Ford Ranger / B-Series :: 1997 - ABS Light On Steady And Never Goes Away
Mar 10, 2013
1997 ford ranger 2.3l ...
I have my ABS light on steady and never goes away. This all happened when I had a friend work on my truck. Long story short, it seemed like lost the RABS diode under the hood and replaced it with a 'hacked' 7.5amp fuse. I saw this and was very disappointed.
So I first changed the speed sensor and nothing. I did the RABS code test and received 12.
My questions is whether or not that hacked fuse is causing all of this, and if it can cause long-term damage to the electrical system. I don't mind non-abs at all, but more on the long-term affects.
View 5 Replies
Advertisement
I have a 1997 Ranger with a 3.0 v6 with a super high idle.
It idles at 2500 RPM when the IAC is plugged and a steady 1100 when unplugged. I have replaced the IAC twice now (dropped the first replacement. long story) and and have also checked for vac leaks with no results.
After about 2-3 minutes of idling at 2500 on a cold start it will drop down to 1100 (same as when IAC is unplugged), but after a 10 minutes or so drive it will idle steady at 2500 with minimal if any dropping in RPMs. This is driving me crazy not only because it sounds horrible but also because of the fact it's burning through fuel like it's going out of style.
I have checked the MAF sensor and it looks brand new (not the original owner) along with the O2 sensor. I have been meaning to check the TPS voltage to see if it's working correctly but without a working multi-meter it's making it difficult to do anything.
I'm at a loss with this right now and because of all the previous repairs i have done to it and the others that still need to be done i don't have the biggest budget to fix this problem nor the money the truck is using in gas.
View 14 Replies
This interference correlates directly to tire rotation speed, engine rpm has no effect. Under about 5mph it won't make the noise, but over that you hear a pop more or less for every rotation of the tire and when you hit say 50mph it is just a steady static noise on AM only. Haven't pulled the head unit yet, checked several body grounds under the hood and all are good. Don't know if a damaged wheel sensor could cause an issue or not.
View 4 Replies
I have a 97 Ranger with 4.0 V6 with about 120,000 miles. The battery light came on today so I took it to Advance Auto to check the battery and Alternator. They said both were good. I checked the fuses and relays and nothing was blown or out of place. Could it be a bad ground?
View 8 Replies
1997 Ford Ranger Manual. The blinkers are on and light up they'd just don't blink . Don't know what to do all fuses seem to check out.
View 2 Replies
I just finished replacing the instrument panel light bulbs on my 1997 Ranger XL, 2.3L, 2WD pickup. I wanted to share how I did this. First of all, if you never have done this before, go slow and take your time removing the dash panels as they are plastic molding and break easily. Allow yourself about an hour to complete the task. You will need smaller sized hand sockets to remove the screws. The very first thing you should do is remove the negative battery cable from the battery. This way you will not risk shorting out anything electrical as well as possibly triggering the airbag in the steering wheel column.
The key piece in starting the process is to remove the radio first and then central console panel that houses the radio. It pops out very easily by gently prying it out in the four corners. Once you get that piece out remove the screws the support the lower knee panel. In order to get that piece off you will have to remove the two screws the hold the hood release lever in place. Get under the dashboard and look up as you lay looking upward near the brake pedal. Pull the hood release lever and you will see the two gold screws. Remove them. This will free up the panel on the under side. The top side of the panel will pop out if you pry it gently on the top two corners.
Next, you will see a metal panel underneath the knee panel. Remove this metal panel as well. Now you will be able to remove the instrument cluster panel piece. There are some visible screws holding this in place, remove them and gently pry the cluster panel out. Once the cluster panel cover is out you will have to actually remove the gauge cluster itself by removing the the four screw bolts that secure it in place. After the screws are out, gently work it out of the dash slowly as you will need to disconnect three electric plug harnesses in the back.
After it is unplugged and out, on the backside of the instrument cluster you will see some round, black colored thumb screw bulb housings that house the light bulb. Just twist them and turn making sure to go in the right direction. Feel it out for the direction, I cannot remember which way it turns. The bulb housings are labeled "ILL" on the circuit overlay. I recommend you replace all the bulbs as you might not want to have to do this again in the near future. Once all the bulbs are tightly seated and installed just reverse the above process for installation. This is a fairly easy job and like I said it takes about an hour. Make sure you test the lights after finishing.
View 10 Replies
Not sure the problem is related.
The horn no longer works. The air bag light is on, on the dashboard.
I have checked all the fuses and they appear to be good.
How would I diagnose this problem?
View 7 Replies
I recently purchased a 1997 Ford Ranger with a blown 4.0 with a 5 speed , I have a 5.0 with a Carb and 5 speed out of a 80s mustang . Is it possible to use this in the 97 Ranger , I understand I need a different fuel pump but motor mount wise I was hoping it would fit.
View 2 Replies
Went to work one day and went to put my truck in park and it went as far as reverse. It has alot of play in the shifter. I have had a couple of people look at it and said that they would not touch it because of the air bag. I am not afraid to work on it myself if I just knew what to do. I am a single mom and on a budget, I would rather do it myself.
View 6 Replies
97 automatic 4x4 SXT 4.0L. 4Hi will engage, but when I shift to neutral, press foot on brake, and shift to 4lo, nothing happens. No light, no sound. Occasionally it will make a sound, and even more rarely will light up, but it does not feel like 4Lo is engaged even when indication says it is. I pulled the shift motor and replaced, as well as verified that the transfer case could be shifted to 4 hi and lo by using an adjustable wrench. I have not put truck on stands yet, but I'm pretty sure 4 hi is truly engaging. I did attempt to engage with shift motor connected electrically but not mechanically, and it shifted. What is keeping 4 Lo from shifting? If it's a vacuum issue, wouldn't 4 hi not shift? I did check the vacuum lines and the vacuum reservoir and they seemed to be okay.
View 3 Replies
I have a 1997 Ford Ranger with a 4.0L 2WD. The check engine light just turned on with a code of p0133. I know that this is something with the bank 1 sensor 1. I tried doing some research and I think that it is on the passenger side before the cat converter. Now, I don't know what to do from there. How do I go about fixing this? What part do I need? How do I fix it?
View 1 Replies
I have a '97 Ford Ranger with an automatic transmission that wouldn't shift out of park last night. A friend opened the hood and jiggled the steering column some, and finally it shifted. We checked the transmission fluid and it is full, a dark brown color. What the problem might be?
View 3 Replies
Besides being spark plugs and wires and/or a bad coil pack, what other things could make it so i have misfires on cylinders 4 and 6? going to replace the plugs and wires later today when they get to my house but i just want to know what other things i could be so I can evaluate the potential repair cost and should the wires for cylinders 4,5, and 6 be under or over the intake manifold? I bought my truck used and they are currently under the manifold i think it would make more sense to have them over personally.
I have a 1997 Ranger 4WD with the 6 cylinder 4.0L engine. I can't remember the codes that it tripped at the moment but i think one might have been the 304 code not sure though.
I tripped the 300,304, and 306 code but don't know about any others i remembered what codes i tripped the other day when i had it scanned
View 10 Replies
My son's 97 2WD Ranger with 2.3L, 5 speed, no a/c, basic XLT standard cab.
I was using his truck because my 93 Ranger was getting a new starter on it. I drove to work with no problems, then after work, it started just fine and drove a few hundred feet to a stop sign where it promptly died. I was able to start it again with some effort and drove to the next stop sign maybe a quarter mile away. Truck died again, but this time it would not start. Towed it home about seven miles and its in the driveway now. The previous owner had new Motorcraft platinum plugs and wires installed, new fuel filter, fuel injectors cleaned, all about 11,000 miles ago. My son has had it for about 6,000 of those miles.
It felt like it ran out of gas, but the gauge showed about 1/4 tank, and I put about 3 gallons more from a gas can into the tank with no change in being able to start it.
Here's what I've checked so far according to my Haynes manual:
Turned key and listened for fuel pump and it seems to go on just fine.
Checked fuses and they are fine.
Swapped around relays in distribution box with no change
Checked resistance at coil pack and it was about 1.7.
Checked resistance at one injector and it was about 1.7.
Checked inertia switch and it did not need a re-set.
I don't have the ability to check fuel pressure.
View 14 Replies
i have a 97 ranger xl with 2.3. it was recently crashed in the front, air bags deployed. i fixed the bodywork but couldn't get it to run properly. it starts but will not idle. i have replaced the iac , evr , maf. fuel pressure holds 35-40 psi running does not leak down after engine stops
View 9 Replies
I have a 97 ranger with 3.0 it runs great but once you drive it and shut it off and go to restart it it will turn over but not start it used to start once I let pressure off the fuel rail, but now is a little harder to start when it does this but it looks as thou coolant comes out of the reservoir when this happens I think it might be coolant sensor or thermostat problem causing the timing to advance until it cools but then again why was it starting when I released pressure from the fuel rail and also I don't believe my check engine light works...
View 8 Replies
My friend's 1997 4 cyl ranger died and won't start. Cranks fine with no codes on OBD2. Was running fine before it died.
View 5 Replies
I have a '97 Ranger 4.0 4x4 5 speed, as the title says... my radio does not work. It has an original cd radio and I had installed an aux cord. After I installed it I could only get a select amount of radio stations, last week I had went out of town so I didn't drive it at all, I came back and there was what seemed to be no power to the radio at all. No display, no sound. Only the lights on the radio controls (pre-sets, volume, seek, etc.) I have checked the fuses, pulled the radio and checked everything from behind and still nothing. Could the radio its self be bad? What else should I check?
View 1 Replies
I've been fighting some issues with the truck and decided to do a compression test to decide if I want to try to keep 'Old Yeller' alive or not. I'm all for working on it until I have to dig into the lower end of the motor. I rented a compression tool and the results were a little shocking. I did this test with a slightly warm motor, fuel pump relay pulled, all spark plugs pulled and throttle @ 100 %. Motor turned over 10 times for each cylinder. I even moved all the rubber o-rings on the tool up on the threads to make sure I was getting a good seal.
Cyl 1 - 40
Cyl 2 - 0
Cyl 3 - 0
Cyl 4 - 80
Cyl 5 - 0
Cyl 6 - 60
Needless to say I didn't even bother doing this wet. My only real question is can this be close to accurate. I drive the truck daily. 160k mi on it.
I'm fighting the dreadful P0171 and P0174 codes and after a couple cycles I will get misfire codes. Its low on power (hard to keep @ 70MPH with some wind) and gets 10MPG right now. However it starts and runs and stays consistent (even though it rumbles like it has a nice cam in it).
Is it time to put Old Yeller down ? Are these compression results even remotely accurate ?
View 5 Replies
1997 2.3 Ranger w/ 160,000 mi. Every few months it won't start, sometimes after just having been running fine. Symptoms:
-the dash lights will be dim or off completely
-the chime will be softer than normal
-the headlights will not work, or be dim
-the starter will sometimes briefly click, sometimes crank once, sometimes do nothing
-the emergency flashers will sometimes click much faster than normal
-if during one of these "episodes" it does start, the battery light will sometimes flutter on and off, and the meter will flutter a little higher than normal. The next time I stop it, it typically will have the same problem.
-it will typically start if i get it jumped
My battery, starter, plugs and wires are all fairly new. On occasion, when it is having this problem, and I am trying like crazy to start it, if when I turn the headlights on and they are no longer dim, it starts right up and runs fine.
View 7 Replies
997 2.3 TruckSo this has been an issue for a long time, actually one of the issues I had when I got the truck 3 years ago. After it rains or is extremely humid, my truck does not want to start. Sometimes it will after cranking and cranking and cranking for a while (stopping to cool the starter of course) and other times it won't start.
This time around, it won't start. I cranked it for a little bit and had my dad check for spark while cranking. No spark at all. What should I start looking at? Coils, crank sensor and wires are all newer. As mentioned before, EEC has been replaced. Could it just be bad luck and I got a crap crank sensor? All fuses and grounds are good.
No codes, either except for the occasional misfire code that I get for some reason after pushing in the clutch to decelerate from a higher RPM. It'll fall and start to misfire, but clear up when taking back off.
View 1 Replies
