.
How would I diagnose this problem?
What is the likely culprit? No other electrical issues, brake light quit working when brake is depressed, all other lights work including blinkers/running/head. Was going to break out a wiring diagram....
View 7 RepliesMy speedometer does not work. Also, my 4wd high light is on but not engaged. Are the two related? I've looked up speed sensor and it's separate from the actuator for 4wd. Maybe coincidence they stopped working simultaneously? Should I start with the speed sensor?
View 1 RepliesI noticed the passenger side on/off switch for the airbag doesn't illuminate anymore on my 98 Ranger. Whether I turn the key on the switch to on or off it doesn't illuminate either way. The airbag light on the dash flashes showing, counting a code 27 and then it stays on. I also noticed the seat belts on symbol doesn't illuminate and in the owner's manual it says it should illuminate and chime. I remember it use to illuminate but I don't remember a chime.
Someone with a 98 that has a seat belt reminder light that illuminates and chimes until you fasten the seat belt? I don't know if that and the airbag code is related. But I want to fix both? I guess the simplest one to tackle first would be the seat belt light/chime. I don't see a fuse for it. I guess I need to know first is it really suppose to chime.
1998 Ranger... I started having Speedometer/odometer problems after a power surge when my alternator went out. I knew the alternator was going bad and I tried to limp home another 5 miles rather than pay a tow bill and the alternator overcharged for a few seconds before completely dying. Since that time the only problem I am left with is my Speedometer and odometer have not worked. Scan tool says p0500 and I have replaced the ABS sensor on the differential with an OEM part but still no speedo or odo. I have checked all the fuses and relays associated multiple times. I do suspect that the RABS resistor is bad but there is no ABS light and it doesn't make sense that this one resisitor is the sle key for the whole speed control circuit. It's a manual transmission and RABS only. I swapped out the Cruise Control Servo with no luck as well. I am running out of options before having to take it to a dealer because I have to pass inspection. I have also checked and there is no power coming to 679 (GY/BK) into the instrument panel. I have also checked continuity for the rear harness to the ABS sensor and it is good.
View 2 Repliesso i changed the speedo cable and speed sensor in my 93 ranger, but still getting the speedometer bounce. what could be next? the speedo housing in the cluster? lubed the inner cable, made sure nothing is kinked or sharp bends. Put in a new vehicle speed sensor while i was at it just bcuz. cruise control does not hold a steady speed either but i think the 2 are not related. I'm leaning towards the cruise control servo as to why it does not hold a steady speed. Most of the time once i get to around sixty i'm basically driving by ear bcuz the speedo bounces from 60down to 55 and back up.
View 3 RepliesOn my '91 last week I was driving on the highway about 60-65 when all of a sudden the speedo dial started climbing to 70-75-80-85 and past. The odometer seems to be working ok? Still when I drive it still operates in the same manner. It never bounces around or falls back. The needle is sort of stable such if I maintain a speed the speedo will maintain even though it's incorrect. There is a slight wavering of the needle meaning it's not as stable as it use to be. With the odometer working I was wondering and don't know. Does the cable drive the needle or is it electrically controlled? I'm thinking of grabbing another instrument cluster it that is the problem, I'd like to know more about it and understand how it works so I don't just throw parts at it until it's fixed.
View 1 RepliesI have a 1999 Ranger 4x4 4.0 5 speed step side...in Jalapeno no less. Anyway, for the past 5 years or so the check engine light has been on. When it came on I did nothing because nothing seemed to change and I was too broke to fix it anyway. Well, just lately the check engine light has started to flicker or go out completely.
When this happens the truck seems sluggish and the A/C will stop working. As long as the check engine light is ON the truck runs like it always has, when it goes off the issues start. If I am stopped with the clutch depressed the idle will drop down to 500 rpms or so.
Kinda hoping it is something I can fix or at least learn about so I can have an intelligent conversation with a mechanic.
I have a '97 Ranger 4.0 4x4 5 speed, as the title says... my radio does not work. It has an original cd radio and I had installed an aux cord. After I installed it I could only get a select amount of radio stations, last week I had went out of town so I didn't drive it at all, I came back and there was what seemed to be no power to the radio at all. No display, no sound. Only the lights on the radio controls (pre-sets, volume, seek, etc.) I have checked the fuses, pulled the radio and checked everything from behind and still nothing. Could the radio its self be bad? What else should I check?
View 1 Replies