Ford Ranger / B-Series :: 1999 - Smoke From Steering Column
Mar 15, 2013
Within the last couple of weeks, periodically I see small amount of smoke coming from the steering column, from the hazard switch. It only lasts a couple of seconds. I've owned my 99 Ranger for about 7 years now, and since I got it, the dome light has never worked, even when installing new fuses. I'm suspicious it's the multi-function switch but not sure. What this means. I'm no mechanic, I just read alot, and from what I've read, this seems to be the issue.
View 3 Replies
Advertisement
Can't seem to figure out what is making this clicking noise. It comes from under the dash, drivers side, under the steering column... Now as for when this happens, anytime! Truck on, idling, driving, truck off, key turned to acc or key to on. Also happens even when key is not in ignition?! What this could be? Brand new battery and connecting rings/wires.
Additional info: 1996, 2.3L about 150k miles on her and she's still going strong
View 2 Replies
I've been having problems with my column shifter ever since I installed a Pioneer shift cable probably about 3 years now. I was told and also thought that the cable would loosen up after awhile but it never has. I had some put it on and I watched him do it. He seemed to have some trouble because it took him a long time under the dash. It shifts so stiff that over a period of about 2 years it finally broke the end of the shift tube one night. Luckily I was able to fix it the next day by getting a spare without missing any down time. It was still just as stiff with the other shift tube. It finally broke the plastic on my shifter tonight, not necessarily whatever is causing it but because it takes so much effort to shift into Park, Reverse or Drive.
I think the plastic may have cracked over time. Luckily I had another one at home along with another shift tube. I didn't replace the shift tube this time but I did remove the caps and smear some grease on the bushings to see if it would make it turn. I looked further down at the end cap that broke last time and sure enough one of the bolts was backed almost all the way out. I retightened it tonight too. That's what happened when the bottom broke last time. One of those bolts backed out and it cracked the housing. It works now but if you go all the way to 1st to get back to anywhere it really takes a tremendous amount of effort to get it to shift. Something is not right and I cannot pinpoint it. I know they offer brand new shift tubes but I'm not sure if that's the problem.
View 2 Replies
So yesterday I was on my way home from work, and I had smelled a little burning and then I saw smoke from the steering column???? i pulled over and it had stopped no lights came up? the car is fine now..? I don't know whats going on?
View 4 Replies
I had suddenly developed a case of P/S high frequency SHUDDER, on my 99 Ranger, when the steering wheel was moved to either side of center. The fluid level & condition were A ok!!!!, I have kept it changed, so it's never gotten dirty. I removed about 4 oz of fluid from the P/S pump reservoir & added a like ammount of SeaFoam Trans Tune, to bring the level back up to full. In about 10 min 90% of the shudder was gone, After a 40 mile fishing trip to the lake, 99% was gone. The next day, after another 40 mile drive to the lake, fishing, it's ALL gone. So if your experiencing P/S shudder, try a SeaFoam Tans Tune treatment & a fishing trip or two, maybe it'll tune both of you up, did ME!!!! LOL BTW this is the second time the Trans Tune has worked on a P/S sticking/shudder problem, worked on my 94 Taurus two years ago, when I was experiencing a "sticking" problem with the steering wheel turned WELL off center & it's still ok. So if your having that kind of P/S problem, don't be afraid to try the Trans Tune, & a fluid flush & change, if it's dirty, like the Taurus fluid was, it just might WAKE things up.
View 11 Replies
I picked up a 2001 ford ranger with a 2.3 from a friend of mine for next to nothing. it has a serious oil consumption problem. he just put a head gasket in trying to fix the problem with no luck. he thinks it has a broken oil ring. the truck only has 99xxx miles on it and i find it hard to believe that it broke a ring. I am thinking it has to be something like a bad pcv. If it is rings ill do the job but I don't want to pull the motor down just to find that all the rings are good and it was something that i looked over
View 11 Replies
My wife got off work tonight and went to start up our 2001 Ranger XLT, it starts, but wont stay running unless she puts the gas pedal down, it is also blowing white smoke from the exhaust and she says it sounds like it is missing, sputters and dies when she takes foot of gas.
No previous symptoms, ran perfect this morning, no loss of power all day, no smoke no sputtering and no check engine light. Any clue as to what it is. I have heard head gasket and O2 sensor.
View 3 Replies
Finding the fix for the rich fuel puffing black smoke fuel reg ok, map ok, temp sensor ok, air sensor ok...
View 14 Replies
1988 4.0 - noticed fuel mileage going down and an occasional stumble for a while but now I am getting some black smoke more when I let off the throttle than when I going down the road if I rev the truck get all kind of black soot all over the floor otherwise runs fine idles fine the iac has been replaced air filter replaced check the fuel pressure regulator for any gas leaking into the vacuum line and its clean.
View 14 Replies
I have a 97 Ford Ranger / 2.3L / 4 cylinder (L4) / 5 speed manual / XL Supercab / 140k miles. I had been having some Check Engine issues and ran rough in town stop light to stop light. But was fine on the highway.
On several visits to the parts store, their OBD tester showed:
PO303 (Cyl 3 misfire detected)
PO141 Bank 1 Sensor 2 O2 Sensor (heater circuit malfunction)
PO171 Bank 1 Combustion Too Lean (the most recent new code to show up)
And the following would show up sometimes, but other times not:
PO 402 EGR Flow - Excessive Detected
P1409 EVR (I cant remember the exact error message for this)
Regards the PO141 code, O'Reilly's sold me a Bosch O2 Sensor (Bosch 15719) and the sales rep told me it was the sensor closer to the engine. And with the attached cable length on the sensor showed was indeed the sensor closest to the engine. But I've been advised the Sensor 2 is for the 'downstream' sensor, furthest away from the engine. And the other sensor, that I replaced is the upstream sensor. And the error continued.
Then back issues showed up and I had back surgery this past year and thus drove the vehicle sparingly. Never resolving the check engine issues. (My bad). Ran on the highway ran fairly well. But recently noticed longer acceleration times and unable to top 65 in 5th gear. I bought spark plugs and plug wires and had plans to change next week.
Yesterday as driving down the Interstate, was 90 miles into my trip, I noticed loss of power even in fourth gear. (note it was the hottest day of the year at 100F). It seemed I used more gas than usual for that distance. I stopped for gas on the Interstate and power seemed to improve. Then about 130 miles into my trip I hit some heavy stop and go traffic, and wasn't able to keep an idle and the engine died numerous times if/when I didn't give it gas at a dead stop. The heavy stop and go heavy traffic and the issues persisted for a half hour for more than five miles. Then when traffic opened up the truck seemed to have a bit more power in 4th gear again. And up to that time all my dash gauges were showing fine. Then a couple miles or so down the interstate, driving 65mph in the inside lane, the check engine light started flashing quickly. And at the same time a sudden loss of power, rough sounding engine with heavy white smoke coming under the hood. And looked back in rear view mirror, with nothing but heavy white smoke. Managed to cross three lanes in heavy traffic and was able the vehicle to the outside emergency lane, finally coming to a stop.
Looked under the hood and saw oil dripping everywhere but with all the oil everywhere I could not find a prime source. Looked like the oil came from the top end of the engine and dripped down. Measured the oil at the dipstick and it seemed like I was at least a quart plus down (I checked the oil before I left on the trip). And it didn't look like any water was in the oil. And my radiator overflow tank was at the proper level. So I figured I lost all that oil during that period of "white smoke".
So had my vehicle towed home. Today in daylight, I did some more inspection and removed the air intake system (hoses and canister) from the air filter to the throttle body. There was significant oil up to the canister piece that fits on the air filter canister (but no oil in the actual air filter), and significant oil inside all the hoses up to inside the throttle body (up to the butterfly which I could see),
When I disconnected these hoses I noticed the blow-by hose connected to the intake hose system was not connected to anything. And a tube opening on the valve cover was open without the a blow-by hose attached and, with no clamp. So I assume all that oil and came out of that blow-by tube on the valve cover, (white smoke created by hot oil hitting the engine).
So appears to me that its not a blown head gasket or worse, which I first feared.
I have the vehicle parked at home.
QUESTIONS: So what are the suggested steps to troubleshoot and repair? Besides reattaching everything and putting a clamp on the blow by hose? And installing new spark plugs and plug wires. I previously replaced plug wires around 60k, even though the manual recommended 100k mile replacement. (And a couple yeas back I had the dealer replace the PCV, which was recommended in the manual and included in the warranty. The timing of the initial check engine lights appeared shortly thereafter).
Is there suppose to be a large amount of oil in the air intake system after an incident like this and should I try to clean/flush out the hoses and the inline canister?
When I disconnected the inline canister from the hoses in the air intake system, unfortunately I failed to document the direction which the canister goes. It has outside markings "ADP with a forward arrow with some horizontal lines, and then at the other end upside down markings with a greater sign PP less than sign. Should the forward arrow point toward the throttle body or toward the air filter (I'm thinking in the direction of air flow, toward the throttle body). I've taken some photos of the engine with air intake hose system unattached, if that might work...
View 2 Replies
I have a 1994 Ford Ranger with 4.0 V6 Automatic. The problem is when it idles it idles low and surges up/down and pushes a very small amount of black smoke puffs and smells like gas. I have installed new coil, new wires, new plugs, new ect, new crankshaft position sensor, and new maf. It has new intake manifold, new injectors, new alternator and it still does the exact same thing. Nothing is phasing it. I ran the key on/engine off test and got egr codes and a map sensor code, then ran the engine running test and got 998 and 126 code. The 998 code says that its basically a hard fault/ have no idea.
I do know this is a donor engine out of another year not sure what year, but i know when i ordered the coolant temp sensor the only ones that would plug into it are the years 1990-1993. Now here's my other question, why would the computer give me a map sensor code when truck doesn't have a map sensor? It has MAF sensor, and why egr codes? The truck doesn't have egr and never came with it. I do know I've unhooked battery and replaced the maf and its like it doesn't even recognize it? Could it be the ecm/computer bad or needs flashed?
View 5 Replies
My brand new 2016 F-250 Super Duty has a misalignment running down the steering column. Looking just over the top of the airbag cover, the shroud that protects the gear shift and upper steering components is depressed on one side... and further back, the shroud for the cluster is depressed a different direction. Certainly nothing earth shattering, but it annoys me every time I see it.
View 2 Replies
Well I finally went and bought another Ranger. Pretty red 5spd 4WD long bed. I knew it didn't run when I got it (crazy leaky fuel line...stupid squirrels), and the owner was pretty sure it had a head gasket failure. He claimed it was blowing white smoke and using coolant. I hadn't been able to get it to run to verify that, but I can't see why he would lie about that.
I finally got the fuel line fixed today (FYI, don't waste your time or money buying those Dorman OEM connector patch kits at Advanced Auto). While we were cranking the truck, I noticed gas escaping the degas bottle the radiator was pressurized before the thermostat should be open. That to me says blown head gasket (crossing fingers it isn't a cracked head) for sure. I tried to get a picture of the dipstick, but in the light it definitely looks like peanut butter. I just wanted to make sure before the massive ordeal of pulling heads/top end work that will follow
Anyway, plan is to fix her up and get her back on the road! Some picture enjoyment .......
View 14 Replies
I have a 1997 Mazda b4000 new plugs wires head gasket an I cleaned out the radiator. My question is the truck runs good but my heat quit workin what could it be all fuse look good. Also there is water coming out of my tailpipe with white smoke. Should I be concerned.
View 2 Replies
My steering wheel is loose as in moves back and forth if pushed or pulled right at the wheel.. everything else seems tight and still turns and drives fine.. took off the airbag and the center nut is tight.. it's been getting progressively worse since I bought it.. What it could be??? Loose bolt or nut or the steering column?
View 2 Replies
I have a 2002 F250 diesel, the key will turn to acc. but not on. It feels like it is hitting something in the column. I tried moving the shifting lever back and forth with my foot on the break, as I turned the key but it would not turn. I am thinking the tumblers are OK because it goes into acc. It feels like their is some lever that is not releasing the shift lever, because if I turn the key hard the shift lever jumps. What is wrong, or how the interface between the lock tumbler and the shift lever works?
View 4 Replies
I have a 87 ranger with a 2.9 and recently it started to act up when i start after its been sitting for a couple hours it has a rough rolling idle and will stall out and a lot of white smoke out the tail pipe and some times a tiny bit of black smoke when revved high....after a about 10 mins of feathering the gas it will even out and runs no problem.... oh and quite a bit of moister comes the tail pipe....and this issue just occurred over night every time before never had an issue like this...
View 5 Replies
2002 Ford Ranger edge 3.0 flex ... Truck was running fine and giving me no issues. I woke for work the other day and went to get coffee and truck wouldnt start. I could hear fuel pump running and knew it wasnt that, it was acting flooded. So today I pulled fuse from fuel pump relay, and got it to start. Put the fuse back in and ran to gas station. On the way to the gas station it started running really rough, very low and rough idle, trying to stall out. I noticed it had black smoke coming from exhaust. I got it home, and got it to start barely, and it has the same very low and rough idle, but my oil gauge was going crazy, flickering back and forth all crazy, and the idol is terribly rough and eventually stalls out. Earlier today I did put new spark plugs in it, but not sure that has anything to do with the issue. I also hooked it up to a computer and it isnt throwing any codes.
View 13 Replies
My truck was stolen over the weekend. Fortunately, it was recovered but they broke the key lock on the steering column and I'm having a hard time getting it started. I can turn the ignition all the way to the start position with my key or a screwdriver but the starter never engages. I'm sure I'm missing something simple but I can't seem to figure it out. Looking for instructions on how to get this started again?
View 14 Replies
Maybe its just my freaking OCD but on my 2015 f250 that I've owned since new the trim around the steering column doesn't line up directly with the dash! Not the steering wheel to the steering column trim but the column trim to the dash/instrument cluster. When I lock the tilt/tele lever in, the right side of the column lifts up maybe a 1/16th to maybe closer to 1/8th of an inch and it irritates me because the two lines to match up evenly. Is this normal for this design tilt/tele steering column? Is it normal? You can see the right side is just a little higher than the left side...
View 10 Replies
I'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 Replies
