I have 2005 Ranger 4.OL just recently when I accelerate the battery light comes on. No light when driving normal. Stopped by O'reillys had them check the battery, alternator, starter. They said battery bad. So I dropped 130.00 on new battery. Light still comes on when accelerate.
View 6 RepliesI have a 97 Ranger with 4.0 V6 with about 120,000 miles. The battery light came on today so I took it to Advance Auto to check the battery and Alternator. They said both were good. I checked the fuses and relays and nothing was blown or out of place. Could it be a bad ground?
View 8 RepliesThe battery light in my well used 1997 Ranger came on a few weeks ago. Only use the truck on the weekends. Battery reads 12v. Alternator putting out 14v. Replaced terminal clamps as they were in bad shape. Light is still on.
Weak battery possibly? Does it need to read higher than 12v for the light to be off, I wonder?
2000 Ranger 2.5L. Recently driving up and down road to work about a half hour in to drive the battery light will flicker especially if under a load (AC on, lights on)etc... Assuming it is the alternator/voltage regulator getting ready to FAIL. Plan on replacing alternator this weekend? What to do or check something other than replace the alternator?
View 5 Repliesmy 03 ranger 4.0l was working properly and all of a sudden I am having an issue. The battery light is on, and the volt gauge is just above L. With my multi-meter I am showing 14 volts on the output stud on the alternator, and 13.5 volts at the battery while idling. When I turn the lights/fan on I show minimal draw at the battery. Not sure if these are good checks but I figured a good place to start. Where/what should I begin checking?
View 2 RepliesMy ranger is an 89 but it's got a 91 motor in it, 2.9 V6. When I accelerate it hesitates before actually accelerating which makes me think the TPS is bad. Probed and tested and I got .85V throttle closed and 4.65 at wide open. Specs call for .8V - 4.5V
I'm not sure if there's an allowance of fluctuation, but is that high enough to point out a bad TPS? If it's not the TPS, is the ignition timing off or what else could it be?
Whenever I slow down for a car to turn or accelerate after a stop sign the ice cold air goes away and is replaced by warmer air but then it never turns back cold. Only when I kill the engine and start back up does it return. I just had the Freon refilled and there are no leaks.
View 3 RepliesAs said vibration at idle, as I slowly accelerate (in park) the vibration is worse at 1200 rpm, then keep slowly accelerating and at 1800 rpm completely goes away. Doesn't seem like a miss almost like a balance thing. Also when in gear and accelerating it doesn't seem to be there unless I just don't feel it when moving.
View 5 RepliesIf I hop in my truck right now (1994 3.0 ford ranger 5 speed) as soon as i accelerate half pedal or more it'll bog down really bad. Usually in second gear it does it the most and ill shift to third gear and it still jerks and has trouble accelerating. If I let the car sit for 10 minutes and then go drive it it'll jerk and bog down a little bit but no where near as much. usually only does it for the first couple minutes of driving then goes back to normal. I also noticed that my temperature gauge is always right before NORMAL. Also I'll have to give it a little more gas right before i go to drive or it'll want to stall but as soon as i get into driving it, it acts perfectly fine.
View 7 RepliesI have a 97 ranger 4 cyl that's been making a whistle noise the last few weeks. The sound is literally like a whistle and the noise level varies but its never obnoxious or loud. The sound does not happen when truck is idle, seems to happen mostly when I first accelerate and slow down although sometimes it does happen when I am going 20-30. it doesn't happen all the time but lately its happening more. What this could be? The truck idles and runs great.
View 14 RepliesI have a 98 ranger, 4x4, 5spd 3.0 with 88k miles.
While I am driving it, everything is great, but when i start to accelerate, or torque the engine (going up a hill), I get this clicking/vibration in my gas pedal. its extremely noticeable, by feeling and ear.
Its most common around 2k to 2.5k RPM. There is a lot of play in the throttle cable, about an 1" or so give untill you feel pressure. What I need to replace or tighten?
Got a problem with the '94 Ranger. Something keeps draining the battery. For reference, the truck is an XL, manual 4x4, 4.0L, 5-speed. I've been trying to keep driving it so I could try and diagnose the issue. At first, as long as I cranked it every day, it stayed charged up, but now it has gotten worse. It will run down in an hour or two. I know figuring this kind of problem out is tough, but I thought maybe some others of you may have experience in this area that might benefit me.
Based on a gut feeling, my first idea was that there was something going on inside the AC compressor. So, I disconnected the compressor, but that wasn't it. My plan at the moment is to replace the wiring harness between the battery and the starter. The current harness is pieced together (not my doing), and whether it fixes this problem or not, it needs to be done. Another thing I've thought about is the ignition switch. It acts "funny" to me, but it has never really given any trouble.
My son needs to take this vehicle back to college with him in a couple weeks, and I need to get it figured out.
Is there a fusible link from the alternator to the battery? The new alternator that I put on and got tested is not charging the battery. Was wondering if it could be a fusible link but I couldn't find it. Where it is located on a 2000 ranger?
Also, I put a DC volt meter on the negative side of the battery and the positive side of the CHARGING wire that would be connected to the alternator and got the same reading as if I put the meter on the positive of the battery.
Does this mean the fusible link is good?
I had my battery out for quite some time. When I put in a brand new battery my key was not recognized and my truck will not start.
View 3 Replies98 Mazda B4000 4.0 4x4
I bought this truck about two months ago and it has been great no problems starts right up and runs like a top. I was installing a 4 channel amp yesterday on and off and the dome light was on all day as the doors would periodically be opened or closed so it never did that cycle of 10 min or whatever when the lights turns off. This is what killed the battery.
I had my neighbor jump me and after a few minutes of charging it started right up and idled for about a minute long enough he left and parked, then it stalled. I started it about another 6 times before the battery died again. Every time it started fine then would idle between 1-10 sec then start to sputter and eventually die. Pressing the accelerator pedal only killed it faster.
I got a new battery today as the other charges so that I could fix it today without missing work again tomorrow. Unfortunately it does the same thing I was hoping that the voltage was just low or the polarity flipped or something on the other battery.
To sum it up the truck never gave previous symptoms just simply ran too low (battery never DIED the lights came on just clicked when starting) on power and now stalls when started which it does immediately no long cranking.
The twist; truck has an aftermarket alarm by Python. Problem is I don't know anything about the alarm or if it comes with an immobilizer. I am in the process of trying to figure this out but need to pull dash or something to find the "brain"? Never had an alarm like this I disconnected the clear square that adjusts the sensitivity hoping that was it but I don't know where or what I assume the brain of the alarm is.
I have an '02 Ranger 2.3L 40k miles that will not turn over even with a good battery. When the key is inserted and turned, all the dash lights and headlights come on but the engine does not turn over. Could it be....
*Power Control Module?
*Ignition Module?
*Key?
*Whatever the part is called that reads the Key's security code.
*Clutch Switch?
I am trying to avoid getting the run-around at the dealer and be able to drive to work on Monday!
I just finished putting in aftermarket A/C in the 2004 Ranger my dad gave my son. It's a 2.3L, STD transmission. It was running GREAT before the project started. I installed new battery as part of the project. When I started it back up it ran for 2 or 3 seconds then died. I now cranks, but does not fire at all.
I have tried one of the key reprogramming sequences (turn key to "ON" 8 times) with no success. Would it crank at all if it were a key security issue? Is there anything I need to reset anywhere else, like in the air intake system?
It's either not getting spark or not getting air. The fact that it ran for a couple of seconds has me confused. Would it run at ALL if there was a key security problem?
I had to remove and reinstall the air filter housing and ducting. Is there anything else I need to do to with the air intake system?
fuse #11 in the battery junction box under hood keeps blowing, the last time I put a fuse in it blew immediately, key was off and lights off. Fuse is for parking lights, dash light and I/P(whatever that is) and switch illumination lights. I have to start following all wires to find bad spot. May just put in piece of metal and watch for smoke...
View 3 RepliesI was driving around town and I kept noticing my aftermarket radio would shut down and turn back on when I put my foot to the floor, then I noticed that my voltage gauge would shoot to the H when I hit around 3000 rpm and all the dash light's and head lights get brighter but once I let off the throttle it goes right back down. I've been taking it easy lately and now around 4000 rpm it will shoot up now. But I just replaced the voltage regulator I checked the battery and cables they don't seem to be damaged and I already replaced the belt. What could cause this?
View 3 RepliesI have a 96' ranger that has been missing quite regularly. The vehicle has over 200,000 miles on it, but has been taken care of regularly by me since 75,000.
Problem: When I start the vehicle, the engine takes a little bit to find the idle. It spits and fumbles around some until it finds a somewhat rough idle. Often, when I first start driving in the morning, the vehicle really jumps around due to misfiring. Even after running smoothly for awhile, the vehicle with sporadically misfire with no rhyme or reason. This is particularly true when climbing a grade. When sitting at a red light and idleing in gear, you can definitely feel the truck shaking from side to side. Also, when idling in gear, the battery gauge on the dash fluctuates, but when the vehicle is in park the battery gauge doesn't fluctuate...it just idles a little rough.
I had the Ranger to a garage and had them check the battery and alternator connections and ground to try and figure out what is making the battery gauge fluctuate...alternator and battery checked out...no diagnosis for fluctuation.
I replaced all plugs and wires and also checked the coil pack. One of the coils (#6) had some build-up in the top. I cleaned it out and replaced all the plug wires and everything snapped in place and fit fine.
The garage did tell me that an error code came up with the EGR valve and or sensor. They didn't seem to concerned about it. Do the EGR valve could be the cause of all the stuttering and misfiring going on with the ranger? I really don't know where else to look. Maybe replace the coil pack?
I was messing with the battery in my 200 Ford Ranger the other day and must of arc something. I know this because after plugging my battery back up my radio fuse was blown and my alternator was killed. I replaces the radio fuse, that works now, and got a new remanufacted alternator (tested mine at Advance it was dead). I installed it and nothing changed. The battery still wasn't charging. I know the battery is good because I tested it at Advance Auto. I took the alternator back and the shop replaced it with another remanufacted one. Same thing, installed it and the battery doesn't charge.
This time I took the alt back off and had it tested at Advance. The alt was dead. So I don't know if the part store gave me TWO bad alternators or if my truck is killing them. I find it hard to believe it could kill them immediately but my automotive knowledge is not that vast. I took the second (third counting my original) dead alternator back and they gave me a brand new one no extra charge. So I don't want to put a brand new alt in my truck and it kill this one too because I doubt they will give me a fourth one. What is going on? Could it just be as simple as I got two bad eggs?