Recently purchased 2006 F-550. Noticed the brakes seemed a bit squishy and weren't stopping the truck as well as I thought they might. Looked under the car and saw this at the right rear tire. Give it to me straight, doc.
View 14 RepliesThe brakes seam to be dragging on my F550.It won't roll when out of gear. Noticed a good deal of brake dust on all 4 corners after just a couple hundred miles. Also,when it does roll I can some times hear it creak slightly. At not time does it lose any braking action nor does the brake pedal get hard or soft.I know it will need pads and rotors soon since the rotors are pretty grooved. (Just bought the truck last month....it's on my LOOOOONG to do list.....).
View 3 RepliesThe truck I'm working on is a 2003 f550 with a 6.0, and 382000 kilometers. My service truck died on me couple days ago, while running. As I rolled to a stop, I noticed that my temp gauge on the dash dropped to cold. (Truck was hot). Tried starting, and I have a crank, no start situation.
After towing it to my shop at work, I hooked it up to my scanner, and found that the pcm will not communicate with the scanner (otc genisis). I have no injector buzz with key on, wait to start light comes on for an abnormally long time. I have 48.3 volts on the ficm,(4 screw), and haven't been able to find any chafed wires as of yet.
New issue I've discovered , when stopping , the RPM's drop down to 500, truck acts like it wants to stall , then goes up to 750 RPM's . Then it's fine . Doesn't hesitate when accelerating . Idles slightly rough after start up , about 30 seconds . I've checked the air filter , cleaned the IAC and MAF. Fuel filter is only a year old . What I should check next ?
View 14 RepliesProblem started with the front end shaking a little bit when braking like the rotors needed turning. Then the brakes began to intermittently hum when stopping. Then my ABS light came on. Put the truck up on the stands and disassembled the brakes on both sides. The ABS sensor was chewed up on the driver side. The less than year old hub felt sloppy so I changed it. Put everything back together.
New hub came with new ABS sensor. Went for a test drive ABS light is gone and I no longer shake or experience the hum when applying the brakes. However now when I go to stop right before I come to a complete stop the driver side (new hub/spindle side) I hear what sounds like the grade school class clown making a fart sound with his mouth, and the truck pulls to the driver side. Is the ABS system malfunctioning or is this a caliper issue? Calipers look like they are OEM.
My Dad has a 2006 F550 Lariat with the grey leather seats, and the drivers seat is starting to fall apart. So my Dad is wanting to replace it. My Dad thinks its from a lot of sliding in and out, and having all kinds of dirt and other stuff on it. It has a big spot torn in the lower left of it and then the armrest is starting to rip as well.
So I was wondering where a good place to get some replacement seats for it was. Definitely leather and grey to match the rear seats since its a crew cab. I don't think it necessarily has to be stock, but something that looks good and still at least somewhat matches the rear and rest of the interior.
Here's some pictures of the seat. Nice hole in the floor mat too. I think some nice plastic ones would work and look much better.
06 F550 w/5r110w. Truck and trans runs great then trans acts like it was shifted into neutral, rpm's flare up and if you don't get your foot out of it the trans will re engage aggressively. Changed the speed sensor on the rear axle, there are no codes, had a trans shop change the filters and fluids then change out all of the solenoids. They tell me its not a trans problem.
View 3 RepliesMy 02 F250 has me baffled. For a while the truck would pull to the right when hitting the brakes and occasionally the brake would get hot. To try and remedy this I put a new caliper and hose on the right front corner a new hose on the left front side. The truck still pulled right and the pedal got spongy even after bleeding the brakes 3 times. I got to checking the rest of the brakes and found a seized slide pin on the left rear. Got that fixed and still pulling right with a soft pedal. I've checked all of the sliders and none are seized. I am lost and I cant stand the soft pedal!
View 4 RepliesOk, so I am trying to get are 99 F550 all fixed up and have a few things to ask.
So we have had the ABS light on now for some time. I had it scanned at O Riley's and the scanner said the abs sensor on the passenger side was faulty. So I replaced that and the light was still on. We had taken the truck to ford to get it checked out for a rear end problem we have been having as some of you may know from a previous post I made.
Well ford said it was the rear sensor on the axle that was causing the abs light to come on. So I replaced that. Still have the abs light on. I disconnected the batteries to try and see if that would reset it and it did not. I hooked up the Scan Gauge II and ran to see if it picked up anything. It said it did not pick up any thing. I still did a code clear but it didn't work. If there a tricky way that you have to get the code cleared off?
2nd I was checking the fluid. I noticed that the tranny fluid is over filled quite a bit. Will this hurt it? Should I drain the fluid to where its at the fill line?
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 RepliesOK, so I have the brake pedal downshifting, but there is no real exhaust brake. Can I have one installed, like the latter model 2015 or even the 2016, with the button?
View 9 RepliesI have a 2008 f-550 diesel. Had water in fuel. Flushed the entire system. Replaced the fuel filters and injectors but still will not start.
View 2 RepliesI'm working on a 2000 7.3 that was running but had no power so we changed out all the injectors and glow plugs and rebuilt the turbo now there is no start ...
View 2 RepliesIt has a 7.3 bone stock in it. When it is cranking you can hear a relay clicking. it's behind the dash just below the radio. There are 3 relays together 1 big one which is for trailer lights and 2 small ones which i don't know where they go. but i replaced all 3 and i still hear the clicking ONLY when the engine is cranking.
View 1 RepliesI have a new 2013 F-550 Lariat 200" WB on order. I can and will increase the combination weight on the truck, to make full use of the 19, 500 gvwr. My question is how much will a current F-550 pull on a 5th wheel/gooseneck style trailer before it becomes dangerous? I plan to set the truck up with an 11ft aluminum Eby flat body, with a Holland FW6000 5th wheel placed under the body. I am considering a 35 or 40 ft flat gooseneck.
The combination weight would be changed based upon the axles I choose to put under the trailer. Two 12k axles will give me 44,000 gcwr, two 15k axles will give me 50,000 gcwr, and two 16k axles would give me a 51,000 gcwr. The truck will be able to carry about 10,000-11,000, the trailer needs to take the rest. I am confident that 44,000 gcwr will not be a problem, but the idea of 50,000, or 51,000 really makes me question safety. So, how much have you hauled with a F-550, and a gooseneck trailer?
New to me 2012 F550 parking lights will not go off. Battery disconnected now. Touch battery cable parking lights come on.
View 14 RepliesI have a 2001 F550 flatbed tow truck with a 7.3 and the ZF 6 trans. i put a Luk clutch flywheel pressure plate new throw out bearing new clutch fork New clutch slave cylinder and master set up. When i push the clutch in it is VERY EASY compared to the way it was before. Ane when you push the clutch in and put it in gear you can hear the clutch disc rubbing on the flywheel and if you lift your foot the thickness of a hair the truck takes off. Also i can't engage my PTO because the clutch is not disengaging all the way. there is No adjustments on this set up. What Now.
View 2 RepliesI have a 1999 Ford F550 with a 6.8L V10 and a 4R100 Auto.
I want to run an underhood hydraulic pump, like what a wrecker uses only I want to use it to run a generator under the truck.
How can I get a 6.8 to idle up to 1200 or so? I searched the Body builders guide and it looks as if the idle up is for the 7.3 only.
My truck also is not a 2005 and up like the other posters, who can take advantage of a drive by wire.
Also I doubt my transmission has a PTO cover so I think a generator option using that route is a dead end. What are my options to idle the truck up to 1200?
I have a new to me 1999 f550 w/ 7.3 and I have installed an aluminum service body with a crane on the passenger side bins. The crane itself weights about 650lbs plus the steel frame it is mounted on (superstructure in the aluminum service body). I'm concerned about the uneven load on the rear suspension. It does sag slightly to the passenger side - guessing 1" - I will measure tomorrow.
1) Should I be concerned?
2) What can I do to correct it? (without just adding weight to counter balance it).
I am trying to figure out where the relay would be when i look online for the map of the relay box under the hood it says nothing of a horn relay. I don't have a key fob for the doors to unlock so I wouldn't think its tied to the computer. Should mention nothing happens when you hit the horn also fuse is fine. No power at the actual horn when i hit the steering wheel(horn)....
View 8 Replies