I just got my grandpa's 2002 Ford Ranger Edge after waiting years to obtain it. It runs great the only problem is that there is NO power to the radio what so ever. The truck belonged to the family and every one drove it but no one knows what happened.. There is no power to Fuse 28 however 12V to all other fuses that have to deal with the radio.
View 12 RepliesI have a 96 Ranger . Neither my cigarette lighter or the auxiliary right beneath it works. The fuse checks good at the panel and I also used one of the penlight 12 volt testers and it shows no voltage on the lighter housing. Could there be another fuse under the hood that shares that circuit or do I have an open somewhere and need to tear down the dashboard? I haven't been inside that dashboard since I replace my cluster and the lighter worked after doing so. But I wish to avoid going back in there.
View 3 Replies02 Ranger with 3.0 Flex motor, 375K+ miles. Been chasing an issue for a while now, but am about at the end of my diagnosing capabilities. Issue started with a misfire on 5 and rough running engine with no codes showing up. Now the motor is getting worse.
Idle a little rough and no power when accelerating hard. The engine sounds like a popcorn popper under hard acceleration. Motor revs up to 4K but does not pull or shift gears until I let off the gas.
The code that initially showed up indicated a bad Camshaft Position Sensor. Changed that and the Sync assembly - as per instrucions, exactly positioned same as old one. New codes showed up - P1152, P0175, P0171. Cleaned the MAF, rail fuel pressure OK, can't find any vacuum leaks, replaced both upstream ox sensors, and changed #5 ,6 injectors.
Motor still runs the same - like crap, like a corn popper on acceleration, smooths out if only slightly accelerating, but stumbles n bumps on steady cruise speed over/around 60 mph - and no codes showing at present.
I really, really don't want, nor can I afford, to take it to the dealership, but I may be forced to if I can't figure this out sometime quite soon. I make my living with this truck so, no truck, no work till this issue is solved.
I have a 2002 ford ranger with the 2.3l and 5 speed.
Long story short, previous owner adjusted the time because he accidentally got the motor out of time (he thought it had the belt, not the chain). So he had to take the intake, fuel rails, fan, throttle body, etc. Off to get to the valve cover to re-time it with the timing kit. After it was put back together, it ran awful. I bought it, checked the time with the timing light and it was good. I replaced the spark plugs, and then realized he had forgotten to plug the camshaft positioning sensor back in. So I did, and that did the trick. From start to finish, the truck had those issues for about a year before I got it so it sat up for a little while. I have had it for 2 weeks now.
Now the problem...it idled great. But when I took it out for the test run, 1st gear shifted great, but at about 1700-2000 rpm (depending on the gear), it would almost seem to loose power, and then it would pick back up around 2400-2700 rpm like nothing had happened. You can sort of tell in 2Nd gear, but it is very noticeable in 3rd, 4th, and 5th. If i accelerate pretty slow, it doesn't happen. It only if i try to accelerate at a normal rate or if i am trying to get onto the interstate or pass someone. I ran some seafoam in it thinking maybe it just got gunked up from sitting for so long, but that only through an engine code saying my bank 3 was misfiring.
So I replaced the spark plugs (again), wires, and then the coil pack (the coil pack is what fixed it) and that got the code to go away and for it to stop missing, but the problem still was the same. It would take off great, and then it would seem to almost pause, and then pick power back up again. It wasnt feeling like it isn't getting enough fuel, it just wouldn't hardly pick up speed. It almost feels like I am riding a 2 stroke dirt bike. The power band is ehat should be normal on the truck, and before I hit the power band is how it feels when the truck has its little pausing episode. It's that noticeable to me.
So I thought maybe the fuel filter or sensors need cleaned/replaced..so yesterday I replaced the fuel filter and cleaned every sensor around the top of the engine, including the MAF sensor and made sure all bolts were tight and gaskets were good. I don't see and disconnected vacuum lines and none of them looked dry rotted. The only place air can get in that I see is the air filter box. The screws that hold the top half of the (stock) filter box are missing, so it is not sealed.
But what to check next. My only other thoughts are the catalytic converter (which it doesn't act like it's stopped up) or the fuel pump pressure being off. Also, it does sound like a lifter ticking in the motor, but previous owner said he thinks it did that before all these problems.
Also, right before I bought it, it sounded like the ujoint was squeaking (it rarely does it now) and now it has a crackling sound when accelerating at low-mid rpms coming from the middle or the back of the truck. It sounds similar to when you turn your hot vehicle off and the exhaust makes crackling noises sometimes.
Description: It will crank over forever but not start. New timing belt water pump, etc, so it is not timing. tried different fuel pump relay. no luck. new fuse no luck. The radio fuse also shorts and blows when I change it. Headlight does not come on, but the cabin "ding ding ding" sound plays. Marker, turning, reverse, and brake lights work.
CHECK ENGINE LIGHT does not come on during key turn. I may know what caused it or it may not. Before all of this happened, my audio system fuse under the hood blow. It blew again after I installed a new fuse (immediately).
One day, the wires on a portable cigarette light pump snapped and the two wires had been touch. I noticed the truck stalled several times when letting off the gas and coming to a rolling stop. The fuel pump relay makes a click noise when I turn the key
I have a 2002 Ranger with a 3.0/auto with about 180K on it. It runs good but for the past 6 months I have had a problem starting it. It does the same thing hot or cold but is a LITTLE easier when cold. It is very hard to start, you have to grind the started for about 30 seconds then it starts right up.
I checked to see if I could hear the fuel pump when the power is turned on and yes I can. But after checking the fuel pressure, there is no fuel pressure with the power on and the engine not running. Once the engine starts, there is about 65-68 pounds of fuel pressure - and the truck runs just fine. Starting is the only problem.
I was told I had to replace the fuel pump. Is the electric pump in the tank the ONLY fuel pump on the truck, or does it have a combination of the electric/tank pump and a mechanical pump on the engine?
2000 Model, The fuse keeps blowing on this. I thought it was the cruise control fuse because the cruise kept not working and when I replaced fuse it would work. Only for a little though, then I looked at manual and it says the fuse is for the brake position switch. I am presuming this is just like the old days and that is the brake light switch under the dash. They use to have two wires now there is like five. Anyways I do not see any bare wires or anything that would blow a fuse, is it common for these switches to go out or what??
View 13 RepliesMy dad's 1991 Ford ranger 3.0 2wd just died on him when he was driving home and I checked to see if the truck had a spark and it did not so I replaced the ignition control module, then ignition coil, then distributor and rotor cap(plug) and I put new plugs and wires on it a few months back too. I also checked to make sure that the timing chain was working as well (while I had the distributor cap off). Then I realized that the EEC maxi fuse was blown. I then found a fourm that said it might be the relay so I replaced the EEC and the fuel pump relays while I had them both out. Every time I put a new 30 amp fuse in the EEC slot and turn the key to start it the fuse blows and the truck won't start. What might be wrong?
View 1 RepliesFuse #41 keeps blowing...scan tool says o2 sensor heater circuit malfunction. Problem is that when the o2 sensors are unplugged it keeps blowing fuse the second I hit the key. Where this short would be? I can't find a wiring diagram anywhere. ( I'm new to this forum and I'm sure there is a sticky somewhere..
DTC codes: P1451, P0743. P0750. P0760. P0765. P1747. P0135. P1409. P0755. P0155
I've a 1994 Ranger XLT 4.0L with a missing fuse panel cover. I'm trying to get the horn to work and we've traced the problem to a missing fuse. Unfortunately, there are 3 empty fuse slots and no info on their rating or use. Where I can get the proper info. Truck was a salvage, no ops manuals, and sloppy work putting it together.
View 14 RepliesSince last summer my truck keeps blowing fuse 26 and then I have no reverse lights. If I replace the fust its ok for a bit but blows again the same day sometime. The book says its the fuse for revers and overdrive. The overdrive button on the tree shifter stops working too but the truck does not seem to be revving any higher so I think the overdrive itself is fine. I can't find the short but its got to be shorting somewhere...
View 14 RepliesI recently got a ranger from my buddy and it keeps blowing the EEC fuse in the engine compartment. We have replaced the EEC relay and the EEC power relay. As soon as you turn the key it is blowing the fuse.
View 1 RepliesMy 1996 Ford Ranger's Fuel Pump- Fuse keeps on blowing... (Fuel pump is new)... We need to find where the short is coming from!
View 2 RepliesI've got an 86 ranger sport and I'm having trouble with the lights. The turn signals work, and ALL 4 bulbs in the back are new. The brake light fuse keeps blowing, and the fuse for the tail lights is good but they won't come on at all. I was told there was a direct short somewhere, does that sound about right? And is there a common place where they tend to short out?
View 2 Repliesfuse #11 in the battery junction box under hood keeps blowing, the last time I put a fuse in it blew immediately, key was off and lights off. Fuse is for parking lights, dash light and I/P(whatever that is) and switch illumination lights. I have to start following all wires to find bad spot. May just put in piece of metal and watch for smoke...
View 3 RepliesSo I did alot of electrical work on this truck but never had any problems with the brake lights, now they dont work and the fuse blows every time you pop one in.
View 1 RepliesI have a 2011 ford ranger XL and I get no high beams. My low beams work fine but when I try to either activate the high beams or pull for the flash to pass they do not illuminate and the indicator on the dash doesn't come up either. I have replaced the fuse with a fresh one, even though it didn't need to be replaced, and also replaced the headlights as well cause one was burnt out.
View 1 RepliesI drove my truck 2 times the day it stopped running. The 3rd time I tried to leave it started moved about 2 ft, spit and sputtered and died. It had blown the fuel pump fuse. I changed it and checked the fuel shut -off in the cab, passenger side. It was not tripped. Tried to start it and as soon as I turned the key it blew the fuse again. I changed the fuse again and this time I changed the fuel relay and the switch in the cab. Turned the key and it blew the fuse right away. Went to AutoZone because they are close to the house described what it was doing to them and they said sounds like a short in the fuel pump.
I purchased a new pump put it in turned key blew the fuse, pump just clicked...I found this site and my son noticed a thread where it said wires under the cab are good for wearing through and grounding out. I looked and it did wear through one wire coating. We taped it up, put extra cover over it and now it does not blow any fuses. Fuel pump still just clicked. Took fuel pump back for an exchange.....same thing. Turns over but fuel pump will not pump fuel. What am I missing?......
Our Ranger, 2002, 4 cyl. 2.3 5 speed is shutting down while driving. This has happened twice very recently. Both times on interstate at highway speed. First it loses power then completely shuts down. After stopping, turning key "off" it restarts and runs fine. It does take a longer time to crank before starting.
It is not throwing any codes and the CE is not coming on. I suspect the fuel pump is shutting down. Seems like fuel pressure loss is reason for loss of power? Then extended cranking to restart is the initial build up? What else could it be? If not the pump itself, is there something that would take away power from the pump then get reset?
I am installing a used tranny in the ranger. According to the salvage yard the tranny fluid and filter was removed and fluid drained from the torque converter. How am I supposed to fill the torque converter?
View 1 RepliesI have a 02 ranger..3.0 standard trans 4x4.... Started running crappy, cleared up and when shut off, now wont start... Good spark and good gas pressure... Seems to want to try, but just doesn't go. No codes or pending codes.
View 8 Replies