I have a 2001 Ranger 4.0, 4x4 that just hit 100k and the oil pressure gauge doesn't show a reading for about 1 minute after startup. Also, the check gauge light comes on. What do I replace to fix this and is it something I can do myself? I am mildly handy. Would you worry about fixing it or just let it go because it's obviously getting oil pressure.
View 2 RepliesI have a 2002 Ranger V6 3000 with 100K miles. Can I add a higher viscosity oil since my pressure gauge is acting up. I changed the sending switch twice but the gauge still acts up occasionally. I was thinking of adding 10/ 30 on my next oil change. I do live in the area where the air temp is quite high in the summer. The truck runs well except for the oil gauge, in my opinion, is giving false readings.
View 14 Replies1991 Ranger STX, 4.0. Had a leak from the rubber seal on the thermostat. Changed the thermostat (stat 195) and seal. Now my temperature gauge is not showing a constant reading, goes to half way and when the thermo opens the gauge falls down to a quarter. The gauge is cycling this way every time the thermo opens.
View 2 RepliesI have a 97 Splash with the 3.0, oil pressure goes up to about the middle of the gauge after startup, however, it stays there whatever I do, warm/cold, idle/5500 rpm. Is it supposed to be like that?
View 4 RepliesMy oil pressure gauge does not work. I was told that it's most likely the sensor. Where would I find this to change it out?
View 3 RepliesI have an 87 Ranger and the oil pressure gauge is slow to respond changes in pressure. Is this the way the gauge is designed to work or do I have a bad sending unit?
View 4 Replies2001 Ranger, 108,000 miles, good regular maintenance per the Ford Schedule. 4.0L manual trans.
I changed the fuel filter 20,000 miles ago. This has been a recurring issue anytime my fuel level was low, about 1/4 tank or less, and when the truck was warmed up, hot. The fix in the past was to add fuel and let the truck sit for awhile. Now, today I drove home for lunch and when I tried to start the truck to return to work, it wouldn't start.
Same conditions, low fuel level and it was warmed up. The engine will turn over and start to run with ether in the air box, so it's definitely fuel related. A fuel pressure gauge on the Schrader valve got a zero reading, not even a flicker, and no residual pressure after shut off.
Could this be only a fuel pressure regulator issue? Or should I prepare to replace the fuel pump? Is there a fuse that might be blown?
These are my gauge readings at 70 degrees Fahrenheit. According to an AC conversion for gauges calibrated in Pascals, 35-40F converts to 241-276 KPa, 140-160F converts to 1000-1103Kpa. The gauges are in Mpa which by conversion is 3 decimal points to the left so .241-.276 and 1-1.103 Mpa. Here are my gauge readings at 68 degrees ambient temp. Rear air is same as an ambient temp on max ac and the front is pictured. There seem to be virtually no pressure differences which I would interpret as a novice that there is ) freon flow.
There is freon in the system with the high pressure being approx correct but the low side is too high if I understand correctly. Basically when at highway speeds at 75 degrees yesterday the front AC was cold and the rear was outside vent temp only. There are slight leaks in the low and high-pressure valves. I have a Mastercool replacement tool but they did not send a fitting for the high-pressure valve. What these readings mean as far as what may be wrong?
I have been having an intermittent (2 times in the past 2000 miles) oil pressure gauge not reading. As I own a 6.0L I understand that this is just a pressure switch in reality and if the engine was starved of oil the HPOP system would kill the engine. The first time the oil gauge went out it was raining out. The second time was after going through a carwash and getting the underbody wash. At this time my battery light also came on for a few seconds.
Both problems seemed to go away after an engine restart. Today it is snowing lightly and my battery light came on again. I happened to be monitoring the battery voltage and FICM voltage via OBD II using Torque app. At no time while the battery light was on today did the battery voltage drop below 13.5V. The FICM was also stable at 48.5+/-.5V.
As the battery voltage read by the PCM is not actually dropping and the previous oil pressure gauge and the fact that my left blinker indicator is out I am thinking I may have electrical issues with the gauge cluster. I have never had these issues while driving in dry weather. Where do I start troubleshooting this? Also I am going out of town for the next two weeks and my girlfriend was going to use the vehicle. Is it OK for her to drive?
Dad has a 2001 well cared for Mazda B3000 with around 128,000 miles on it. Motor runs fine, so did the tranny up until a couple of weeks ago. The tranny needs a new clutch, throw out bearing, and pressure plate. It was drivable up until about four days ago.
My Dad has been working 6-7 days a week and hasn't had time to tear into the tranny. We just drained the old fluid out and put in new when it first started making the noise it makes. We have priced the parts and was just waiting for my Dad to get a weekend off to tackle the problem. But someone at work told my Dad to bleed the slave cylinder before he tore into the tranny, just to see if it would work.
Well we bled the slave cylinder just like you do brakes. But now the clutch has no pressure, it just goes to the floor. We have tried everything. My dad uses the truck to commute back and forth to work. So, I am looking for any tricks on how we can get pressure back in the clutch so he can get to work.
Just changed the fuel filter in my '04 6.0, no issues worked just like normal, filter primed truck started, great. Well now my fuel pressure gauge is reading dead 0, I know that can't be right because the truck is running, but noticed my fuel mileage seems about 2 mpg lower all of a sudden. Had R&R Injectors installed about 40k ago, figure it's just a bad gauge but wanted to check and see before messing with the frickin wiring. Also, have had a lot of pressure buildup in the coolant tank, has had head gaskets and studs, anything else it could be besides head gaskets? Have had a lot of wiring issues with this truck from the previous owner....
View 14 RepliesCan I read oil pressure on my scan gauge II ? If so, how do I do it?
View 14 RepliesI have a 2001 F150 Supercrew (5.4 V8, 2WD,Auto trans) and recently when we fill the gas tank, the fuel tank doesn't go all the way up to the "full" line. Don't know if this matters but: about a year 1/2 ago in a little town (while on vacation), we broke down and the trouble was the fuel pump. The little town did have a small auto-parts store, and luckily had the fuel pump we needed. Unfortunately we didn't have much as far as tools and we wound up tearing/cutting the filler hose and the vent line.
The little auto store did not have the correct rubber filler & vent hoses for my truck and would take a few days get in stock. We changed out the entire fuel pump and sender unit, and were able to modify some rubber hoses for a new filler & vent line hose. Everything worked great for a year 1/2 but in the last few weeks we have noticed that when we fill the tank, the gas gauge does not go all the way up to the "F" line to show full. With the price of gas, it is important to know exactly how much is really in the tank. Also, is there a battery in the ceiling console for the temperature and compass? Ours just stopped working yesterday.
I just tried doing the self test for reading the codes via the check engine light with the OBD1 system on my '93 4.0 Ranger. Problem is: When trying to mark down the flashes of the check engine light, they flash so erratically and rapidly that there is no way to accurately count. At times the light flickers so fast it never even gets to get fully bright enough to tell if it is actually a "flash" or not. I'm (again) trying to diagnose an issue with the truck starting and running fine for about 3-4 minutes and then like flipping a switch begins blubbering and belching out black smoke, check engine light flashes on/off randomly, then the engine will eventually die. It will restart provided the ignition switch is turned all the way off and attempted again, generating same results only within 30 seconds or so. If you try restarting w/o turning the ignition all the way off, it'll spin over but won't start. ECM?
View 4 RepliesI changed the seal on the tank filler neck, now I run out of gas at 1/4 tank. How to "reset" the gauge?
2001 3.8 V-6 5-speed
Twice in the last year my 1999 Ranger (@138,000 miles) has started running very loudly: I checked dash and see oil pressure gauge says no oil pressure. First time this happened, I pulled over, had it towed. At garage they start it up: gauge normal, they check oil says its OK. I take it to the dealership, they replace sending unit, but can't explain why it was running loudly. Today same thing happens: I checked oil pressure gauge, it's OK. After an hour, starts running loudly, gauge in red. Park car for 15 - 20 minutes, start it up: all is well: gauge OK, running quietly. This is amy 'spare' car, so it only gets driven 1 -2 times per month, short distances.
View 4 RepliesGas gauge went from about 1/4 to full in about 3 seconds and hasn't moved since. 2000 B3000 Mazda 3.0 V-6 auto. I've checked all the instrument cluster fuses (11,26,33). I know of the method of disconnecting the connector at the gas tank to see if its the sending unit or the gauge but I can't see or feel in there good enough to do that. Would either one go bad that quickly? Doesn't seem likely to me.
I've read about a "slosh sensor" in a post on this forum - does my truck even have that? I've had an intermittent wiper problem a couple of times but the multifunction switch wouldn't be involved would it? I'm just trying to see if there might be a simple fix before I add it to my repair list when I take it to have the ball joints replaced.
I have a 94 Ford Ranger, 2WD, 5-Speed, with 2.3 engine. My temp gauge hardly moves at all... It actually appears as if it doesn't move it you don't pay close attention and were to just glance at it. I'm thinking it is most likely the temp sensor that is on the engine block as I understand there is also one that is in the line that controls the fans for the radiator. Am I approaching this in the right direction or is there something else I might need to do?
View 3 RepliesI have a 2011 xlt extended cab with a 2.3l 4 cylinder. The truck is great... I put 120,000 miles on it in under a year.
But about a month ago the temperature gauge started malfunctioning. for what ever reason -- the truck is NOT over heating-- the gauge would increase past the "H" and then the temperature light would come on. Because the truck thinks it's overheating -- the engine goes into a "safe mode" and runs with no power. When i shut the motor off and turn it back on temperature gauge resets and the truck will run fine.
Then in another 50 or 100 miles it will do it again. Why is it doing this? I took it to the dealer here in Columbus, Ohio and the mechanic installed a new thermostat and a new "control modulator" (and a part -- not really sure what it is called) anyway, the truck is doing the same thing and the mechanic still does not know
I just picked up a 1984 ford ranger long box 2 wheel drive w/ 2.0 l and carburetor for our daughter whom is just 15. it has a whopping 19,000 actual on it! It was my wife's grandma's farm truck - ordered it new from dear born. Any way, fuel gauge is pegged at empty and they had a new float assy put in about 5 years ago, but it is dead now, it doesn't appear that this sender is avail any longer. What part might fit in there and or what do i have to do to maintain the original gauge in the cluster but have a working sender to talk to it? is there another unit that goes in the tank that i can modify the signal out to read right with the built in gauge? There can't be too many different ones out there is there?
View 8 RepliesNew owner of a used 2002 Ranger XLT 4x4 (with 59k miles) here (and new to this forum). Having problems with the oil pressure gauge not registering on cold starts (though it registers after the engine warms up).
I know this is nothing more than an idiot light since the gauge isn't really a gauge (inasmuch as it registers in the normal range at 7 psi and stays there unless the pressure goes away).
I've read that this is likely due to the oil pressure switch not functioning properly. I'd like to know where this switch is located on a 4.0 L V6. Other than this, the engine functions normally (though it sucks the gas).