Ford Super Duty (1999-2016) :: 2003 F250 - Front Tires Leaf Springs Rubbing Even On Slight Tight Turn
Jun 8, 2014
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 Replies
Advertisement
I just put some toyo at2 295.75.16. On my 04 250. And I've got some rubbing on the plastic and front leaf springs. If a 2.5 " spring left will take care of the rubbing or will I need wheel spacers.
View 3 Replies
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
View 10 Replies
This is my dads f250 build date of 9/03. I know these wheels are not the factory xl wheels. I also think they changed something with the wheel back spacing somewhere around this time. He is running 285/70/17 bfgs and is rubbing the leaf springs pretty good. He ran this same size on his previous 02 model with no rubbing. Can he get away with 1/4 spacers? What years these wheels are from? And the backspacing differences, if any. His 02 had the chrome large bullet hole style wheels.
View 5 Replies
I have a 99 SD 250 diesel, I also have a broken rear leaf spring. My truck has a 3 1/2 in. block between axle and leaf. My question is this. Can I remove the block and install 4" lift leaf springs without messing up my pinion angle? The blocks look square. But someone toldme once they are made to a specific angle for rotating pinion for better u joint alignment. Sounds like it could be true.
View 9 Replies
I have a 2000 F350 that was once a work horse. Its now just my daily. The leaf springs in the rear have 2 broken on each on and the front need to be replaced due to 344K miles on them too. My question is how do I soften up my ride on leaf springs though? Theres a local shop that will do the work, but my rears have 7 leafs / front 2. It used to tow daily but I dont tow anything with it. could I go to 5 in the rear to soften it?
View 14 Replies
I noticed yesterday that my tire on the driver's side has rubbed a flat spot on the rubber brake hose. I bent the metal tubing so that it doesn't rub any more, but should this be of great concern? Obviously I'd hate for it to rupture, but it looks as though it's not too bad.
View 1 Replies
I decided to go ahead and do a rear block replacement. I'm going to install the Ready lift 4 inch blocks.
I have both u bolts and nuts off of both sides. Rear stabilizer bar disconnected and both shocks disconnected. However, when I raise the rear of the truck, the axle raises as well. What could be holding it on still? I noticed there's a nut in the middle of the leaf springs. Do I take that nut off? I just don't know what could be keeping it from separating.
View 11 Replies
We have a lot of snow and a lot of ice up here at the moment and my 2003 ford F-250 SC Fx4 isn't performing so well. The truck is stock other than a pair of 285/16R BFG A/T's
I have been noticing that my rear tires will spin while trying to go up hill on some ice or snow covered areas and my front tires just sit still while in 4x4 or 4x4 low. In the case I just described I remain stuck in place until the rear tires can get a grip then I continue up hill. I don't understand why my front tires are not spinning as well, to me this seems just like 2 wheel drive not 4x4. I have been using ESOF most of the time. I have mentioned in other threads that I do plan on upgrading to warn premium hubs, but I am wondering if its that my truck isnt actually shifting into 4x4 or if there is a reason why even in 4x4 my rear tires would spin while my front tires do not?
I am confused because when I shift on the fly while driving I can feel the 4x4 kick in because it just feels different than driving with 2 wheel drive, but then something like I described will happen and I start second guessing myself. What might be happening? It's not that I am opposed to switching to the warn premium hubs, but is that actually going to fix this issue or is my truck acting normally??
View 13 Replies
I just bought a used 2013 F-250 4x4 and it came with the snow plow pkg. heavy duty front springs. I love the truck, but won't be plowing with it, and I don't need the rough ride (and don't like the look of the front end higher than the rear)
How hard is it to swap out the front coil springs and replace them with the "regular" ones?
View 7 Replies
Have a problem When i make a slight turn to the left sounds like the tire is rubbing the inner fender. Don't do it all the time. The tire is not rubbing.
View 4 Replies
I got a f250 4x4 1999 super duty , I have 20" 10'rims , can I run a 35" 12.5 x 20" tires without rubbing
View 1 Replies
I tried to replace the rear spring bushing of the drivers side front leaf spring.
Got the nutz off the shackle... The lower bolt was bumping into the front drive shaft and would not come out all the way.
Biggest problem I was having seemed to be I could not get the axle to drop far enough to release the pressure on the bolts in the shackle.
NOTE: I was trying to do this without unbolting the U-Bolts from the axle.
I was under the impression you could do this without unbolting the u-bolts. I have all new hyperflex suspension bushings and would like to get them on.
View 11 Replies
I have a 2001 f250 7.3 4x4 today I locked the hubs, put it in 4 low and got threw some mud to go hunting fine. got back out of the woods and took it out of 4x4 unlocked hubs and went in reverse 30 yards.. Now when i drive it makes a weird sound like a rubbing sound near the front axle. What this is?
View 5 Replies
I had my leveling kit installed today. Bilstein 2" leveling coils, adjustable track bar, 4" rear blocks, and shocks front and rear.
I have 295/70/18 tires on stock wheels that didn't rub anywhere before. Now at full lock to the left the drivers side tire just barely rubs on the radius arm. How is that possible? I was planning on getting 35s soon when these wear out but it seems like those would rub even worse.
View 8 Replies
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
View 8 Replies
I'm looking at a 2004 F250 XLT super cab 4x4 with a 5.4L with only 50k on the clock. It looks to be in great shape and drives good with only a few issues. Cruise doesn't work, it pulls to the left a little, and it has a slight roar coming from the left front wheel. Other than that it seems to be a nice truck. Its blue and grey two tone. Anything else I need to look at before pulling the handle on this one?
View 11 Replies
I've got an 04 f250 4x4 crew cab. I just replaced the upper and lower ball joints on both sides and also the drag link. My alignment was off from the bad ball joints so I had it aligned after I did all of this. Now the steering is really weird. Its like something is to tight. I can barely keep the truck straight because every time I barely move the wheel I seem to be going one way or another and getting it straight is nearly impossible to the point I look like a drunk driver. I can turn the wheel to go around a curve and let go of it and it will stay that way until I turn it back. It won't return itself. I'm kind of lost.
View 3 Replies
I just realized my driver's side front leaf spring on my 2002 F250 has snapped. I checked the weight sticker on my truck and it weighs 5200lbs in the front. My question is the heaviest springs I found only support 2630lbs a piece, so being a 7.3 is 5200lbs a correct weight for the front of this truck? also why would Ford make springs that support only 60lbs more than the front weight? Hell I weight more than 60lbs.... Did I snap the damn thing just by climbing into the cab?!?!
View 6 Replies
My front passenger leaf spring just broke on my 2000 f-350. My front springs are T code, but I was wondering if a could replace the broken one with a code X spring as a temp fix until I get a leaf spring replacement delivered?
View 1 Replies
What is the width between the spring perches on leaf sprung 99-04 front axle. I searched and cant seem to find a dimension listed anywhere. i tried the dana60 bible on the pirate site as well, but it doesn't list the spring perch dimensions, only for the pre 99 styles
View 2 Replies
