First, need a wiring diagram for the outputs on the back of the brake controller module? I want to check and see if there is a problem with the connection to the rheostat. I can activate the trailer brakes with the slider bar but not with the brakes.
Second, where I can get a new OEM controller that will replace my old one if I can't "Cypher it out"?
Where I can find a good used or a good deal on a new factory trailer brake controller to fit a 2006 F250 Diesel Truck?
View 1 RepliesI am looking at a 2014 f250, if has all of the options I want on a truck except the brake controller. Can a brake controller be added to this vehicle ? is it already wired for and do you just remove the blank plastic and pop in ? one ?
View 3 RepliesI tow a 5th wheel with my 2014 F-250 that has an factory TBC. I just installed Electric over Hydraulic disc brakes on my 5th wheel and was trying to see if there was a setting I needed to change on the TBC to tell it that is now E/H versus E. In the Information section of the dashboard display it talks about the controller actuating electric drum brakes but the manual talks about it being able to do electric AND E/H. What I need to do here...if anything?
View 6 RepliesI 2000 f250 throughout a few years.
Anyways, I recently aquired a tekonsha voyager (for free) and went to install it, but have run into a problem with the installation.
I searched to find a wire color guide to figure out what wires are which on the under dash connector, but cannot find the answer I'm searching for.
Currently I have a red, green, blue, brown, and yellow wire on the underdash connector, while the tekonsha only has red, white, blue, and black. (I know what colors do what on the controller, but am completly lost on the under dash plug, and can't trace it back without tearing out the entire dash assembly.
I just bought a 2000 Excursion limited v10 4x4. I'm going camping this weekend so trying to install my brake controller. I found the plug but noticed these wires dangling. I can't see the back of the harness. I'm afraid the PO may have cut them to install a universal harness. How to recognize them? I don't want to buy a ford specific harness if the wiring has been cut.
View 3 RepliesI am looking for a wiring diagram for that taillights for a 1999 f350 pickup. I am working on a friends truck that doesnt have any taillights and I would like to have a diagram in hand before I get started on it.
View 7 RepliesI'm currently trying to swap out the standard AM/FM/CD for a DVD receiver with backup camera, and need to find out the proper wiring colors and pin position. I'd rather not send it to a stereo shop, as I've seen a lot of hack work by so called "audio installation experts", and besides.. I have a shop and can do the work myself.
I tried looking through AllData, but since my truck is too new, Ford doesn't release a lot of technical info for us in the aftermarket. Looking for a link to a Ford diagram?
Looking for a wiring diagram for the coolant temp sensor? 1999 F250 SD V10....
View 4 RepliesWhat is the factory radio wiring colors or know where I can find a diagram?
View 14 RepliesMy four wheel isn't working. I have a 2002 f250. When I turn my esof switch the dash light doesn't come on and when I turn on the lights the switch doesn't even light up. I'm going to check for power at the switch but I was wondering to get a diagram for the 4x4 so I can see if there's anything else I can check or look at.
View 9 RepliesJust got an inexpensive LED Stop/Turn/Taillight Bar my problem is it has (3) wires Red, Black and White while the available connection from the old bar has only (2) wires Black and White with Red Dots.
The wiring instructions for the new LED bar says (1) Attach black wire to tail lamp circuit(+), (2) Attach the Red wire to the stop/turn circuit(+) and (3) Attach white wire to a good ground(-) location.
How I should hook this up? My thought is Black to Black , Red to White with Red Dots and White to Frame metal.
I just picked up my 2007 F350 as a replacement for my 2003 F350 (still have the 2003). I really like the uplifter switch option on the truck, I can normally figure things out but I am one of those people who is electrically challenged (home and auto)and also am one who does not wish to butcher the new ride (same for the home)to gain an education in the art of wiring. I would like to reinstall my headache rack lights on this truck as they are needed for winter work. I was in my truck manual and the info for wiring is weak and the website did not respond nor did my email to ford. I have found the wire harness but it is not tagged as a pair/color to switch. I have the lights already grounded to the rack, so I am thinking I just need the hot wire from the switch. Looking for the color code for positive and ground for the switches.
View 14 RepliesI am looking for a site that i can download a service manual with good wire diagrams. I want to install an alarm with remote start and need to know what wires go to what.
View 2 RepliesI've just bought a new 2016 SD xlt. The only extra I wanted that is missing is the factory trailer brake controller. The dealer told me it had to be programmed. I was expecting plug and play and planned to do it myself till they told me that. Is this true?
View 14 RepliesHave recently been getting a "TBC Fault" message and the Beep, as the message goes on and off(annoying) looked around think its the Controler itself,,If I move the slider, and Jiggle it,,the message Blinks on and off as I move the Slider,,,Looking for the method of removing it from the Cubby Hole,,,Gave it a tug,,,and wiggle did not move must have a Clip or Tab to release it.
View 8 RepliesI just had a headache rack built for my truck. Looking to wire in 2 very bright reverse lights, 2 not so bright lights to deal with stuff in the bed of the truck at night, and also mounted a receiver hitch so I can hook a winch up back there when needed. looking for opinions on wiring for all of this. Never wired stuff like this so I'm shooting in the dark. My wiring skills are adequate but not great.
View 7 RepliesI am having an issue with the under dash plug for the brake controller on my 2001 Ford F250 Super Duty. I plugged in my Curt Brake Controller and figured all was good.
As usual with anything I do it isn't that easy. There is no power to the controller or the plug.
Is there a specific fuse I should check or even look to see if it has been installed because apparently this truck never had one installed even though it has a 7 blade plug installed and is plugged into the wire harness in the rear.
We bought a 2012 f550 chassis and had a utility bed outfited. As far as I know the truck does not have a tow package (major F-up). They did install a receiver and electric in the rear. The 7 way pin in the rear does have the appropriate wires (including blue). I can not find the harness in the cab under the dash. I have looked near the radio where I have found the harness on our other trucks. I specifically looked for the red white and blue wire under there. Where is this harness? Is the harness still in the cab even without the tow package? This will be for the old school plug in controller, not the ford intergrated contoller.
View 4 RepliesMy 08, when I connect my 7-pin trailer up, bouncing down the road that message and tone CONSTANTLY going off....drives me nuts! I have went thru the wire harness 2x now, cleaned all the contacts, etc. Any other thing short of a 12 gauge? When it does pop on, the controller starts flashing...I've reached down a few times and manually hit the brakes and it still hits em so whatever it is, I feel its very minor or whatever....just don't know where to go now! All contacts have been cleaned good as well.
View 8 Replies2006 F250 Diesel 125000. Got truck back from dealer pulling out noticed blinkers blinking fast. Figure classic burnt bulb. But upon further inspection no tail lights when headlights on. Ooh and a driver side mirror with blinker that has a crack over the lower light which is side the marker/running light, the light does work. After I Google the issue and see that the MFS is a big culprit I replaced it and have same issue. What I do have working and when:
Brake lights work when headlights off - no key in ignition
Brake lights work when headlights on with blinker on - no key in ignition
Brake lights do not work with headlights on - koeo, koer
Blinkers (rear) when selected both blink
Ignition switch?