2000 Ranger 2.5L. Recently driving up and down road to work about a half hour in to drive the battery light will flicker especially if under a load (AC on, lights on)etc... Assuming it is the alternator/voltage regulator getting ready to FAIL. Plan on replacing alternator this weekend? What to do or check something other than replace the alternator?
View 5 RepliesI was messing with the battery in my 200 Ford Ranger the other day and must of arc something. I know this because after plugging my battery back up my radio fuse was blown and my alternator was killed. I replaces the radio fuse, that works now, and got a new remanufacted alternator (tested mine at Advance it was dead). I installed it and nothing changed. The battery still wasn't charging. I know the battery is good because I tested it at Advance Auto. I took the alternator back and the shop replaced it with another remanufacted one. Same thing, installed it and the battery doesn't charge.
This time I took the alt back off and had it tested at Advance. The alt was dead. So I don't know if the part store gave me TWO bad alternators or if my truck is killing them. I find it hard to believe it could kill them immediately but my automotive knowledge is not that vast. I took the second (third counting my original) dead alternator back and they gave me a brand new one no extra charge. So I don't want to put a brand new alt in my truck and it kill this one too because I doubt they will give me a fourth one. What is going on? Could it just be as simple as I got two bad eggs?
I have 2005 Ranger 4.OL just recently when I accelerate the battery light comes on. No light when driving normal. Stopped by O'reillys had them check the battery, alternator, starter. They said battery bad. So I dropped 130.00 on new battery. Light still comes on when accelerate.
View 6 RepliesI have a 97 Ranger with 4.0 V6 with about 120,000 miles. The battery light came on today so I took it to Advance Auto to check the battery and Alternator. They said both were good. I checked the fuses and relays and nothing was blown or out of place. Could it be a bad ground?
View 8 RepliesThe battery light in my well used 1997 Ranger came on a few weeks ago. Only use the truck on the weekends. Battery reads 12v. Alternator putting out 14v. Replaced terminal clamps as they were in bad shape. Light is still on.
Weak battery possibly? Does it need to read higher than 12v for the light to be off, I wonder?
my 03 ranger 4.0l was working properly and all of a sudden I am having an issue. The battery light is on, and the volt gauge is just above L. With my multi-meter I am showing 14 volts on the output stud on the alternator, and 13.5 volts at the battery while idling. When I turn the lights/fan on I show minimal draw at the battery. Not sure if these are good checks but I figured a good place to start. Where/what should I begin checking?
View 2 Repliesso this is my pops truck and its got 95k miles seems pretty clean. But it some times has a small miss fire at idle or when i put it in drive with the break on. and its just one cylinder thats missing. So iv tried new cap rotor plugs and wires but still not luck. and did a ohms test on the injectors and there all good...
View 10 RepliesSo my 99 2.5 rcsb has been stalling out under loads, particularly when the A/C is on. It's stalled when warm, cold, engaging Drive or Reverse, and it steering does it at least once a day. There's a missing elbow to a vacuum line at the driver side (looks RABS related). The truck had the CAT melt off and now it's laying in my bed with the O2 sensor, don't know if that relates.
This truck sees 100 miles a day through the mountains, 5-7 days a week. It only has 140,000 miles on it, I put 40,000 on it in the last year with no issues. The truck is very much showing age (needs almost everything), but I'd like to keep the basics going.
I have a 98 4x4 with 145k miles and 4.0 OHV. Symptoms are as follows;
Uses ALOT of oil. 1 quart per 230 miles. Burning bad in rear cylinders, some in middle cylinders, none in front cylinders. Screams intake or PCV issues to me, not rings or valves. Never any smoke, not even on startup. No significant leaks. MPG always 18-20mpg.
Slightly rough idle.
Miss under load below 2k rpm. Not a terrible miss, but you can feel it. Has never lit the CEL. I know the CEL is good.
Never loses coolant. No coolant in oil or vice versa. Haven't done compression test, but doesn't seem like they ever tell you much anyway.
This weekend I replaced all intake gaskets, plug wires, cleaned oil residue off and regapped plugs (they are 3 months old), injector orings, and PCV valve. Flushed and burped radiator.
It's too soon to tell on the oil consumption, but I thought the intake gaskets would have cured the rough idle and misfire. The idle IS much better, but still not perfect. But the low rpm load miss is actually worse now. Still no CEL. Could it be storing codes without lighting the CEL? Also, how do you clear codes on these, can you just disconnect battery, or do you have to clear them with a scanner?
I have a 2000 ford ranger 4.0L v6. My problem is the abs light stays on and the speedometer won't work till i hit about 35-40mph.
View 14 RepliesI have a '94 Mazda B3000 3.0L V6. The engine finally gave out at 244,000 miles. I had a used motor installed with approx. 110,000 miles on it. I now hear a knocking sound only when the engine is under load (in gear and accelerating). The knocking is not present while revving the engine while in park or neutral. The transmission was rebuilt last year about this time. I have described this problem to several respected mechanics and they don't know what it could be. What could cause this condition?
View 12 RepliesSold my mazda and got a nice 2000 2wd Ranger XLT with a 3.0L. Today the wife I and took it to town, 10 miles on the highway there, a couple in town and 10 back, didn't notice anything unusual. However I haven't this truck long so I'm not sure what is usual.
Parked it for a few hours and when went out to change the front turn signals to LED I noticed the ABS light was on when I drove it into the garage...
I checked fluid, connections and fuses, no change.I go ahead and swapped the bulbs while letting things simmer, I've had so many of these Fords sometimes the easy fix comes to me.
I backed it out and took it down the road, right away I noticed my speedometer wasn't working, so I let off the gas, when I re-applied the pedal I got nothing, like it was in neutral.
I downshifted to second and got her down and turned around as the O/D started flashing... (so glad because I would have hated walking back), then pulled her back in the garage to check transmission fluid and recheck fuses, including the ones I forgot earlier under the hood. I added a 1/4 qt of fluid then tried a road test again, this time there was a real long pause before it upshifted hard and the CEL came on.
I pulled the codes with my scangauge and got:
P0500
P2120
P0028
And decided I better look some things up and consult the gurus here before I do anymore damage tonight. I'm guessing that I'm looking at a tranny replacement possibly, but with the ABS light and speedometer failure I'm not 100% sure what is going on here...
My 2000 ranger with the 3.0 is only getting around 10 or 11 mpg. It's got a check engine light on but the scanner just says lean condition. The truck also has a rough idle. I've replaced the fuel pressure regulator and fuel filter.
View 14 RepliesI just bought a 2000 Ranger. I bought it at company auction for cheap because it wouldn't start. The battery was dead when I got to it. I put a brand new battery in it since it has 155,000 miles. When you turn the key to the on position, the theft light starts blinking rapidly. It will continue to do so for about 45 seconds if you leave the key on; then it will go out. However, if you turn the key to start, all you hear is relays clicking. The engine doesn't crank at all. I jumped the starter relay and the engine turns over. I have the factory manuals for wiring diagrams and diagnostic procedures.
The theft system relies on trouble codes to point you in the right direction for testing. I borrowed an Actron code reader (like you get at Autozone) and it says there are no codes. I'm wondering, though, if it only reads the SAE standard codes from any vehicle and not the manufacturer specific codes like the theft system. I have gone through a few of the diagnostic procedures with a multimeter, but it's like looking for a needle in a haystack without the codes. So far everything I've checked has come back ok. Any common issues this might be related to? BTW, I've gotten bits and pieces of info about this truck from the guys who drove it. Apparently, it just wouldn't start one day and was parked for the next several months until I bought it.
OK, got a check engine light today when I fired up the Ranger. Like I posted previously it is running kind of rough so guess I know why now.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use? Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
2000 Ranger 2wd 3.0 ... I bought my truck last summer for $1k from my neighbor, it has hit a deer so the grill is busted,front drivers fender bent up and bumper is bent all to heck. The old girl is rock solid reliable though and gets decent mileage with cruise heat and ac so I'm happy.
Anyways on to the point, I am having two big issues with it, the check engine light randomly comes on and causes it lose power sometimes at others you don't notice it. I have not been able to get codes read because it goes off every single time I go to someplace with a scanner. The light will usually go off if you floor it for a long stretch maf maybe?
The other issue is the transmission, I don't know for sure which tranny it is but the overdrive button does not work at all even though the fuses are good and when I drive down the highway second gear you have to let off for it to shift sometimes ( I've been leaning towards the valve body gasket for that) and lately it has started a horrible vibration kicking out of overdrive or just downshifting on hills etc.?
I forgot to mention it has 255k miles on it and I don't know the history besides the balljoint I replaced this week and radiator when I bought it.
Battery light came on about two months ago it would flicker. So i had Auto zone check it out batteries were good just needed a charge. so i charged them no fix so i said alright ill do the Alternator did that and then beginning of this week it happened again so checked it went back got a replacement alternator since they said it tested bad. Put the new one on and didnt change anything. Check my batteries they were reading 10v each. I charged them and they wouldn't hold a charge. so i replacement both batteries.
So i have a new alternator and two new batteries light is still on. Contacted my tech (whose a friend) he said to check the wiring going to the alt he said both wires should read 12v on constant other when the key is turned on. Tested the constant it has 12v other reads 6-8v with key on.
He also said sometimes the wiring on the X pipe can short the alternator? i unhooked all the wiring from the Xpipe nothing changed per battery light being on or off. So what should i do.?
Also my dash lights don't work but that's been like that for awhile (bulbs are all good).. Forgot to mention sometimes the light goes off but seems to stay on 90% of the time.
When it rains my "door ajar" light comes on and the overhead lights won't turn off. that's the common problem. i've read many threads where it says to spray liberally with WD40. i intend to do that but the plot thickens.
Usually, after a few dry days, the light goes off and everything returns to normal. Not so any more. the newest episode entails the light staying on for two weeks of good warm, dry weather. naturally i always take the bulbs out. Now, its somewhat sporadic but.... I'll try to explain since I'm still trying to wrap my mind around it.
1. light stays on, dome lights won't go off.
2. tried dome lights couple of times, still wouldn't go off
3. finally, inserted dome lights and they wouldn't come on (except when manually switched on) however the door ajar switch was still on.
4. EXCEPT when i opened the passenger door the domes came on but wouldn't go off so i took the bulbs out again.
5. that's where i am now.
Not positive but I'm thinking since the new wrinkle in established expectations that I'll probably end up replacing the driver's switch. Before I tear up the door panel i need some hints concerning removal. the door has power windows and locks (which i need new actuators but that's a different story). Is there anything I need to watch out for?
I bought a 7.3 f250 with 300k mi. It had a battery light on but didn't show any signs of trouble. Eventually started dropping volts a few days later and I replaced the alternator. The light is still on and flickers in time with the idle of the truck and sometimes goes out when I'm on the gas pedal. Some nights when the lights are on the voltage drops ever so slowly until its drained. Why the new alternator didn't fix the problem? NAPA's scanner says the truck has 12.4V at idle and 12.1V at idle with the lights on. Batteries are relatively new and test fine, dual Interstate Mega-tron Plus batteries-top of the line.
View 6 RepliesI was putting in a subwoofer earlier today, and after I put everything back together, I turned the ignition to ON just to test out the system, and all the electronics worked fine.
However, when I went to crank the engine, nothing would happen, not even a click or crank. I tried jump starting the car, and it would crank and crank and crank, but wouldn't go on. All the electronics still worked fine, but the EPC light, CEL, and battery light would be solid. While cranking, the battery light would occasionally flicker.
Got a problem with the '94 Ranger. Something keeps draining the battery. For reference, the truck is an XL, manual 4x4, 4.0L, 5-speed. I've been trying to keep driving it so I could try and diagnose the issue. At first, as long as I cranked it every day, it stayed charged up, but now it has gotten worse. It will run down in an hour or two. I know figuring this kind of problem out is tough, but I thought maybe some others of you may have experience in this area that might benefit me.
Based on a gut feeling, my first idea was that there was something going on inside the AC compressor. So, I disconnected the compressor, but that wasn't it. My plan at the moment is to replace the wiring harness between the battery and the starter. The current harness is pieced together (not my doing), and whether it fixes this problem or not, it needs to be done. Another thing I've thought about is the ignition switch. It acts "funny" to me, but it has never really given any trouble.
My son needs to take this vehicle back to college with him in a couple weeks, and I need to get it figured out.