Ford Super Duty (1999-2016) :: 2005 F250 - Cam Shaft Sensor Replaced - Check Engine Light On?
Sep 10, 2015
You know the "mechanic's fiances truck" problem. I recently replaced the cam sensor in my 05' F250 Gas. The check engine light had been on for a while before that and my truck rode great, however I now want to sell it and I can't do that with a check engine light on. It's got about 85k miles on it.
After replacing the sensor, the light went off for about 20 miles, but it is now back on and my truck seems to miss every once in a while on acceleration or cruising. Some days it's worse than others. The check engine light still says cam sensor, but the sensor is brand new.
My fiance is a mechanic, so I don't know all the details about code numbers and such. However, I want to sell this truck pretty soon, and I would like it to run correctly. His dad (another mechanic) seems to think it could be a coil and wants to wait for that light to come on, but I would rather fix the problem and sell the truck!
View 1 Replies
Advertisement
I have a 05 f250 with a 5.4 I'm having issues with I was driving along the truck started chugging along and the check engine light came on so I checked it with my bully dog the codes that came up were p0192 which is fuel pressure sensor circuit low the next one is p0452 is evaporative emission pressure sensor switch low also came up with p0191 tonight haven't dug into that yet.
I change out the pressure sensor switch from a buddies truck didn't make a difference put my sensor in his truck his worked fine I clean the throttle position sensor and The maf also put a new air filter on not throwing a misfire code but seems like it may be. A little background on the truck it's a 5.4 3valve with a bully dog tuner, mufflers been removed added straight pipe mechanically that's all that's done
View 4 Replies
My dads 05 f250 6.0 PSD. He says he'll take off in the morning and the fuel gauge will randomly drop to empty and trigger the low fuel light, but then also the Check Engine Light will come on. My brother did a code scan and no codes come up. Where we should be looking to remedy this one?
View 14 Replies
I have a ford f250 super duty and it wont start I have checked obvious reasons and I think it might be a crank shaft sensor. Just curious, is there two of them one for right bank and left bank or just one on drivers side?
View 2 Replies
I am running a 2008 Ford F-250 with the DPF Delete and the Mini Maxx Tunner. I have replaced the ECT (Engine Coolant Temp Sensor) as well as the EGR Valve and housing troubleshooting this issue. Both the Engine light and the coolant icon come on when I turn on the vehicle. I am getting a P0117 Engine Coolant Temperature Circuit Low code on the Mini Maxx.
From a cold start with codes cleared if I turn the engine to ON even without starting the engine the Engine codes will come on and the the Mini Maxx will read engine coolant temp 302 and will go into Defueling Mode. I have repeatedly tried removing and reattaching the connector to the ECT thinking it could be loose connection. I can't drive the truck because there is no power and i know the engine is not hot because I have let it sit all night before doing these tests. I do not have a scanner to test other than the Mini Maxx. Other notes: I have checked Coolant I have checked Oil
View 3 Replies
I've owned my 2012 F-250, 6.7L for less than a week and it has a check engine light. The local dealer can't see me for a week, and I need to leave town next week.
I went to AutoZone to have the codes checked and this is what they came back with:
P2033
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
P2031
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
Can I drive on these codes, or should I park the truck until Ford can see me?
View 2 Replies
2005 6.0 F250 SD Powerstroke... Truck died on the road and wouldn't start
The symptoms were... I changed the Radiator and had the cooling system flushed... couple of weeks later it stopped while driving... did some research and talked to a few people and the STC valve seemed to be the issue... So new STC, new intake gaskets, cleaned and new EGR gaskets and I just put in a new Turbo (Ford installed it)... had a stripped bolt under the EGR cooler arm and had to remove the Turbo to get to it.... 14 days later......
Changed STC fitting and gaskets in the high pressure oil pump, IPR screen, exhaust manifold gaskets and Cleaned the EGR and changed gaskets and no start. Tried starter fluid and it turned but wouldn't stay on and the batteries died. Would you all say I'm on the right path?
View 6 Replies
Just replaced the alternator in my 1993 Ford F250. How do I reset my check engine light? It keeps coming on after I drive for roughly 5 to 10 minutes.
View 7 Replies
1-11-11 built F250 with the 6.2. 45K miles. Took it to my local HD truck shop to have the code read. The reader said "Evap pressure sensor switch malfunction", "vac above pressure limit wouldn't bleed". He cleared it and it has now come back.
1. Where is said switch located? Is this something I can do as I'm a seasoned wrench but I'm not dropping the tank in my driveway in the winter.
2. Is it in the tank or outside the tank?
3. Has there been any TSBs or recalls on this before I attempt to repair?
View 6 Replies
So yesterday I decided to wash my truck and after taking care of that I took it for a short drive and the tranny started acting funny. Check engine light comes on and the code is P0500 . It calls for a VSS but I cant locate it. Also the fact that it did after washing the truck is making me think its a wiring issue... F250 SD 5.4 4x4 ....
View 5 Replies
My 2014 F-250 is having a repeat problem with an intermittent cell engine light. About 10000 miles ago it happened, and they changed out the egr cooler. Saying it was gummed up with soot. Problem just started up again. Light will stay on for about 3 or 4 restarts then sir off on its own. It's this a known issue with the 6.7? Is there a way to prevent it?
View 7 Replies
Just this morning I tried to remote start my '13 F250 6.7 and all i got was the doors lock and a two honks. The two honks are usually when there is a door left open when you click the lock button two times but all of my doors were locked. After I started the truck with the key and took it out to go run a errand I noticed the check engine light turned on. Could this be connected or just a coincidence?
View 4 Replies
2002 F250 SD 4X4 5.4L. 4.5 inch pro comp lift tire size 305/75/R16. K&N cold air set up. 208,000kms
I know the truck does horrible on gas but lately is been getting worse, maybe I am getting 350km to a tank. Mixed highway city driving. Sounds like I might have a vacuum leak somewhere but I have no engine light. I've had the truck since last year and put about 10,000km. on it done regular oil changes .. brake maintenance no motor work so far.
View 2 Replies
I have the infamous P0461 check engine light coming up. I filled it with Techron and even purchased Techron additive with a full tank and it's not going away. I've also replaced gas cap with OEM brand new yesterday and light keeps coming on after 2-10 miles.
Truck is stock. Bone stock. The fuel gauge is reading accurately and not fluctuating or jumping or behaving erratically. I checked all fuses and all fuses are good (under dash and on floor in cabin).
2010 f250 lariat 5.4 V8 4x4 super cab 189,XXX miles.
View 2 Replies
Bought a brand new F250 6.7 it has 7000 miles in it now and the check engine light comes on and the truck goes into limp mode. I have taken it in to the dealership twice they said there is no code they can find and they just reset the check engine light and it does ok for a bit then starts the cycle all over again. It also is only getting about 6.5 mpg....
View 6 Replies
2 weeks ago I had the check engine light come up on my 2011 F-250 6.2 XLT. Did a diagnostic check and Codes P2098 and P2272 came up. Did some research and found out the second O2 sensor on passenger side had gone bad. I replaced it with a Motorcraft O2 sensor and cleared the code. It has not came back since. But still not getting the fuel mileage I got before. What else could be wrong?
View 5 Replies
OK....my gas cap (5.4 gasser) wasn't put on properly at the gas station. A couple of blocks later, the "Check Gas Cap" notice came on. I stopped a few blocks later, and installed the cap properly. The notice STILL came on. After messing with the cap 4 more times, I gave up, but the notice is still on. Do I need to have it "erased" like a code, or is there a problem with the cap? Everything LOOKS fine...
View 2 Replies
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
View 2 Replies
(The truck is a 05 f250 with a 5.4l). The problem first started out with the engine temperature gauge spiking and then resetting itself when the truck is turned off and then turned back on. If I drove the truck for any distance it would go into limp mode and the CEL would come on. The code was p1299, which is the cylinder head temperature sensor, and I replaced the sensor but no luck. Then the shop and I went through all accessories hooked up and couldn't find a short until I remembered that my prodigy break controller would occasionally read "ol" or "sh" which both readings are from shorts. I tow a enclosed trailer about 85% of the time and the past week I have been towing it with a different 250 and the same break controller without a problem so I have eliminated the trailer. But the shop just said the problem was the controller and unhooked it.
Now the next day it threw the same code with the controller unhooked and the trailer hooked up. after thinking it seemed that it was happening when i accelerated so I took apart the 7 pin and sure enough there was a little water in it, but after driving it around for a little and no code being thrown I hooked my break controller up and it still was showing ol or sh so i believe there is still a short. Also I noticed that my voltage is reading right at 13v instead of the 13.8-14v it was reading before this issue arose. I think I have narrowed it down to the 7 pin harness and/or electrical in the break components, but do not know what would loop back to the temperature sensor.
View 2 Replies
I got an f-350 drw it is sluggish on take off feels like a miss. Higher speeds when you step on it. It seems o.k I have been told it could be a crank shaft positioning sensor any in put on this. I have changed the fuel filters, cleaned the e.g.r. valve and yes it was pretty clogged,air filter seems to be good. And 1 last thing for now where would c.s.p.s. be located...
View 4 Replies
I have a 1999 F-250 super duty 7.3 4x4 and the rear drivers side axle seal is leaking. My question is how do I remove the axle shaft? my last truck a f150 had c clips in the diff that released the axle shaft but I did not see those on this truck. How to remove the axle shaft?
View 8 Replies
