I have '90 Ford Ranger 2wd standard cab long bed. A few days ago the speedo stopped working. What is the more likely cause? The gauge itself or a relay/cable. And if it is the cable/relay are they hard to remove & replace.
View 1 RepliesOk, I own a 1990 Volkswagen Jetta GLI that I bought from my neighbor about 4 months ago, and recently, it started having problems. It's idling very high, around 1,500-2,000 rpms, it's leaking coolant, not from the bottom of the reservoir but from the top, and it's slightly overheating. Oh yeah, the speedometer stopped working. I've recently taken it to the shop twice, the first time to get the reservoir replaced, and the second time to get radiator replaced.
I have had problems with it stalling in the middle of the highway during traffic because it over heated. I commute daily to and from college and I want to make this car last as long as possible as I do not have the means to buy a new car. I have noticed that there seems to be a build up of air in the reservoir. I witnessed it leak, and there was a hissing sound coming from it. Also with the speedometer, the light doesnt turn on for it and that there is a clicking noise coming from it. Any tips?
Just picked up a 90 Ranger last night, 4.0 EC, good ole A4LD, from a recipt I found has 70K or so on rebuild, was driving it today and the TC unlocked, and now it won't lock back up. I checked fluid and it was a little low, topped it off and drove it, and it was the same thing. I'm kinda new to thease A4LDs I know they can have issues, but can be good too. Just want to know whats going on so I can fix it! No codes were found when I scanned it. Trans otherwise shifts fine, you can feel it go into OD but no lockup.
View 13 RepliesI have the infamous ABS light & speedo not working on my 2000 Ranger. I replaced the ABS Speed sensor on the rear diff as has been suggested on many posts, but it didn't solve the problem. Did I get a bad part or is there something else I should go after?
View 7 Repliesso heres whats happening. My 98 ranger speedometer has not been working since I owned it (I am the second owner who got it from a grandpa) and I've replaced the vss sensor two times, got a new connector and gave that a try and still nothing. Yes I've looked for cracks in the wire or any exposed copper, I've looked through many forums and cant figure it out. At first before replacing the vss, my abs and check engine light weren't lit up until i put a new vss sensor on that i got from o'reillys, so then i got another one thinking it was just a bad sensor and still no luck. another thing is when its cold in the morning and i get in my pickup to go to work it will start working once i go over 30 and fluctuate between that and 20 but if i don't accelerate it will not bounce all over the place.
View 4 RepliesI have a 1999 Ranger 4x4 4.0 5 speed step side...in Jalapeno no less. Anyway, for the past 5 years or so the check engine light has been on. When it came on I did nothing because nothing seemed to change and I was too broke to fix it anyway. Well, just lately the check engine light has started to flicker or go out completely.
When this happens the truck seems sluggish and the A/C will stop working. As long as the check engine light is ON the truck runs like it always has, when it goes off the issues start. If I am stopped with the clutch depressed the idle will drop down to 500 rpms or so.
Kinda hoping it is something I can fix or at least learn about so I can have an intelligent conversation with a mechanic.
I have a 91 Ranger that the A/C was working great in but all of a sudden it stopped working even the fan. I turned it of and back on and it started again but then just stopped for good I can get the fan to work sometime, but no cold air. What it might be?
View 2 RepliesMy brother has a 99 ranger with the 4.0 engine and factory tow package. After installing a rebuilt engine the brake lights do not work and the turn signals will blink both sides like flashers. Lights on the truck work fine. What connections may be hooked up wrong or where to start looking for the problem.
View 3 Replies1995 ranger 4,0 4x4... when started up, wipers go 2 times and then stop, but cant turn on again, also blower and 4WD stopped work....
View 4 RepliesI recently got a pretty cherry 98 Ranger 3.0 2wd extended cab auto. So far all it has needed was wiper blades, floor mats and a heater blend door. Last week my daughter informed me that the flashers and the turn signals stopped working. I looked for blown fuses and then took the low road and just bought a new flasher (my alldatadiy manual showed that the flasher was common to the turn signals and the hazard flashers so I took a shot at just throwing a part at it). That didn't fix it or else. Any pointers?
View 3 RepliesNot sure the problem is related.
The horn no longer works. The air bag light is on, on the dashboard.
I have checked all the fuses and they appear to be good.
How would I diagnose this problem?
I noticed that my turn signals stopped working. I replaced the flasher. Now the turn signals work but the signal indicators in the dash don't light up. Also, the hazard lights don't work either. No flashing, no blinking when I turn on my hazards. I've seen many variations while searching? 1994 B3000 2x4 extra cab.....
View 14 RepliesI recently acquired a 4.0 Ranger 4X4 Auto for my use in Costa Rica. It runs fine but it'll illuminate the CEL within a few seconds of starting and whenever revs fall below approx 1000. When pulling off the line or accelerating, the light will go out but comes back on when the throttle closes. The previous owner has replaced the MAF and idle air valve. I've corrected a lot of issues with the vacuum system and think it's back where it ought to be. I know I am going to need to pull the codes but I'm back in Dallas now and can't do it yet. Need general list of affected parts that I could buy here and take back down.
View 14 RepliesI got a 1990 Ranger 4x4 2.9l that loves to get hot only when the ac is on. The engine was rebuilt by me about 2000 miles ago and I made sure to have the block boiled in order to clean out any crap that could've been built up in the water jackets. So far the radiator, cap, thermostat, and fan clutch have been replaced. The fan shroud is intact and the condenser has a few bent fins but not many.
Here in Vegas we're looking at 100+ from 10 am - 4 pm so the ac is a must. I could be sitting at a light all day with the ac turned off and the truck doesn't have an issue. When I turn the ac on though the truck almost immediately begins to get hot. The engine drops maybe 100 rpms and the voltage gauge also drops a little. At night if I'm running the ac the voltage drops to what looks like 10 volts.
While the ac is on there is an immediate loss of power as well. In my head I'm thinking a failing compressor, water pump, and alternator are at fault. It doesn't matter if the truck is moving either, the temp still climbs.I know the rangers are funky with their cooling so when I burped the system i turned the heater on and lifted the front end about 1 ft off the ground with the cap off.
1990 ranger 2.9 ... I have put about everything new on this ranger. It has no spark, ran fine til i went across a set of railroad tracks, it died 6 months ago and never started again .. Many dollars and many hrs has gone into this thing and still no spark. It will spark when you turn the key on. Crank it and 3 more sparks and thats it. Every electrical piece has been replaced. I've checked and bought relays ,fuel shut off, new distributor pickup coil, rotor, cap, wires, plugs, coil and still no start?
View 6 RepliesI have a 90' Ford Ranger, rear wheel drive.
I can not find a 2 wheel drive automatic transmission and I was wondering if I can convert a 4 wheel drive transmission?
Mine has a strange issue. 1990 xlt 2.9L manual 4x4. When first start of the day, after start I push accelerator and it has a hesitation like not getting fuel. Where start?
View 1 RepliesI've got a 1990 ford ranger 4.0 auto trans front transmission seal went bad, I've got everything unbolted abs ready to come put but the trans won't come over top of the front cross member, what could be the problem on why it won't come out?
View 3 RepliesIs there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?
View 1 RepliesMy 1990 4.0 refuses to start when the air temperature outside is at approx 40 degrees or below. It will crank until the battery runs dead if I let it. At approx 50 degrees farenheit the truck takes forever to start and always backfires out of the tailpipe and intake manifold (blowing off a hose on the vacuum tree) before it starts. If I can get it to backfire, it will start eventually. If it does not backfire, then I can run the battery dead and the truck still refuses to start. This condition has grown from a little problem to a huge problem over the past 6 months. Here is what I have done so far, including regular maintenance items.......
KOEO test checked OK
KOER test returned code 77 multiple times (TPS).
Replaced Throttle pos. sensor
Replace Idle air bypass valve
Subsequent KOER test came back with no more codes except 11 - OK
Load tested battery
Made new heavy gauge battery cables for + and -
New plugs, wires
newer starter
Changed coil pack for known good one off my explorer
Visually inspected hoses for vacuum leaks, replaced 1 cracked hose
1990 Ranger ext cab 4X2 4.0L, K&N air filter in stock airbox, Pacesetter headers, single 2 1/2" exhaust, stock cat no muffler, 260K on truck, 104K on good used engine from my 1994 Explorer. Purchased Ranger brand new in 1990. A4LD w/ shift kit.
]I recently bought a 1990 ford ranger with a 2.9 @187,000 miles. That being said I went through and changed a few vacuum lines, the oil, air filter, pcv/grommet, and fuel filter.
The problem is it hates to start. I could crank on it for 10 seconds and not a single thing. Sometimes if i turn the key to the off position, wait a second, and try again, Ill get the truck to fire. When it does fire up it just reeks of the lean exhaust. It also gives me some hesitation when I rev it. I did a fuel pressure test (KOEO) last night and it gave me 32 psi and within a minute the needle fell to about 25 psi. I hear the fuel pump run for only 2-3 seconds too.
I've already pulled the MAF off and cleaned it, replaced the TPS, and did a fuel pressure test. The fuel filter is brand new