Ford Super Duty (1999-2016) :: 2002 F250 - Front End Noise / Slight Vibration In The Floor
Dec 10, 2010
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
View 8 Replies
Advertisement
I have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 Replies
I am new to the Superduty and the Diesel world. I just purchased a used 2006 F250 SD XLT with 79K miles on it. This truck has a brand new 6 inch rancho lift. I just bought brand new 35x12.50x18 toyo open country AT tires and new 18 inch rims. I have the steering box replaced, new brakes all the way around, front end alignment and the Turbo pedestal secured.
However, I am still getting a vibration in the floor going down the highway when i hit 70MPH under acceleration? Once I let off the gas the noise goes away.
View 4 Replies
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
View 11 Replies
I have a 2002 F-250 7.3. I was driving home from work on Tuesday (highway), I heard an intermittent noise coming from the front end, sounded like a rubbing/grinding noise. Yesterday on my way to wok, same thing, on and off. Yesterday on my way home the noise was constant, didn't go away. The noise comes at about 45mph and stays until I'm back under about 45mph, so mainly just on the highway. I put the truck in neutral and let off the pedal and the noise is still there which tells me it isn't engine related.
Yesterday after work I jacked up the front end, spun the tires, no noise. No play in the tires top/bottom or side/side. Took the tires off and what I did notice is the right axle u-joint is shot. I am hearing the noise in 2wd so I don't know if its the u-joint that's making the noise. Could it be a bad wheel hub bearing? Is it the u-joint? Maybe needle bearing??
View 6 Replies
The other day I got in my truck and started down the driveway when I realized I had no brakes, I slowly backed up and parked it. I haven't driven the truck for approx. 2 weeks and it seemed fine then. The master cylinder is full, there are no signs of leakage from wheel cylinders or lines. Today I unscrewed the left front zert and no fluid came out. My pedal goes all the way to the floor.... Whats going on, and if its a easy fix?
View 14 Replies
Today I was going to launch my new boat and when I backed down the ramp, the brake went to the floor almost sinking the truck. Long story short, the brake line that runs along the frame to the rear brakes rusted through at a bend that I couldn't see. Seems the line is about 8 feet long. What I'd like to know is can I replace it without dropping the fuel tank which of course I just filled yesterday and can I obtain one at a ford dealer or will I have to order one. My truck is my only transportation.
View 1 Replies
The truck is in my Sig 01 F250 5.4
Just got back from a long trip with it. Parked it for 3 days, all was running fine. Went to dinner Sat night and all was great, left the restaurant and as soon as I started the engine I noticed a slight vibration. As soon as I hit 42 miles per hour, it started shaking pretty good. I pulled over and checked under the truck to make sure I did not have anything I was not supposed to hanging down.
Driveshaft looked good, nothing leaking from rear end or tranny. When it does vibrate, the Tach shows the unhappiness as well. This a.m. driving to work it was vibrating at all speeds and shifting was very rough, had a hard time deciding if it wanted to be in second or third gear. I don't think this is drive train issue... When it shutters and sputters at 40ish MPH, its almost like it loses power and I have to let off the gas. and then under power it shakes badly.
I had the super chip settings for performance tow when this started and then I changed it back to stock settings, thinking it might work, which it only got worse. Changing the settings with the Superchip you have to disable the fuel system and I do this by pulling the fuel pump fuse under the hood in the power distro box.
I think the ujoints are still good, the oil and tranny fluid are spot on. Hubs are locked but in 2WD. Had all the front end replaced 15K miles ago. Brand new tires and wheels in Sept, front end alignment done at same time, front brakes were 90% and rear brakes at 20%.
View 10 Replies
I have a 2002 F250 with 189,000 miles. Im having some very bad issues that im trying to fix. The truck idles rough, with fluctuating RPM's. In certain speed reanges it also shakes and runs rough. If I turn the overdrive off the shaking pretty much stops, but it still accelerates pretty slowly. There is also a whistling noise from the front of the truck until the engine warms up, someone told me it sounds like a bad intake manifold? Does that sound right? What could be going on with my truck? All spark plugs and coil packs have been replaced, as well as the fuel injector rails.
View 2 Replies
2002 F-250 7.3 4x4 ...
I have a rattling noise coming from the front suspension (both sides) when going over small bumps. Most people point to ball joints, but I find my case odd because I just replaced
Upper/Lower ball joints
Track bar
Tie rod ends
Shocks
Front U joints
Drag link
I did not touch the leaf springs or the sway bar, except to grease the links, which otherwise looked good.
View 3 Replies
So, I'm slowly but surely eliminating a terribly shaky front end on my 2002 F-250 7.3L 4x4. First was a new carrier joint on the front drive shaft. Didn't work much, but the shop said the darn thing was falling apart. Next thing I did was new wheel bearings and manual hubs. Less vibration for sure. But the last remaining issue, in terms of vibration, is that when I let go of the Accelerator going at any speed above 60 MPH, it makes a horrible horrible noise, and I could feel a vibration. It shakes the whole truck, but I can very noticeably feel it directly in the gas pedal. It's really only an issue during deceleration. What could it be??? Drive shaft U-joints? Torque Converter? Something else in the Front End? Something in the engine even?? I don't exactly have the funds to tackle every possible solution.
View 1 Replies
I'm looking at a 2004 F250 XLT super cab 4x4 with a 5.4L with only 50k on the clock. It looks to be in great shape and drives good with only a few issues. Cruise doesn't work, it pulls to the left a little, and it has a slight roar coming from the left front wheel. Other than that it seems to be a nice truck. Its blue and grey two tone. Anything else I need to look at before pulling the handle on this one?
View 11 Replies
I have a bad wobble/vibration coming from front end i think i replaced hub locking hubs u joints truck dont feel safe at all took it to ford they say its normal no way its not just starting doing it few month feels like the 4x4 is in use when hitting bumps when driving if you go slight left or right it seems too make act up more.
View 2 Replies
I have a 02' 250 4x4 with 250000 miles on it. While driving between 55 to 65 mph there is a roar and vibration that seems to be coming from the rear. I have about 35% tire tread left and have had the rear tires balanced and it still does it. Having issues with drive shafts unbalanced or rear ends?? I am not sure where to start....
View 1 Replies
Ive got a 2002 f250 Sd 4x4 with 93000. Im getting severe vibration from the front drivers side at highway speed. I thought it might be a warped rotor but i cant feel it in the brake pedal, when I put the brakes on. How can you tell when the hub bearing assembly is going bad? The truck doesnt pull to that side either. I can hear it, and feel it more when i'm going around highway corners. When im driving through town, I can hear a "clunk,clunk,clunk" noise coming from that side also.
View 14 Replies
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 Replies
I've got a 02 SD v10 4x4 with Warn hubs and 97k. Bought it a couple months ago and I've noticed a vibration coming from the front driver side. Symptoms are that of a bad wheel bearing; vibration that increases with speed and not RPM, seems to lessen on left handed turns (weight transfers from driver side to passenger side) and gets worse on right turns. Also the truck seems very twitchy and hard to keep straight on the highway.
Snowed the other day so I locked in my warns (just in case) and I instantly noticed the noise and vibration almost went away entirely except for on the freeway around 70+ mph. Also noticed it seems less "Twitchy" on the freeway. Mind you the hubs are locked in but still in 2wd. After doing a little bit of reading some were saying this is a sign of bad needle bearings and not the entire hub.
I haven't jacked up the tire and checked typical movement in a bad wheel bearing. I know my way around vehicles and 4x4's pretty well...
View 3 Replies
I recently purchased a 2002 F250 Regular cab long bed 2wd. I'm tired of the front end sagging so low, so I've been looking into a leveling kit. I was wondering whether I should go with 2" or 1.5" for the kit. I tow about 2000 lbs. 3-4 days a week and do not want the truck to look like it is squatting too badly. However, I really would like it too look more level.
View 8 Replies
I've been chasing a noise/vibration that periodically comes from the front end of my '99 F250 SD. Quick & dirty of it........basically while cruising 55-60 down the road, sometimes when I hit a bump in the road or go over some railroad tracks or something like that I will get a grinding/vibration from what sounds like the front drivers side wheel. Best way to describe it is it literally sounds like my wheel is running on the rumble strip on the edge of the road at road speed. It will fade in & out a little & last maybe 5-20 seconds & eventually quite until some time farther down the road if I hit another bump. Doesn't happen all the time, just randomly.
So far to try & problem solve I have lifted the front & spun & kicked & wiggled & pulled on the wheel to see if I can feel or hear anything & everything seems solid. I have pulled the wheel off & looked the whole hub & wheel bearing over & everything seems fine. I have even pulled the 4x4 lockout out & inspected everything in the lockout & inside the wheel bearing & can't find anything that seems to be bad. (My original thought was that the Warn hubs I have might be messed up & the hub is trying to engage while driving down the road & that is the grinding & vibration I'm feeling.).
As mentioned above I have Warn manual hubs, I just replaced the wheel bearing last summer (only have about 10,000 miles on it), & all the seals & ball joints were done about 3 years ago.
View 11 Replies
My 2002 F250 is knocking loose the front end assembly--the gasket is worn out. So I was shopping around and was considering a beefed-up front end assembly.
View 3 Replies
I am in the process of replacing the front hub seals so my ESOF works again. I tested both front hubs with a mityvac and neither one of them holds any vacuum at all. All the lines are good, and the pump and solenoid seem to be working fine.
I have the driver's side apart and I have a couple of questions.
What's a good source for the vacuum seal? I've checked rockauto, riff raff, and diesel o-rings. Diesel o-rings has it, but the description says it's only for 2003+ Excursions so I didn't order it.
There is no yellow o-ring anywhere on the hub. I assume that someone forgot to put this o-ring back in and this is why I don't have ESOF? I guess what I really want to know is that there isn't some 2000-specific thing where there's no o-ring, right?
After I got the hub off, I spun it around on my workbench and it doesn't sound good at all. It makes a slight metallic grinding noise about 1/2 way around. I assume this isn't normal? AFAIK these are all original parts - but the missing o-ring means to me that someone already had it apart.
There was a lot of water intrusion and rusty colored grease but nothing was dry, the needle bearings were intact and the shaft isn't scored at all where the bearing rides. I'm hoping new seals and good cleaning and it should be good as new. And then it's off to the next side.
View 7 Replies
