I have a 2001 f250 7.3 4x4 today I locked the hubs, put it in 4 low and got threw some mud to go hunting fine. got back out of the woods and took it out of 4x4 unlocked hubs and went in reverse 30 yards.. Now when i drive it makes a weird sound like a rubbing sound near the front axle. What this is?
View 5 RepliesI have a '01 F250 with a frozen u-joint in the driver side front axle. My question is can I put it together without the axle and drive it?
View 2 RepliesCheck out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 RepliesFinally finishing up my 2001 F250SD 4X4 project. Decided to pull down the front axle to replace the dust seals. I've got everything apart including the large knuckle seals. Tried to pull the passenger side axle out but it only moves about an inch to an inch and a half before it stops. Took off the differential cover to look for damage or something obvious but I don't see anything wrong. The axle is moving within the splines of the spider gear but that's it. Stumped and sitting on jacks!
View 14 RepliesI noticed my '12 F250 has grease zerks on the front axle u-joints and was wondering how often you need to grease them ? My truck has 10k on it and while I was changing the oil tonight I decided to give them a few shots of grease until it started coming out of the joint.
View 12 RepliesI own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 RepliesI noticed yesterday that my tire on the driver's side has rubbed a flat spot on the rubber brake hose. I bent the metal tubing so that it doesn't rub any more, but should this be of great concern? Obviously I'd hate for it to rupture, but it looks as though it's not too bad.
View 1 RepliesMy 2013 f-250 with 6500mi. has peeling paint on the front differential and the axle.. I sprayed it with some fluid film for now.
View 14 RepliesI broke 2 snap ring plier on this thing, what is the make and model of snap ring pliers used to remove the snap ring off axle in hub ? I have some others but too beefy won't move in there. They need to be long but strong. I've heard Snap On Item: SRPC9000A works but I don't know of any Snap On guys around here and I need to get this thing done.
View 10 RepliesI just put some toyo at2 295.75.16. On my 04 250. And I've got some rubbing on the plastic and front leaf springs. If a 2.5 " spring left will take care of the rubbing or will I need wheel spacers.
View 3 RepliesI bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 RepliesI got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 RepliesWe were using my 2001 7.3 4x4 (automatic, manual lock outs) in 4 low yesterday on dry pavement in an attempt to pull out the remainder of a 6x6 post in concrete. We were working her pretty hard alternating directions of pulling. At one point we heard a loud bang (see also: thud; pop; etc). It seemed at that point that the front axle was no longer functioning in 4wd. We still had the low gearing feel, but at one point I noticed my rear tires trying to slip on the driveway, but fronts didn't appear to be pulling anymore.
Long story short, came in, went to bed, went out this morning and thought I'd jack up the front end and roll the tires in both 'free' and 'lock' to see if the universal joints (yokes?) behind each wheel were spinning or not, depending on whether free or locked in. I noticed on the passenger side a few drops of a clear/light colored fluid that had dripped from behind the dust cover that isn't functioning any longer. The joints worked as they should, based on if it was locked in or not.
I decided to go ahead and put the back axle on jackstands as well and see how it was working when "driving". When in 2wd, rear worked, front was stationary, as it should be. when in 4high, rear spun, front driver spun erratically, nothing from passenger front (where I had seen drip). 4low was same thing - erratic on driver side, at best.
So I know I have front axle/transfer case issues. The question is, with the drip (smells like grease, so I'm assuming its gear oil?) would I be safe to drive it a few days with hubs in free position? I don't want all of the fluid leaking out when I'm driving down the road. I use the truck for work and wouldn't be able to be without it until later in the week or next week. But I also don't want to drive it if it will just make my predicament worse.
I have a really loud whining kind of noise found that its the wheel seal rubbing on the inner part of the wheel bearing. I was just curious if its safe to drive with the spindle removed from the axle?
View 5 RepliesI have a 2001 f250 4x4 about 4 months ago I replaced my pass. side front wheel bearing unit and here recently about 3 to 4 weeks ago I get a grinding/ rubbing sound when ever I turn right it gets louder the harder the right turn I do not seem to notice it as much moving at speed but driving through parking lots and slow speed right turns I can hear it. I have checked everything and nothing is loose and I can not see any signs or fresh rub marks on anything. I am getting to the point of just buying a new unit and replacing the one I just replaced. What my problem could be?
View 3 RepliesI have a 2011 6.7L F-250 with the stock 17" rims and need new tires. Would 285/75/17's will fit without modification or rubbing?
The stock tires were 265/70/17 and were too small. I have 285/65/18's on there now without rubbing, but it is close. Going back to the 17" rim with a taller tire makes me a little nervous, as I can't check them before purchasing.
I do not want to have any rubbing or have to do any modifications (lift, spacers, etc...). I would like to keep the vehicle stock.
My 11 cc lb 4x4 6.2 has a clunking/loose sound coming from the front end. It is prominent when going over small/medium bumps but not so much large bumps. I have had my local dealer and a couple local shops look at it and they all say everything checks out. It definitely seems like something is loose in the front suspension. I just put new Gabriel max control shocks on all four corners. I have no play in wheel bearings or ball joints. Tie rod ends also look fine.
View 12 RepliesI have a 1999 F-250 super duty 7.3 4x4 and the rear drivers side axle seal is leaking. My question is how do I remove the axle shaft? my last truck a f150 had c clips in the diff that released the axle shaft but I did not see those on this truck. How to remove the axle shaft?
View 8 RepliesLove my '11 f250 SD 4WD CC SB. 6.2 with 3.73 e-locker. I've got 5 Star tunes in it, and the truck is a joy to drive empty, and tows my current 7k camper fine, though on steep inclines I wish I had the 4:30 gears.
Well, we just bought a bigger trailer, dry weight is an addtl 2400+ at 9400, so I'll need to do something.
I don't want a different truck, don't want (another trouble-prone) diesel. I think with 4:30s and the tune, I should be fine towing that trailer (with gear and passengers, probably 11-11.5k loaded). Not doing mountains here, just Michigan hills.
What's the best way to "do" a gear swap? I know if I buy a set of gears and a shop screws Em up, it's gonna whine/hum and still cost 2k to do (truck is 4wd)
I'm up in the boonies and finding a shop to swap the gears will be a problem. Getting Em done right will be even MORE trouble.
Can I just find 4:30 axles ans have them swapped (anything in t-case or sensors need to be touched?). I don't care if I lose the e-locker, I never use it.
I have a 2001 Ford F-250 with the gas v-10. Yesterday it started just fine as always. Today I get into it and it starts to turn over just fine then starts to make a grinding sound and the truck won't start. I have had a fuel issue in the mornings with once it started you had to barely press the gass to keep it running. But never makes a funny sound and always runs fine. This only last for a couple of min and then it runs fine for the rest of the day. The grinding is not the starter. I took it off and had it checked and it was fine.
The truck had been using oil. When I checked the oil level it was low but it was still on the stick. "I know a motor needs oil to run smooth but it's my dads truck and well let's just say he is not the best on maintenance". Also I smelled the oil and it does have a gas smell to it. So it definitely does have some gas in the oil. I tried to light the dipstick with a lighter and it wouldn't light. So not sure how much gas is in it but that's what I did.
So the question is, would something just in mid crank go bad and then not let the motor crank. Truck made no weird noises before this so I find it hard to believe the barrings just went out in mid crank and now it is shot.
Also I just checked compression on front cylinders.
Driver side read 75lbs
passenger side read 100lbs
Here's the deal. I have a 2001 F250 4x4 and I am getting a noise in the front drivers side wheel. The noise is not a grind or clunk, but its like a u-joint is rubbing inside an empty cylinder kind of. Anyways, it seems like it does it only with small bumps. I took off my oem hubs and re-installed them and the noise went away for about a week. Now I replaced them with manual locking hubs and the noise is back. One other thing I notice is if i put the switch to 4x4 the noise goes away. I checked all major components for the steering and suspension and nothing was loose. The front end is tight. Is there anything inside the axle that would cause this? I dont know what to check for anymore. Where else to check?
View 4 Replies