Ford Ranger / B-Series :: 1998 - Randomly Feels Like Hit Rumble Strips
Dec 28, 2016
I have a '98 Ranger 4.0L SuperCab 4x4 Automatic
The other day i was driving, around 40 MPH and suddenly the truck felt like I hit rumble strips on the highway, I hit the brakes and when the truck got down to about 10-15 MPH, it went away. It didn't feel like an out of balance tire or anything like that. It felt exactly like I hit rumble strips. It was a strong, high frequency vibration. I then continued on my way, and it was fine for a little while, still doing 40 mph, then suddenly out of nowhere the same vibration came back. Once again, I slowed back down, it went away and stayed gone even when I sped back up.
Both front hub bearings are less than a year old, and a quick check of the driveshaft seemed to indicate the u-joints are still tight. Front diff/driveshaft turns freely and smoothly and the front hubs are not locked.
'm going to try and jack the truck up and check everything thoroughly, but I'm really at a loss here, as I've never experienced anything like this before in any vehicle. Some reading suggests that it might be transmission related to the 5R55, but I'm really unsure.
View 11 Replies
Advertisement
I have a 2000 f150 lariat. Mo problem started about 2 weeks ago. Around town its fine but when I go over 50 mph it feels like I'm driving down the rumble strips on the highway and after a couple miles it just smooths out and its fine! Yesterday I went on the interstate and it did the same but this time I ran up to 85 and the vibration stopped.
I had another motor put in about 2 months ago, #4, and he changed my rear u joint as well. I replaced the rear passenger side wheel bearing a couple months ago but there seemed like a little play in the axle still but not bad. I've been to the dealer and a few other mechanics but it doesn't do it all the time and they couldn't find what is wrong.
View 6 Replies
I have a 02 durango. Yesterday once i was accelerating over 30 it started feeling like i was driving over rumble strips a little. It felt like it was towards the back. I drove 15 miles to the store and back. On the way home it died down and went away. Today I started driving to town and it is doing it at all speeds. The vibration doesn't seem to change with speed but is much more intense. Only happens when I give it gas. I have searched many forums and not sure where to start? I've read everything from torque converter to solonoids to u-joints, axle bearings, engine problems, or a bad differential.
View 5 Replies
Ok I've got this 98 Ranger with the 2.5L and the 4r44e automatic. The engine is used and has about 100,000 miles now and is it a good state of tune - so I think. The transmission was a remanufactured I bought a few years ago that was built with the shift improver kit, Kevlar bands, extra planetaries, 4wd pan, and external cooler. It's now got 92,000 miles on it and it's been serviced every 30,000 with a fresh 4wd filter and Mercon V fluid. It's outlasted the last 3 transmission I've had in my Ranger. I've got 315,000 miles on the body. For awhile it was randomly losing power while driving like it wouldn't shift, almost like it dropped a couple cylinders, then as you kept your foot on the gas it would recover and rev up and shift.
Then sometimes randomly at stoplights it would shake at a stop and have no power at take off until it hits 30-40 mph. Sounds like a converter, is what I thought. But now it's doing it more often but not the shaking at stoplights as much as randomly losing power while driving normal speeds. Last night I drove it about 50 miles after doing a fresh filter and fluid change and this time it did it so much it threw a code up P1131. Even though that's a O2 sensor code, could it be hidden by a transmission valve body problem? One transmission shop said it could be a valve hanging up just by me describing it to him. Could this be ignition or fuel related or is it all tied in with the transmission problem, if it is even a transmission problem?
View 3 Replies
Problem: Vibration together with a noise that sounds abrasive and destructive. Mechanics have failed me.
It feels like driving over the intense short rumble strips that are meant to tell you when a wheel is outside the traffic lane. I feel and hear it in any gear, whether I am moving or not, but hardly at all in Park or Neutral, and hardly at all when cruising at high speeds. It is worst on the first drive of the day - much less on subsequent drives, even if the engine has been allowed to cool fully.
History: When this began, less than 600 miles ago, I had the transmission checked, where I had warranty coverage.
Found: No transmission trouble but a broken engine mount.
I had the engine mount replaced (and two gaskets replaced because they had started to leak), together with Virginia's mandated annual inspection - passed.
Vibration lessened but continued and started to worsen. Within 3 days the engine stalled in traffic and THE NEXT DAY the "check engine" light came on. I went back to the same place. The ignition coil and spark plugs were replaced. Power returned, and no stalling or warning light, but the vibration persisted.
One mechanic baffled: "What do you expect with 101K mileage and 16 valves?" - But this came up too fast to be ordinary wear and tear. What should I do?
2.0L Zetec E engine.
View 9 Replies
My 2010 F150 randomly feels like I'm driving over the rumble strips as well as a small jerk like there is a cylinder misfire. If keep it at constant speed it still happens, but under cruise control it stops. Even when load increases like going up a hill.
View 14 Replies
I hooked up the boat and went out for a tow. I ended up getting a pretty good vibration and thought maybe it was time for balancing the trailer tires. As it turns out I needed two new tires as they were at the wear bars (cheap crappy bias ply tires) so I ended up buying 4 trailer tire radials and had them balanced.
As it turns out I have what I guess is a shudder at slow speeds and also can feel it at other speeds as well. A way to explain it is that it sort of feels like you are driving over the rumble strips on the side of the road but really small ones.
View 14 Replies
Had the torque converter replaced twice on my 2007 Explorer Limited last December. Ford dealer did it once and then there were still issues so they had to replace it again. All seemed fishy to me.
Now a new issue that sounds like driving over rumble strips. Torque converter?
View 1 Replies
Very weird thing happened on the way home from work. When I left work (not to full temp) at about 1500 rpm and 30 mph (had to be at 30mph--seemed to be the key) the whole truck felt like it was rolling across rumple strips (the ones one the shoulder of the road) all vitals were normal and it was gone once on the interstate and up to temp (I did gon on it to blow out anything that may have needed to be) it felt more like drive line but honestly can't say. 2006 F350 4X4 ....
View 7 Replies
I've looked at all the shudder issues thru the forums and mine seems a little different. Mine feels like I'm riding over tiny rumble strips or like pebbles and at all speeds. I just got new tires and a front end alignment. mine seems to do a little bit of that shudder thing but all the time. I bought it used from a honda dealer with 48k on it. I have to take it to them for the warranty they gave me. Curious how that's going to work out. 2009 5.4 3.55 rear and 157" wb. 4x4.
View 3 Replies
I'm having a bit of an issue with my 97 ranger 4.0 auto 2wd. I have an vibration which from a stop up about 10 mph feels like wheel hop not bad but you can definitely feel it it and over 50 mph the whole truck starts to shake again not bad but you know its there. the truck sat last summer it was my dd till a bought a new car and now vw is buying it back ill be driving the ranger in the mean time. I have been trying figure it out for a few months but no luck i have put new tires , front rotors and rear drums , drive shaft support bearing ( 2 pc shaft) new u-joints and a used boneyard shaft with new u-joints as well, checked the tail shaft bushing which had about .008" of play.
Pulled the drums Off today and checked the axle bearing for play only .004" of play pulled the diff cover and checked for carrier play as well as pinion play but can't find anything. I'm at a loss here and looking for other things to check ... Don't know if its possible that something in the transmission is loose it was rebuilt about 75k miles ago I was going to stop and talk to the trans shop to see what he thought (its a 5r55e ) ....
View 14 Replies
I have a 2010 Ford ranger sport 4x4, manual, and when backing up at a decent speed, then press the brake to slow up then depress the clutch, the brake pedal pulsates and it feels like something is grinding. It has happened in first once, but I can make it happen in reverse anytime...
View 1 Replies
My truck just recently started to vibrate like it is going over rumble strips. It only happens over 40MPH and sporadically. It seems to happen when I'm just giving enough gas to maintain speed. Once it starts if I let off the gas or give it more gas it goes away. It reoccurs anywhere from 20 seconds up to a few minutes. I'm afraid my tire is going to fly off or my drive shaft is going to drop. There is no unusual noises or thuds if I go on and off the gas and the universal joints seem tight, and there is no vibrations from on steering wheel.
View 10 Replies
2001 Dodge Stratus R/T, 5 speed manual - under load, it feels like I'm driving over warning strips in the road, and stops when I coast. The CVJ's feel and look OK. So do the wheel bearings. Could it be something in the final drive? It happens in all the gears.
View 1 Replies
I have a 09 Subaru Forester with 66k miles that vibrates like it is going over rumble strips when it up shifts from 3rd to 4th gear. It occurs under normal (not brisk) acceleration. I had the trans fluid changed at both the 30k and 60k services. I have owned this since new. It began before the 60k service. Also, sometimes the tach will increase revs during this as well. I don't know if this next thing is related but when I once need to merge quickly into interstate traffic I gave it a good amount of throttle and the tach revs increased but the trans did not follow with an immediate down shift.
View 4 Replies
My 2005 Infiniti G35 has 144,000 miles, two new rear tires and two good front tires. Sometimes, and I cannot nail down or reproduce-on-demand this situation, my car will suddenly begin to vibrate as if I'm driving over a smaller version of those rumble strips on the side of the road. The vibration continues when I take my foot off the accelerator, and will continue at a slower rate as I decelerate until I stop. Often it seems that when I come to a dead stop and accelerate again, the vibration stops, but other times it will continue as I accelerate.
But what's really odd is other times I'll just be cruising along and the vibration will begin, keep vibrating for a few miles, then peter out and disappear. I haven't totally nailed down whether or not braking affects it, but if pressed I would say that I would use the brakes at least once before it disappears. Also, it only seems to begin once I hit 50-60 mph, but again, it doesn't happen every time I go this speed. Other times this car drives incredible and makes the road feel as smooth as glass.
I haven't taken it to the shop because I'm sure they won't be able to reproduce it.
View 11 Replies
I got a 1997 Ford Ranger 2.5L that randomly jerks on the highway and I can't figure out what the problem is. This morning I had a 3 hour drive and it was fine on the first hour and then the last 2 hours it will randomly jerk on the highway and then be find for a little bit and then do it again. I don't know what the issue is? I did scan my car this morning and did have two code P0141 and P0113 not sure if these would have anything to do with it or not. Also my speedometer is hit or miss when it works, other than that everything else is fine on the car no check engine light or anything like that.
View 6 Replies
In my 08 Ranger, when I'm filling up with gas, and I flip the lever on the handle of the pump so that it stays on, and then gently let the nozzle rest, in all my older cars it would stay on until the tank was full, and then just click off. But in the Ranger, it clicks off randomly, with nothing to do with the amount in the tank. I'm pretty sure it has something to do with the angle of the nozzle, because when I hold the nozzle lightly from where the hose enters the nozzle, so that the spigot it at a different angle, it doesn't click off.
Is this a design flaw? (because it's not like any other car out there in that respect) and can I do anything about it?
View 2 Replies
Ive got a '94 ranger with the 8 plugs and more often than not while driving and sometimes when it first starts, the cel comes on and immediately I notice a lil rough running and lack of power. Also my milage has dropped since this has started. Plugs, wires, o2 sensors, not to familiar with my gas saver. I love it cause I can just get in it and go. With twice the fuel milage as my bi truck!
View 14 Replies
I have just inherited my recently deceased father's 1992 Ranger with the 2.3 liter engine. He was a Ford Mechanic but got to ill to worry about fixing the Ranger. So, let me begin, the engine dies randomly, (at idle or in gear driving doesn't matter what gear or speed), turning key to off and then to on will allow vehicle to restart every time. No "Check Engine" light has ever lit, I do have an "Antilock" light that comes and goes. The engine codes I keep getting are: 10, 218 and 222.
Code 10 is a computer check code,
Code 218 is "Loss of Ignition Diagnostic Monitor (IDM) signal/left side, and
Code 222 is "Distributorless Ignition System - Loss of right side ignition diagnostic monitor (IDM) signal.
These codes were from my Innova reader. I have read where other similar problems were fixed with a new Crankshaft Position Sensor, replaced mine, no change. Another symptom I just noticed is my temp gauge stays near the cool end when it should be higher.
View 14 Replies
2003 Ranger (4.0 L-2wd)...
Codes - random misfire and cylinder banks 1, 2, 3, reads out lean fuel
Will be checking out injectors and rail pressure, however, trouble shooting in general for this issue.
View 7 Replies
