Ford Ranger / B-Series :: New Heater Core / Blower Motor And Resistor Still No Heat?
Sep 22, 2013
with a new heater core, new blower motor, and new resistor and no heat, what would be the problem? gonna check the thermostat tomorrow.
View 2 Replies
Sep 22, 2013
Advertisement
Ford Ranger / B-Series :: 1997 - Heater Blower Motor Resistor Rusted
I am not great with electrical but can manage. Here's the deal, Ihave a 1997 ford ranger 2wd 2.3L 5spd with a/c 233,000 miles i just replaced the heater blower motor resistor as the old one was rusted bad as was the pig tail going to it bad that one of the terminals broke off and was rusted in the harness so i replaced the plug as well problem is i still have no fan if i jump it it works but have no power at the plug for resistor or motor and no power at the switch inside the truck I do have power to one terminal where the relay plugs in, where to look next?
View 14 RepliesFord F-150 - 1997-2003 :: Blower Motor Resistor Location
I'm looking for information and possible photo location for the blower motor resistor. My truck has climate control. I've looked under the dash on the passenger side and behind the glove box door and I've been unable to spot the location. Do I have to remove the plastic panel behind the glove box?
View 6 RepliesFord F-150 (2009-2014) :: Blower Motor Resistor Overheating
Have a 2009 platinum, 5.4, supercrew with dualzone heating and air. The blower motor resistor block is overheating and melting the connector block. fooled with it way too much, and then put a new resistor and pigtail in it. The new resistor would kick out in about 30 seconds, so used the old resistor on the new pigtail, got hot, melted the new pigtail. What is causing the resistor block to get so hot, and what do I do about it?
View 7 RepliesFord A/C :: After Changing Resistor Blower Motor Started Smoking?
I parked my 2003 f150 about 8wks ago, and at that time the blower had been running only on high then not at all, then only on high again.
As I need it to pull the boat up north next week, I purchased and changed the resistor. When I started it up the blower motor wouldn't run and eventually it started to smoke, so I pulled the wire connector to the motor.
Where I can find a procedure for motor testing, and removal as I think this is probably where I'm headed with this. There seems to be utube videos on everything else but not this. I may just have to go out and purchase a Hains or Chilton manual but I'm Scottish and always look for the free route first.
Ford Ranger / B-Series :: 1996 - Heater / AC Blower Only Works When Warm Out
I have a 1996 Ranger that the Heater/AC blower only works when the outside air temp is above 45 degrees. I have replaced the relay, and the blower motor resistor. What could be causing this?
View 3 RepliesFord Ranger / B-Series :: 1997 - Blower Motor Doesn't Work
I've got a new to me 97 Ranger that the blower has never worked in and I can't get it going. I've checked the fuse. That's good. Tested the relay. That's good. Did an ohm test on the power switch for the blower. It's open in the "OFF" position and closed in the other positions. I've got continuity through the speed selector switch. New resistor and pigtail because the other one was nasty looking. What seems odd to me is that I've only got power to the blower motor relay at one terminal with the switch on (number 30 I believe). In addition, when I test the plug for the motor itself with my test light, one of the wires (org/blk I think) has power only when the switch is off. And I ran power straight to the fan from the battery and it spun right up. What am I missing?
View 8 RepliesFord Escape / Hybrid :: 2005 - Location Of Blower Motor Resistor
Where the blower motor resistor is located on the '05 model.
View 11 RepliesFord A/C :: 2006 F350 - Location Of Blower Motor Speed Resistor?
I have google it looked all over was told it was under the hood next to the fan even shown a photo when I went under the hood right were the resistor was in the photo there was a long black box about 4 inches long and 2 inches wide. looked nothing like the photo.
So I went back on line and read that its above the passengers feet you take a few screws off after you take the glove box off and it should be there. Well after taking 8 screws off I find nothing but a coil behind there. Nothing that looked like a resistor.
2006 f350 diesel?
Ford Ranger / B-Series :: 1985 - Heater Blower Sounds Like A Legion Of Demons
When I turn on my heater full blast the most god awful squealing commences. Where to start spraying the grease?
View 10 RepliesFord Ranger / B-Series :: Fan Only Work At High Speed / Blower Motor Hose?
I recently bought a 96 ranger.I noticed the fan did not work but for high. I search the internet and found how to remove it and discovered a mouse nest(village) which basically took over the housing where the evaportor core,blower motor resides. I bought a chilton but cannot remove the housing around the core so I cleaned it the best I could(air compressor and vacuum and disinfectant)...
I had to buy a new blower motor and resistor. However, I cannot find the hose that attached to the blower motor?-mouse had chewed a hole in the one- I've looked and found serveral differents names for it but seems I cannot find it at my local parts store.
My question is- is this intake hose? vent hose? I'm guessing I will have to go to dealer or, if I know the name I can look it up in a salvage yard?
Tiguan :: Blower Motor Resistor Location
Where blower resistor is located?
View 6 RepliesAlero :: 2000 - Blower Motor Resistor Replaced
2000 Alero. Wife reported to me she had no blower motor. I pulled the motor and it tested good. Next I replaced the resistor with one from auto zone. Now I have blower in all but the 5th and highest position. I suspect a bad new resistor but I left it for now because it's a pain to remove.
Could I have got a bad resistor? In my experience a bad resistor will give you high and nothing else.
Ford F-150 (2009-2014) :: Blower Motor Resistor Replaced - Fan Completely Shuts Down On High Speed
I replaced the blower motor resistor on a 2010 F150 with dual climate control where the blower was stuck on high.
After replacing the resistor, now the lower speeds work fine, but when placed on high speed, the fan completely shuts down. Replace with the old resistor, and it only runs on high.
How to proceed, or what else might be the problem?
Grand Prix :: Are Resistor And Blower Motor Close Enough To Cause Leakage?
I have a 2004 pontiac grand prix gt. I read some where that some of these have the resistor and blower motor close together and that the molding or rubber that runs at the bottom of the windshield after time will leak water into the blower motor and resistor and cause a short. I believe this has been the cause of a lot of my issues with car shorting out. the other day had to have it towed for the first time in its 11 years and found out it was one of the j fuses arcing causing the car not to start.
It's already 267,000 miles.
Ford A/C :: Replaced Front Heater Core Now No Heat In Rear
2000 Expedition. Had ford mechanic replace front heater core due to not having heat in the front and back. wife brings it home I check all vents and notice there's good heat up front but not the back, then I switch the rear from panel to floor heat and hear a thumping sound (figure the blend door is doing it) still no heat in rear. returned to ford mechanic and they stated my blender door switch is not working properly, so they flushed out rear core and instead of fixing the blender door switch they kept it on floor position and charged me another bill. could it be possible that while replacing front core the gunk made it to the rear hoses and core, and clogged it up, and damaged the blender door switch somehow. prior to my heat issues I never had any problems with the rear blender door, just no heat due to front core needing replaced according to them "FORD".
View 1 RepliesFord A/C :: 1994 - Replaced Thermostat / Heater Core And Water Pump Still No Heat?
the only thing that is left to replace would be the radiator?my truck is a 1994 f150 and it is not overheating!i get lukewarm heat only on the highway,everywhere else it is cold air!!this new england weather is killing me
View 10 RepliesFord F-150 - 1997-2003 :: 2000 - Low Heat Output / Heater Core Clogging Up
I cant find my original post but I am reporting back on a low heat output issue. Not the climate door. It was the heater core clogging up. Instead of replacing, this is what I did. Purchased a "drill pump" and some clear hose and some CLR. Cut both the heater hoses,taking consideration of where best to install "T" connectors.
While hoses disconnected,filled heater core with CLR(as much as I could get in it). Hooked clear hose,drill pump configuration,on to the heater hoses. Ran drill pump in both directions for several minutes and stopping and letting it sit for a few minutes.
About 1 hour all together. Pieces of debris came out of the heater core and I could see it through the clear hose. Flushed the heater core out. Installed "T" connectors and it is heating very well now.
Gmc :: No Heat In Van - Blocked Heater Core?
I have a 2010 GMC 3500 Savanah van with 6.0 motor. No heat in van. Engine operating temp is normal. Heater hose into core is hot. Hose coming out is barely warm. I am of course hoping for another explanation other then blocked heater core. The truck only has 45k miles. I am ready to backflush , but wondering if there can be any other explanation. A/C works normal.
View 1 RepliesFord - Explorer :: 2004 - No Heat / Not Getting Vacuum To Call For Coolant To Enter Heater Core
I bought a 04 explorer with a bad thermostat which led to a bad head gasket, fixed that and managed to not have to buy the special tools or time it , but now that its running I don't have any heat. I have complete service records on this vehicle and there was never a complaint of the heater not working. The a/c works and the heat will adjust the a/c temp, but no heat. In trouble shooting it I found that I am not getting vacuum to call for the coolant to enter the heater core. When I apply suction to it, it will send the coolant. Even though I wasn't getting the clicking noise, I pulled the blend door actuator and it looks surprisingly good (not looking forward to putting it back in). Where to look next?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Replaced Injector Cups - Too Much Heat From Heater Core?
I just finished the replacement of my injector cups and I replaced every hose on that engine and when i replaced the heater hoses I believe I hooked them up right but just want to make sure. Is there an IN and and OUT on the heater core or does it not matter???? Im only asking simply because my legs feel like their on fire. Im wondering if the hot coolant is flowing through with out demanding it. I havent drove the truck in a while so Im questioning everything.
View 2 Replies