Ford Ranger / B-Series :: 1999 - Dashboard Air Duct Does Not Switch Properly
Mar 28, 2015
In my 1999 Ranger, I can flip the air outlet switch to cause the air to exit either up, down, or straight out -- except that most of the time the air WILL NOT come straight out the dashboard ducts. I am assuming that there is some kind of diverter valve inside the dash that is intermittently working, but I do not know how to get to it. Do I remove the radio panel? If so, how? Or is there a way to get to it some other way, like from underneath or through the glove box? Does it just need a shot of WD-40 to free it up?
View 7 Replies
Advertisement
I have a 1999 ford ranger and I believe my Clutch safety starting switch is going out. Some times I push my clutch in and truck starts fine other times it will not turn over so I stomp clutch and then it starts. My question is, is there any way to bypass this switch?
View 5 Replies
I got a 1990 bmw 735il and I'd like to know how to properly switch from automatic to manual on my transmission it has the switch A to M but I don't know if the car has to be turned off or on, cause I don't want to do it the wrong way
View 1 Replies
I have an 03 Ford Ranger 4x4. Great truck and runs great just with one small problem. For whatever reason, every single time, the a/c only blows un-cool air (not hot) when I start the truck. Then, and only then, after about 30-40 mins of constant driving around does the a/c start working properly and blowing COLD air. After that it works great but it always takes about 30 mins after I start the truck for it to work correctly.
View 4 Replies
I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.
Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).
View 1 Replies
I am having a problem with my dashboard lights blowing fuses. I bought an 87 Ranger XLT, and found that the dash lights didn't work. The 5 amp dash light fuse was blown, and the dome light would not come on using the switch. I replaced the fuse with a 15 amp and replaced the headlight switch which had melted the connector at one of the terminals. The dome light now comes on using the switch and I was able to get the dash lights to come on at a very low setting, but the headlight switch will smoke some.
But when I turn the switch to brighten the dash lights, it causes the tail light fuse to blow. I don't see how the dash lights could blow the tail light fuse, but it happens as soon as I install a new fuse and brighten the dash lights. What is going on? I think it is probably a short somewhere, so I pulled the instrument cluster and looked at the wires, didn't see anything exposed.
View 7 Replies
I did some errands in 2000 Explorer and sometimes crossed car symbol appears on dashboard.
I cant see it in user's manual. I surfed internet to get the answer and just found the same caution with picture.
This is link ....
What is that?
View 4 Replies
New owner of a used 2002 Ranger XLT 4x4 (with 59k miles) here (and new to this forum). Having problems with the oil pressure gauge not registering on cold starts (though it registers after the engine warms up).
I know this is nothing more than an idiot light since the gauge isn't really a gauge (inasmuch as it registers in the normal range at 7 psi and stays there unless the pressure goes away).
I've read that this is likely due to the oil pressure switch not functioning properly. I'd like to know where this switch is located on a 4.0 L V6. Other than this, the engine functions normally (though it sucks the gas).
View 6 Replies
Apparently, top secret location of the oil pressure switch on the 1997 Ranger 4.0?
View 3 Replies
I've got a 2008 Ranger FX4, 4.0L with manual transmission. Recently I noticed that I have no reverse lights. I have to parallel park on busy streets from time to time, so this is a safety issue that I need to fix.
I checked the bulbs, both seem fine - would be unlikely that both bulbs would die simultaneously. I checked the fuse. Again unlikely unless the reverse lights were on their own independent circuit. 10A fuse looks fine too.
Last thing I can think of is a switch. I checked my Haynes Manual, there is no mention of it, which is odd, usually my manual is quite good. Where the switch is located? Any experience with swapping this out?
View 2 Replies
I have an 88 ranger 2.9 manual trans. The clutch safety switch wires melted (red with light blue) 2 come off the ignition, I traced the one to the clutch switch and replaced. My problem is my book says the other goes to " electronic shift control module", I can't find this module and I can't seem to chase wire as it gets lost in wire loom.
View 4 Replies
What is the likely culprit? No other electrical issues, brake light quit working when brake is depressed, all other lights work including blinkers/running/head. Was going to break out a wiring diagram....
View 7 Replies
My buddy's 1998 4.0L Ranger caught fire from the dreaded brake switch shorting on the master cylinder. In his defense, he's only owned the truck less than a week and had no clue of the recall. The damage is mainly to the wire harnesses on the driver's side.
Rebuild the wiring. What other years of the Rangers I can pull the wiring harnesses from? Or if the 3.0 harness will work?
View 10 Replies
The cruise control switch on my 2000 Ranger just broke. It looks like you have to remove the airbag to access it. How is that accessed? It looks like there are 2 plugs on the back of the wheel that need to be removed.
View 9 Replies
I have a 98 Ranger 2wd reg cab 2.3L 5sp. Recently the airbag warning light was blinking 2-7 which indicates bad lamp in passenger airbag deactivation switch. Since the lamp has no numbers or markings on it, and my repair manual has no schematic on that part, where I can find the ma, wattage or ohm rating of the lamp? Or a part number / source for a replacement lamp?
View 13 Replies
1985 2.3L... New fuel pump And fuel pump relay, problem was happening before new parts. the wires at inertia switch continue to get hot switch has been removed. The heat continues to under the hood where there is some so rt of connecting link and heat stops.what the is this link for, it doesn't look like A fusible link?? Saw a similar post here about a fuel pump shutting down and wires getting hot. Same problem.
View 9 Replies
I have a 2011 f150 xl with the basic climate system. I'm having a couple issues with my hvac system. Initially when I took over payments on this truck I was getting a little popping noise under the dash that would go away after a couple pops. I took the bezel off to look at the radio and how it was mounted for a separate issue when I put everything back together I started the truck and now that popping is constant (it is the blend motor actuator, I've already determine that and have a new one coming) the other issue I got is that now the ac will only blow through defrost no matter what button I push. When I start up it will blow out the defrost like the flap is in default then it will blow out of the dash for a few seconds and then go back to blowing out of the defrost. I still have speed control tho I don't have 1 ,which I didn't have before that, and I haven't tried temp yet but I'm assuming it still works. Do the newer trucks still use vacuum to control the flaps or is it all electronic? I've noticed when I look at the actuators they all have a plug end instead of a vacuum port. And would the defrost vent issue be a dash control issue or would it be the actuator for that one a
s well?
View 1 Replies
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 Replies
I went to transmission shop today and tech told me c solenoid was showing performance problem when scanned. He took it for drive and said it was commanding shift into fifth gear. It is a 3.0 extended cab 2wd with just over 200000 on truck, transmission was rebuilt just over 25000 miles ago. Fluid is so clean its still clear looking just faint red color. All other gears shift and pull great all electrical clean and hooked up, he crawled under it and said pan adjustments were tight, whatever that means.
View 14 Replies
My 99 ranger has a strange issue its got a miss when the A/C is on, when going down the road I can feel the engine sorta pulse for a second, gets better the more I drive it, its got all new plugs and wires, not sure where else to look?
View 1 Replies
Just purchased a 1999 4.0L 4WD, when I select 4WD Hi or LO sometimes it will go, sometimes it won't. Now the 4WD Hi and LO lights are flashing intermittently while I'm driving. At one point the Hi light burned and wouldn't turn off.
View 14 Replies
