I did some errands in 2000 Explorer and sometimes crossed car symbol appears on dashboard.
I cant see it in user's manual. I surfed internet to get the answer and just found the same caution with picture.
This is link ....
What is that?
I am having a problem with my dashboard lights blowing fuses. I bought an 87 Ranger XLT, and found that the dash lights didn't work. The 5 amp dash light fuse was blown, and the dome light would not come on using the switch. I replaced the fuse with a 15 amp and replaced the headlight switch which had melted the connector at one of the terminals. The dome light now comes on using the switch and I was able to get the dash lights to come on at a very low setting, but the headlight switch will smoke some.
But when I turn the switch to brighten the dash lights, it causes the tail light fuse to blow. I don't see how the dash lights could blow the tail light fuse, but it happens as soon as I install a new fuse and brighten the dash lights. What is going on? I think it is probably a short somewhere, so I pulled the instrument cluster and looked at the wires, didn't see anything exposed.
In my 1999 Ranger, I can flip the air outlet switch to cause the air to exit either up, down, or straight out -- except that most of the time the air WILL NOT come straight out the dashboard ducts. I am assuming that there is some kind of diverter valve inside the dash that is intermittently working, but I do not know how to get to it. Do I remove the radio panel? If so, how? Or is there a way to get to it some other way, like from underneath or through the glove box? Does it just need a shot of WD-40 to free it up?
View 7 RepliesI bought a used 2008 prius about a month ago with 44,000 miles. Tonight when I went out to get something out of the car, I noticed a flashing light on the dashboard. It looks like a car but is flashing so quickly I am not certain. I can't find anything about it.
View 4 RepliesI have a 2000 Ranger 4.0L manual transmission. I just replaced the starter/solenoid on it a few days ago. I went to start it, and I got 1 click and the whole system goes dead (ie: lights, instrument panel, everything!) I checked all the fuses and the starter relay in the fuse box. All good. I tested the battery, it's charged and good. I even tried jumping it. Same problem.
I can remove power from the system, re-apply power and same issue. I'm not even sure where to start here. I checked the ground terminal on the battery. It's connected to the frame and clean. Cables are tight to the battery and clean.
What am I missing?
2008 Suzuki XL7 Luxury FWD105,000 miles3.6L 6 cylinder engine
The "buckle seat belt" symbol keeps popping up on the dashboard for the driver's seat even though the seat belt is certainly buckled. This happens off and on throughout a drive, but it does happen at least once every time the car is driven. Other than the constant dinging and the dashboard light, the seatbelt seems to be working properly.
We took it in to a mechanic and they said it is a switch in the seat belt assembly that is failing, but they don’t sell just the switch. They have to replace the whole assembly. They determined this by doing an electrical test in which they compared the resistance of the working passenger seatbelt to the non-working drivers seatbelt.
We are concerned that this is a problem that would cause the seatbelt to fail in the case of an accident. If we ignore this problem and just have them shut the seat belt warning sound OFF, are we in danger? Basically I just want to know how critical is this problem?
2000 ranger 3.0 auto 4wd hard to shift. Are the cables known to stretch?
View 6 RepliesI am experiencing Dismal fuel Economy, I filled the tank about 16 gallons (tank read full) and went 118 miles, I burned to about 1/4th of a tank remaining, so a rough estimate is I burned 12 gallons of fuel to go 118 miles, leaving me 5-8MPG Cruising 50-60 miles an hour.... What should I be looking for..... I have 110,7XX on the truck. it's slow as heck, it hesitates and just has no get up and go unless you really step on it. It's had a recent tune up.
Plugs were changed at 105,000 miles roughly.... I'm at a loss to know why this little truck is burning so much fuel. It's the 6 Cyl Flex fuel engine. with just normal fuel run in it...I've looked at night for arcing wires and there's no flashes... there is no real miss, I checked the intake for pirate air and fixed one minor leak and have recently rechecked it as well...I've not pulled the plugs out again yet....
This has been an issue for about 8 months now. I'm getting a misfire on cylinder 4. So far compression test, new gas filter, fuel injectors cleaned, spark plugs and wires replaced. coil pack replaced. Heater valve was leaking but was replaced.
View 10 RepliesI replaced a cracked radiator with a new one on my 2000 model B2500 a coupla' days ago, guessing at the refill, as I just got the truck and don't have a manual. Guestimate was pretty close, but I got some weirdness from the temp gauge for a bit. Temp gauge read cold (even though it was maybe sixty degrees outside) after idling for quite a bit, but would rise to operating temp if I ran the RPM's up a bit, then fall back to cold when I let it drop back down to idle.....never rose to above normal operating temperature, though.
I took a short drive down the road, stayed at normal temp, but dropped back down to cold when I parked it. Taking a peek under the hood, had air blowing out into the resevoir, bubbling like bathtub farts. All appears to be normal today, but I've gotta' take this truck for a roadtrip in a coupla' days and would like to make sure I ain't missed a step that'll send me hikin'.
What is the process of burping the radiator so's I can be sure it's all good?
OK, got a check engine light today when I fired up the Ranger.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use?
Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
2000 Model, The fuse keeps blowing on this. I thought it was the cruise control fuse because the cruise kept not working and when I replaced fuse it would work. Only for a little though, then I looked at manual and it says the fuse is for the brake position switch. I am presuming this is just like the old days and that is the brake light switch under the dash. They use to have two wires now there is like five. Anyways I do not see any bare wires or anything that would blow a fuse, is it common for these switches to go out or what??
View 13 RepliesMy buddy bought this 2000 Ranger 4x4 with the 3.0 and 150,000 miles for 500 bucks. After he bought it, the number 2 spark plug boot caught on fire, and turned completely to ash. So we parked the damn thing, and have been training ever since, but it did run when we parked it. We replaced all plugs, wires suspecting a bad plug (and they were all fouled). Went to start it and now its on the verge of starting, but can't quite get there. So here's what we've done since.
-Replaced coil (had it tested, failed primary test on terminal 1, and secondary on 3 and 4)
No change
-Checked Spark by grounding spark plug
Good
-Checked Fuel at rail
Good- Held until empty, primed Fuel system (key on for 3 seconds 5 times) checked again, good)
-Truck had been sitting for three months, so put in small bottle of stabil and added 5 gallons with Lucas. Primed the system about 20 times, and tried to start. No effect.
-Checked battery.
1 bad cell, 3 low on water- replaced battery. Allowed it to crank for longer (before we were jumping it) but still didn't want to.
Note of concern : After we replaced the battery and went to start it, when the key was disengaged I noticed a hissing sound coming from the radiator cap. The truck is in Upstate new york and hasn't been ran in 3 months. I'm hoping its not but thinking it is a cracked jacket or a blown head gasket.
I have a 2000 ranger and the right low beam went out, we changed the bulb to no avil. I thought it might be the light switch so we changed it also ,nothing!! We have checked the only ground, I can find for the lights (on the driver side under the fuse box under the hood). This problem has me stumped . Another problem that may or may not be related is the cargo light does not work either...
View 8 RepliesWe have a 2000 ranger 2wd with a 5 speed transmission, we just had new tires put on last Sunday and on the way home it had a vibration in 5th gear at 55 mph whats so strange about it is, in 4th gear at 55 mph. it don't do it but when you shift it to 5th and hold it at 55 it starts.
I have checked the drive shaft and even put it on stands and shifted through the gears and held it at 55 no vibration, I guess because there is no load on the drive train. the truck only has 56,000 miles on it.
My parents 2000 Ranger has an CEL for cylinder 4 misfire, but it will clear on its own and then start up days/weeks later, is this common? Could it be an injector?
View 3 RepliesI have a misfire mystery going on in my girlfriends 00 ranger. What is going on, is there is an intermittent misfire on #4. I have an ultra gauge hooked to it, so most of the time when it does it, it will flash a pending code. A lot of the time, the pending code will go away, but sometimes it will set the PO304 code.
First I tried a tune up. New plugs and wires, air cleaner, cleaned out the throttle body. This cured it, for a short while. Then we were back to the pending code / setting code for #4.
When I pull the plug on #4 it is sometimes wet with gas. If you put a new plug in it runs fine for a while. In fact the last time we took a several 100 mile trip with it right after plug change, and it ran great. The pulled plugs re always in good condition with no burn, oil, chips or glazing. I have been using the standard autolites that are in advance auto's computer for that engine. No issues with the other 5 so I figure they re good enough.
The day after we came back I get the call... Honey its doing it again. Often to the point of having no power at all.
But it will clear itself usually, if not a new plug for #4 will cure it immediately.
So I thought something is killing this plug.... Or flooding it. SO I ran 2 cans of sea foam though it, put in a new plug and an new wire. It fixed it for a week then it did it again.
Ok I think... maybe the coil pack is bad either killing the plug or just not firing it at all? So since the pack has never been change in its nearly 300K life (to my knowledge, shes had the truck since about 60K) What the heck.... a new coil pack for the old thing.
I have not had the chance to clean the MAF but we are talking misfire on one cylinder, every now and then with no real conditions that set it off. More often than not its a pending code that you can even hear or feel and other times its a full blown miss that drags the truck down. Well for a short while until it clears up or I replace the plug.
3 cans of seafoam surely would have cleared a sticky injector. I realize it could be a bad wire to that injector but I have not had the time to tear the fiddle bits off to get to it to clean and test it... or just replace it.
Honestly Ive had a lot of cars and trucks, I don't remember ever having to replace an injector. Ive had bad wires to them but they misbehave ALL the time. This problem is so intermittent its freaky.
She says it does it mostly when its cold or not totally warmed up. Almost always, by the time the engine is hot it goes away.
And hot for this truck is over 185F, which I think its too cold to be running and the thermostat needs changed BUT she thinks cool=good. I keep telling her no, cool is often not good, the engine needs to be up to the operating temp.... which to me means 190-200. Her ranger runs between 170-180 all the time. I doubt thats causing the problem but still.... I think new thermo is in order.
My thinking is since it runs so cool all the time, the issue might be related to a spike in the temp over 180 ish, that gods forbid is opening a crack somewhere to suck air or lose compression.
And a compression test is my next step on #4 if/when it does it again. Now I have had cracked valves before, I don't recall them acting this way. After all sometimes the thing will go 100s of miles under different driving conditions and run fine. I don't think a cracked valve would be that nice.
Shes getting @18 MPG mixed driving, when it runs t runs like a bear. It always fires right up. There is no smoke, white or black. There is no water in the oil, no oil in the water. No audible exhaust leaks. No ticks knocks or oddball noises. For its age and miles almost 300K it runs perfectly.
Well until it has its intermittent issue with the misfire, that isnt bad enough to actually set the code.
I have a 2000 Ranger 4.0L with intermittent no start. Have spark, fuel pressure is 55psi, temp sensors are reading correctly. When there is a no start condition I can pop the scharder valve, relieve the pressure on the fuel rail and it will start.
View 3 RepliesI have a 2000 ford ranger 4.0L v6. My problem is the abs light stays on and the speedometer won't work till i hit about 35-40mph.
View 14 RepliesI have a 2000 Ford Ranger 3.0L engine, 2 wheel drive, with automatic transmission. Check engine light came on about 3 months ago. checked with scanner and P0401 EGR flow insufficient came up. cleared it and it came back. truck seems to be running fine. I didn't take autoshop as a kid, so i probably will need a little hand holding on this one.
View 14 RepliesAbout a month and a half ago I was doing 70mph down the highway and the truck began to lean out sputtering and sounding like fuel was not getting there, when I pulled over on the side of the highway because it killed itself and then the car would not start I noticed the ox sensor for the 3rd cat was ripped out from being caught on the driveline, I removed ox sensor and car still wouldn't start. I took the truck to my buddies shop and after a new ox sensor was installed with some effort the truck started 30minutes later, I did not think this was reason for the truck to not start but after a day it was running like a top again, little did I know. Last week driving down the highway ironically in the same spot as before the truck did the same thing sputtered to a stop and would not restart.
Side Note: on both of these occasions after the truck would sit for a day it would start run for about 5 seconds and die???? So I had it towed home again and began reading FTE, I saw posts about fuel pressure and spark and P0176 code for Flex Fuel, Inertia Switch and so on.
So I started with Fuses they all look good then the most popular post and 2 of the codes were P0176 and P0177 for flex Fuel they read OBD II flex fuel wont start....Another code was for EVAP and 3 codes for heater bank(it turned out to be a fuse but is or could something trip this to send the car down this path?
I Then figured I would try the Fuel Filter..This did not work.
2nd I tried was Fuel pump pressure is good based off others posts.
So I bought the Flex Fuel Replicator that eliminates the need for the flex fuel sensor, from the guy in Portland, well this didn't work either. Next I went to spark checked all plugs they smelled like gas and were slightly fouled I had just replaced these about a year ago but hell why not? so I replaced and got nothing still also checked the oil had some gas smell to it but my buddy said this was normal with trying to get it to turn over without success.
Checked inertia cut off it was normal, checked fuses they were good(except heater which has been replaced). Now I am stuck...