Ford Ranger / B-Series :: 1998 3.0L V6 - Injector Rail Leak
Oct 20, 2012
I bought a '98. At the front passenger side of the engine, the injector rail is leaking fuel (a fair stream of it). I have done some googling, and browsing around the forums, and can't find much in the way of specific info on where to start with this.
Whatever the device at the front of the rail - Without digging too far, it seems that the leak is coming just below it.
Questions:
Am I obliged to change injectors with the rail?
What is involved with changing the rail? Removing upper intake only? At all?
What is the box shaped device at the front of the rail, passenger side? Test port? Pressure Regulator? Both?
I won't have a chance to work on this again until next weekend, but thought I'd try to do some homework beforehand.
View 10 Replies
Advertisement
I just had trans rebuilt in my 98 4x4 4.0 ranger I thought while they had the trans out go ahead and replace rear seal. Got the truck back leaking bad carried it back they claim to have replaced it twice while they had it and guaranteed it was not leaking they say the leak is from the oil pan so I'm gonna pull the motor this week. Question is: can make an offset rear seal I still believe this is the problem. Which oil pan gasket to use.
View 4 Replies
I have a 98 Ranger 3.0 with a standard transmission. The truck has 240,500 miles so far. It runs just as good as the day I got it 11 years ago, doesn't use any oil and still gets 23 MPG. Last fall, it developed what sounds like an exhaust leak under the hood. It seems to be coming from the area of the EGR valve. The trouble is that I can't feel it or smell it. I have carefully felt the entire length of the tube running from the EGR to the exhaust manifold and cannot feel any leaks. There is no soot or any other evidence of an exhaust leak.
The noise isn't there for the first minute or so that the truck is running. I would think that if I had a cracked manifold or some other such leak, it would be worse when the engine is cold but this is not the case for me. It is most noticeable when pulling a hill as slow speeds in a higher gear. I have checked for codes (no CEL) and there are none. When I first heard it I figured that I would wait until it gets a little worse and I would be able to find it. Its been been over 8 months now it has remained the same.
View 1 Replies
My ranger decided to start leaking fuel somewhere probably a few weeks ago. I can smell it whenever I start the motor, and sometimes while driving with the windows down. Last night, I finally looked into the problem. I took the intake air hose off. The hose, air filter, and whole intake smells like gas. I'm thinking that shouldn't be the case on a fuel injected engine. After seeing some people talk about the Fuel Pressure Regulator go bad, I pulled the vacuum line off of it, and it has a very strong gas smell. I don't see any gas coming out of it, though, even with the motor running. Everything I read says if the regulator is bad, then gas should come out of the vacuum line. Is there another check I can do on it to confirm this is the problem? Is there somewhere else I should be looking? It got two new heads right before this problem started, so its quite possible I knocked something putting it back together.
View 6 Replies
There are 4 holes in the top of the bed for rails, what size board fits in, and how would they be mounted/ attached?
View 7 Replies
I have a 86 ranger 2.9 5 speed. A few days a go I replaced the front fuel filter and all seemed ok. Last night on my way home the truck quit and I had to have it towed home. Now I find both pumps don't seem to be working. What would make me loose both pumps??
View 11 Replies
I have a 2005 ford ranger, 4.0 auto, 4x4, 60psi fuel presser, has spark and injector pulse, will try to start if you hold the throttle a little over 3/4 the way down, but will not fire on starting fluid.
View 3 Replies
I think a fuel injector is stuck open on my 97 Ranger 3.0. How can I check to see if I'm right and which one it is? I've heard about the "listening to the injectors" trick but I'm not sure what procedures to go through. Can I tell if one is open by taking them out and visual inspecting?
View 9 Replies
Its a 2000 flex fuel 3.0... Its not the actual injector. I think its wiring or computer. No change in idle when I pull the injector plug. But I think I can feel the injector opening and closing. Compared to nearby injector diagnostic light flashes less brightly. but that's pretty hard to quantify
When I pull the plug on another injector it idles about the same but I can tell it surge up and down as I disconnect and reconnect it. Fuel injectors were backflushed and swapped same problem cylinder. Where do I go from here just take apart the loom and look for abraded wires? Its the number one cylinder, passenger front.
View 2 Replies
I thought id tackle installing my new boss intake this morning and didn't think to clean everything up enough and after i removed the fuel rail some dirt and small stones one was about a quarter of in inch round fell into the injector hole. I no that all will be in the engine now and I feel awful about it.
View 14 Replies
My sons 1998 ranger is in mph. Converting on to a kmh dash. There's one at the wreckers and I was wondering is it a direct replacement or is it a computer swap also? What years would work?
View 5 Replies
I have a 1998 ford ranger and it will not disengage out of 3 gear. The truck still starts but if you let of the cutch. Of course, It stalls. I'm doing the work myself but where I should start looking.
View 1 Replies
I have a 98 4x4 with 145k miles and 4.0 OHV. Symptoms are as follows;
Uses ALOT of oil. 1 quart per 230 miles. Burning bad in rear cylinders, some in middle cylinders, none in front cylinders. Screams intake or PCV issues to me, not rings or valves. Never any smoke, not even on startup. No significant leaks. MPG always 18-20mpg.
Slightly rough idle.
Miss under load below 2k rpm. Not a terrible miss, but you can feel it. Has never lit the CEL. I know the CEL is good.
Never loses coolant. No coolant in oil or vice versa. Haven't done compression test, but doesn't seem like they ever tell you much anyway.
This weekend I replaced all intake gaskets, plug wires, cleaned oil residue off and regapped plugs (they are 3 months old), injector orings, and PCV valve. Flushed and burped radiator.
It's too soon to tell on the oil consumption, but I thought the intake gaskets would have cured the rough idle and misfire. The idle IS much better, but still not perfect. But the low rpm load miss is actually worse now. Still no CEL. Could it be storing codes without lighting the CEL? Also, how do you clear codes on these, can you just disconnect battery, or do you have to clear them with a scanner?
View 14 Replies
I have been having with my ford ranger. I bought this off my nephew bcuz he needed some money and never drove it due to it being a 5speed and he has a kid and a wife and no room. OK the issue I am having is in gear or neutral I can't get the 2.5 motor over 3000rpms in any gear at all. If you rev the engine up or r driving it when it hits between 2900-3000 rpms the motor acts as if it is going to die and looses all power until you let off the gas. I have replaced the following items on the truck. Oh by the way I have a Cam 2 hand held and there are no codes or warning lights. All new parts :
1) new fuel pump
2) fuel filter
3)new timing belt
4)new motor craft platinum plugs
5) new motor craft plug wires
6)new Mass air flow meter
7) clutch,pressure plate & throw out bearing along with new slave(that needed it replaced others since I was there)
8) exhaust tube behind motor(rotted out)
9) new idle control sensor (acts as elect. Choke)
Truck starts up real quick and idles fine, but when truck is cold the rpms @ 2500 does the same as when it is warm @ 3000 rpms. I even took it to the local ford dealer in my town. Youngstown oh @ Fred martin ford. They told me the wires should be replaced and plugs along with mass air flow valve. I called them after replacing it and told them no difference and the service manager told me to bring it in again and they will look again. Service manager told me he has never heard of this type of problem and I went to a local garage mentioned it to the lead mechanic. He said that is why he doesn't like fords they are to common in chronic problems and can't be fix without a lot of guess work. I have a Hanes manual and did everything it recommends to no avail.
View 14 Replies
I've got 30 lbs of fuel pressure that drops to 28 if you rev it up a bit on a 1998 ranger 4.0 with a new fuel filter. Haynes manual say it should be 56-72 lbs. Bad news is fuel pressure regulator is in the tanks with the pump. Can the regulator be swapped out or is it one assembly with the fuel pump? Is there anything I should check first?
View 4 Replies
Ok so my dad has been using my 98 while I was fixing his 92 4.0. I had the 92 perfect and then someone pulled in front of me and totaled it out. Well now I got my 98 back and it's all messed up. Check engine is on p0171. Fuel pressure test done and it's steady 40-42 psi. I remember last year I checked it was like 68-72 psi. It hasn't been a year or two since fuel pump and strainer were replaced. Filter probably 15,000 miles ago. It's currently running good sometimes it cuts off when you start it then next time it stays running. Is this another fuel pump failure? How much longer will it last on 40 psi? The fuel lines and tank have 336,000 miles, engine maybe 150,000 and injectors have about 20,000 miles on them.
View 4 Replies
I got this 98 Ranger 2.5 that I've done a tune-up on less than 30,000 miles ago. I changed plugs, wires, and both coil packs. Timing belt, thermostat, fuel pump, fuel injectors are all recently changed too within a year or two. Fuel filter and air filter I change every 30,000 miles. The truck runs as great as a 4 Cylinder will run. It's at 344,000 miles but the engine was changed once so it probably has over 100,000 miles on it. There is just a slight miss you can hear through the tailpipe but it's not severe enough to be picked up by the Check Engine Light. In fact, even when the coils were totally gone it never put up the Check Engine Light. I can tell when a coil pack is going out on this because it's done it several times so I usually just change them with the tune-up. It's only a slight miss some people may not even notice it. I was just wondering is there any way to track down where the miss is? I tried looking under the hood in the pitch black and there's no plug arcing.
View 1 Replies
so heres whats happening. My 98 ranger speedometer has not been working since I owned it (I am the second owner who got it from a grandpa) and I've replaced the vss sensor two times, got a new connector and gave that a try and still nothing. Yes I've looked for cracks in the wire or any exposed copper, I've looked through many forums and cant figure it out. At first before replacing the vss, my abs and check engine light weren't lit up until i put a new vss sensor on that i got from o'reillys, so then i got another one thinking it was just a bad sensor and still no luck. another thing is when its cold in the morning and i get in my pickup to go to work it will start working once i go over 30 and fluctuate between that and 20 but if i don't accelerate it will not bounce all over the place.
View 4 Replies
I have a 98 Ranger SuperCab XLT 4WD 4.0 Auto. Occasionally, especially when it has been sitting for more than 3 days, it shakes for maybe 30 seconds on startup. It smooths out gradually after that, maybe 15 sec. to normal smoothness. It seems like it is firing on all cylinders and is more like something out of balance.
Never does it when sits less than 2 days. When it happens, the longer it sits the worse it shakes.
View 3 Replies
Throwing codes ... p0136, p1131, p1151 acts like it going to just stop then will take off, at a stop light it will sound like it has a large cam in it... It is a 1998 4.0 V6 automatic tranny.
View 1 Replies
I understand there is not much adjustable on my 98 Ranger (2.5L) as far as idle speed and mixture. It runs rough when started cold. Is this a sign to replace spark plugs?
View 2 Replies
