Ford Super Duty (1999-2016) :: 2003 F250 - Back Tires Spinning While Front Ones Sit Idle In 4x4?
Dec 22, 2008
We have a lot of snow and a lot of ice up here at the moment and my 2003 ford F-250 SC Fx4 isn't performing so well. The truck is stock other than a pair of 285/16R BFG A/T's
I have been noticing that my rear tires will spin while trying to go up hill on some ice or snow covered areas and my front tires just sit still while in 4x4 or 4x4 low. In the case I just described I remain stuck in place until the rear tires can get a grip then I continue up hill. I don't understand why my front tires are not spinning as well, to me this seems just like 2 wheel drive not 4x4. I have been using ESOF most of the time. I have mentioned in other threads that I do plan on upgrading to warn premium hubs, but I am wondering if its that my truck isnt actually shifting into 4x4 or if there is a reason why even in 4x4 my rear tires would spin while my front tires do not?
I am confused because when I shift on the fly while driving I can feel the 4x4 kick in because it just feels different than driving with 2 wheel drive, but then something like I described will happen and I start second guessing myself. What might be happening? It's not that I am opposed to switching to the warn premium hubs, but is that actually going to fix this issue or is my truck acting normally??
View 13 Replies
Advertisement
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 Replies
Yesterday I was parked on an incline with my front wheels on gravel and the rear wheels on wet grass/mud. When I tried to go, the rear wheels started spinning. I then switched on the low 4x4, and tried to go. The rear wheels continued to spin, but the front did not turn. I had new wheels installed, that has a cap that covers the manual locking hub, so I couldn't turn it to lock the hub. What should I look for to fix the problem?
2007 F250 4X4 Larriat SRW
View 2 Replies
After the hard downshifting full throttle highway run low speed stomp on it freeway cruising tires spinning on gravel crawling through town day yesterday -
my tranny just doesn't know what to do!! One thing that it does like to do is make that 6.2 spin and sing! Eventually we'll be on the same page so we can work and play seamlessly.
View 14 Replies
I bought my first vehicle last October, a '99 F-250 with a 6.8 V10. I later found out (AFTER hauling a big load of rocks in a dump trailer) that one of the bottom leaf springs was broken. So this winter I have been thinking on what I want to do about it when it warms up. This is pretty much on top of the "to do" list for my truck. I did make a thread about putting 1 ton springs under it, but I think I'll just stick with the regular 3/4 ton springs. So now this is where I have another question, and I think this pic will tell some of it:
Now I'm not sure if those rear springs are stock, but that rear end is way the heck up there! The truck itself is not level, the front looks to be correct height, but not the back. A buddy at school and I were talking about a leveling kit for the front. But the more I look at it, I think the rear end should come down. I don't want to get bigger tires, as I just put brand new Transforce AT's on the back and plan to put new ones on the front in the near future.
Another question of mine is, would this have been a truck ordered just for pulling a camper? It has holes for a fifth wheel hitch in the bed, the rear end sits high, and it didn't come with a tow package. The PO told me that he put the receiver hitch on it. I'm fixing up stuff on it one thing at a time. Springs just happen to be next on the list.
View 14 Replies
I'd like to replace the back bench seats with something that has a headrest. Can I swap out the benchseat from a 2004 model and place it in my 2003 model?
View 4 Replies
I have a 2008 F250 XLT. When i am driving and turn the wheel a squeak is noticeable while the tire is spinning. as i speed up the squeak gets faster and slower when i slow down. I have it narrowed down to the right front tire but cant figure out what is causing it.
View 5 Replies
2003 f250 crewcab 6.0 auto 4x4. I all of a sudden started feeling a vibration under the truck near the back when I accelerate and when I let off the gas no other time. No noises or clanking just vibration. I can wiggle the driveshaft inside the carrier bearing do you think that could be it or is it the rear end.
View 14 Replies
My idle goes real fast 2500 rpm special when is warm can't get idle to go down for nothing took truck to camping on dirt road with the vibration idle came back to normal and stay for while and over the soon start again. No code...
View 1 Replies
I have a 03 250 gas 5.4 trying to find out the cooling system problem. I've found what I've read to be common oil leaking from back of passenger head. I had never noticed this before but it started very slight now overflow started bubbling over.
There is no coolant in oil no white smoke. My cooling system leak is just head gasket and gasket change could solve the problem or should I did deeper?
View 9 Replies
The 2003 F250 5.4 Superduty has no power and keeps stalling. If I floor the gas it just stalls. I've replaced the pcv valve and line, the fuel pump relay, the fuel pump, and cleaned the tank, changed out the gas, added Lucas, and it just won't run right. Desperate, and no codes are coming up...
View 5 Replies
2003 F250 4x4 7.3L
While doing my brakes in the front, I tried to wiggle the front left, nothing. Solid. Then when I did the right, I was surprised to see it wiggle when I grabbed the tire. So I looked to see what was moving.
Not the U joint, not the ball joints, But it looks like what is a drive shaft.. (I am new to this stuff). On the right side a shaft comes out of the axle just before the U joint and the rest of the wheel assy. What is wrong?
View 6 Replies
I have a bad wobble/vibration coming from front end i think i replaced hub locking hubs u joints truck dont feel safe at all took it to ford they say its normal no way its not just starting doing it few month feels like the 4x4 is in use when hitting bumps when driving if you go slight left or right it seems too make act up more.
View 2 Replies
Have an 03 f250 6.0L and the tie rod from pitman arm moves easily and there isn't a steering stabilizer, noise got worse after I put new tires on front but it's a loud clunk that I can feel. I've replaced the sway bar bushings and end links. Would the worn tired rod make that noise or would it be ball joints?
View 1 Replies
2003 F250 super cab, 335,000 miles. the seats are all in good condition except the drivers seat bottom, no rips or tears but the outer bolster area is worn. Looked at new replacement and no go. Is there a decent cover or a aftermarket replacement that looks good? The truck is not worth high end stuff, just would like it too look better
View 10 Replies
I put some bfg at's on my '16 f250 6.2 today, 285/70r17 from 245/75r17. Has went to a larger tire and had funny downshifts? I had two hard down shifts on the way home from tire shop that I have never had before. I'm hoping this will go away once the computer relearns. Should I disconnect the battery or anything or just drive it and let it learn? I'm a little disappointed, the tires still look tiny, and checking clearances at liners and radius arms, I could have cleared a lot more tire easily. They sure looked bigger on dads '04. These will do me for a year or so until I can upgrade wheels, tires and suspension.
Before
After
View 9 Replies
I've been noticing that one of my front hubcaps has been backing off slightly. I tap it back on and it's good for a while. But lately I'm noticing that I have to tap it back on more often. I took it off today, thinking that I might need a new one. The part number on the inside is IC34-IA096-AB. It's on my 2003 Ford F250 4x4.
I pulled the opposite cover and tried it on the side I'm having trouble with and noticed the same thing. Upon further inspection, I noticed that the chrome plated trim piece that covers the steel rim has tabs that should be flat to the rim. I'm referring to the area where the trim piece ends, near the lug nuts. On the one that I'm not having trouble with, it's flush/flat all around. But on the one I'm having trouble with, some of the ends are not flush to the rim. That is why the hubcap is not seating in those areas. I can see the gap and I can also push down on that section. It's almost as if that trim piece is separating from the rim? I tried using a punch and giving it a couple of whacks with a hammer, but it doesn't press it back to being flush with the rim.
Why would the end of that trim piece that covers the whole wheel lift up on the ends? Is there a way to get it to sit flat?
View 14 Replies
We have replaced 4 fuel pumps on a row.
Voltage is good...even ran a fresh circuit.
Ran new supply lines
But, can't seem to understand the continued drop in pressure. It usually takes about a day of driving to crater after a new pump/filter is installed.
It never dies, just loses power and drops the truck to an idle. Funny thing...if I shut the truck off and turn it right back on...full power for a short period!
The truck is used on a ranch that has plenty of rough roads...thought inertia switch maybe but i believe that would stop fuel completely right?
I am totally stumped and so is the mechanic.
View 5 Replies
I noticed yesterday that my tire on the driver's side has rubbed a flat spot on the rubber brake hose. I bent the metal tubing so that it doesn't rub any more, but should this be of great concern? Obviously I'd hate for it to rupture, but it looks as though it's not too bad.
View 1 Replies
I noticed a moaning from the front end a few weeks back and it seems to be slowly getting a little worse. It is only noticeable when I'm accelerating or maintain speed, but as soon as I let off the accelerator and start to decelerate, it goes away. Sometimes, when the truck hasn't been driven for at least a couple hours, I pull away and there is a really noticeable sort of "clunk clunk clunk" but then it goes away and it just moans. I can also hear some noise from the front end at highway speeds, but of course it is hard to hear much else other than engine and road noise from the cab. It's a 2003 F250 with a 7.3 and four wheel drive.
View 8 Replies
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 Replies
