Ford Super Duty (1999-2016) :: F550 V10 High Idle Up To 1200 Or So
Jan 25, 2015
I have a 1999 Ford F550 with a 6.8L V10 and a 4R100 Auto.
I want to run an underhood hydraulic pump, like what a wrecker uses only I want to use it to run a generator under the truck.
How can I get a 6.8 to idle up to 1200 or so? I searched the Body builders guide and it looks as if the idle up is for the 7.3 only.
My truck also is not a 2005 and up like the other posters, who can take advantage of a drive by wire.
Also I doubt my transmission has a PTO cover so I think a generator option using that route is a dead end. What are my options to idle the truck up to 1200?
View 2 Replies
Advertisement
Ok, so I am trying to get are 99 F550 all fixed up and have a few things to ask.
So we have had the ABS light on now for some time. I had it scanned at O Riley's and the scanner said the abs sensor on the passenger side was faulty. So I replaced that and the light was still on. We had taken the truck to ford to get it checked out for a rear end problem we have been having as some of you may know from a previous post I made.
Well ford said it was the rear sensor on the axle that was causing the abs light to come on. So I replaced that. Still have the abs light on. I disconnected the batteries to try and see if that would reset it and it did not. I hooked up the Scan Gauge II and ran to see if it picked up anything. It said it did not pick up any thing. I still did a code clear but it didn't work. If there a tricky way that you have to get the code cleared off?
2nd I was checking the fluid. I noticed that the tranny fluid is over filled quite a bit. Will this hurt it? Should I drain the fluid to where its at the fill line?
View 3 Replies
I'm going to cut right to the chase, when did ford stop having the diesel high idle when it is cold? I have a 2015 350 I bought last August and assumed it would high idle like previous power strokes. I even put a ts6 chip in my 97 just for high idle option to keep the motor warm when idling around our farm. I realize ford probably doesn't want trucks idling long because it kills mpg and isn't good for the emission system but to be honest I could really care less about mpg as long as it's decent and a high idle would keep emissions pushed through. Is there an option or anyway you can get the 6.7 liter to high idle?
View 1 Replies
I just got a 2003 f250 5.4 triton and it has a terrible knock. I've hear of the cam phaser problems but this thing knocks at high rpm and at idle so I doubt it would be a phaser, I thought it could be a rod bearing but I'm not losing any oil pressure. Its a pretty loud knock I don't have money for a mechanic to diagnosis it...
View 3 Replies
OK, so I have the brake pedal downshifting, but there is no real exhaust brake. Can I have one installed, like the latter model 2015 or even the 2016, with the button?
View 9 Replies
I have a 2008 f-550 diesel. Had water in fuel. Flushed the entire system. Replaced the fuel filters and injectors but still will not start.
View 2 Replies
I'm working on a 2000 7.3 that was running but had no power so we changed out all the injectors and glow plugs and rebuilt the turbo now there is no start ...
View 2 Replies
It has a 7.3 bone stock in it. When it is cranking you can hear a relay clicking. it's behind the dash just below the radio. There are 3 relays together 1 big one which is for trailer lights and 2 small ones which i don't know where they go. but i replaced all 3 and i still hear the clicking ONLY when the engine is cranking.
View 1 Replies
I have a new 2013 F-550 Lariat 200" WB on order. I can and will increase the combination weight on the truck, to make full use of the 19, 500 gvwr. My question is how much will a current F-550 pull on a 5th wheel/gooseneck style trailer before it becomes dangerous? I plan to set the truck up with an 11ft aluminum Eby flat body, with a Holland FW6000 5th wheel placed under the body. I am considering a 35 or 40 ft flat gooseneck.
The combination weight would be changed based upon the axles I choose to put under the trailer. Two 12k axles will give me 44,000 gcwr, two 15k axles will give me 50,000 gcwr, and two 16k axles would give me a 51,000 gcwr. The truck will be able to carry about 10,000-11,000, the trailer needs to take the rest. I am confident that 44,000 gcwr will not be a problem, but the idea of 50,000, or 51,000 really makes me question safety. So, how much have you hauled with a F-550, and a gooseneck trailer?
View 11 Replies
New to me 2012 F550 parking lights will not go off. Battery disconnected now. Touch battery cable parking lights come on.
View 14 Replies
I have a 2001 F550 flatbed tow truck with a 7.3 and the ZF 6 trans. i put a Luk clutch flywheel pressure plate new throw out bearing new clutch fork New clutch slave cylinder and master set up. When i push the clutch in it is VERY EASY compared to the way it was before. Ane when you push the clutch in and put it in gear you can hear the clutch disc rubbing on the flywheel and if you lift your foot the thickness of a hair the truck takes off. Also i can't engage my PTO because the clutch is not disengaging all the way. there is No adjustments on this set up. What Now.
View 2 Replies
New too my Ford, but anyway it's -10 Celsius. My trucks been idling for a few hours and probably will all day because of my job. Usually idles about 600rpm normally. So today the oil temp was about 80degrees Celsius. Then the truck idled up too about 1000rpm for a while. If I touch the gas it goes back to normal idle speed but then starts idling up again after 30 sec. What temp does the truck want too keep it at?
View 3 Replies
I have 2005 f250 5.4l 3v that was having miss problems between 1200 and 2000 RPMs. Changed VCT solenoids which worked, but then could hear chain hitting cover when powering down throttle on left side. Figured chain tensioner was bad, so tore down and removed timing cover. Found left chain was tighter than what seems normal, and right side had huge amount of slack. While taking off tensioner on left side, something happened to fast for me to see it, and still not sure if what happened wasn't just my imagination. I thought that the chain moved very fast for an inch or two. Anyways, I watched how to video on timing the 3v, but I am very confused about it. The left bank seems to line up on timing marks perfectly, but the right chain is off by at least 2 1/2 links. Not knowing any better, I removed three rockers on left bank (2 intakes and 1 exhaust) but only removed two intake rockers on right side. I don't know what I am doing and getting scared.
View 1 Replies
I have a new to me 1999 f550 w/ 7.3 and I have installed an aluminum service body with a crane on the passenger side bins. The crane itself weights about 650lbs plus the steel frame it is mounted on (superstructure in the aluminum service body). I'm concerned about the uneven load on the rear suspension. It does sag slightly to the passenger side - guessing 1" - I will measure tomorrow.
1) Should I be concerned?
2) What can I do to correct it? (without just adding weight to counter balance it).
View 7 Replies
I am trying to figure out where the relay would be when i look online for the map of the relay box under the hood it says nothing of a horn relay. I don't have a key fob for the doors to unlock so I wouldn't think its tied to the computer. Should mention nothing happens when you hit the horn also fuse is fine. No power at the actual horn when i hit the steering wheel(horn)....
View 8 Replies
Really love my 2013 F550 but the door chime is driving me crazy. On my 2003 f150 you could just drop the column cover and unhook one wire running to the tumbler. So I had a look and found it to be totally different. How to unhook it on this truck?
View 2 Replies
Recently removed a plow and wiring harness from my 00 F550 and now my headlights no longer work. The headlight plugs have an adapter that the plow harness plugged in to and it now appears I need some type of end plug on each one to complete the circuit. The problem is the dealer doesn't understand what I need and doesn't think there is such a part out there. Perhaps my thinking is all wrong.
View 3 Replies
I bought a new Motorcraft door latch for my F550 because the door latch won't stay latched. You close the door firm and it seats well then pops loose the first bump in the road. I found all kinds of OEM replacment latches all over the internet but nowhere can I find any instructions or videos or any talk of the best way to go about replacing the door latch. I know they wear out from constant use on the drivers side.
View 2 Replies
I am looking for the location of the fuel pump relay for my 1999 Ford F550 V10 4WD Gas truck.
I have replaced the fuel filter and fuel pump. When the key is turned the pump gets juice and 2 seconds later is not getting juice. No lines are coming into it, so it's not getting up to pressure and shutting off.
View 3 Replies
I recently bought a 2007 F-550 bucket truck with a 6.0 Diesel. Noticed the trucks gauge cluster and radio go on and off..
And on top of that the entire truck died on me yesterday suddenly while driving and there was no power (no dome no lights no ignition not even a click completely dead)..
When that happened I was searching for a large battery cable shorted or pinched under the omnivan body and didn't find anything, Removed batteries, charged with in minutes, re installed and everything came back on..
View 1 Replies
Just got done with a ball joint replacement on my 2003 F550, everything went together great, just as it should. Until I got to the drivers side hub lock.
I have Mile Marker 449s/s manual hubs. Turn from free to lock and theres this loud clicking sound about halfway to LOCK (passenger side doesn't do this). Hub will stay locked for about 2 rotations, then it unlocks and makes a clicking sound. You cannot turn the hub back to FREE, it gets halfway and stops. I tried forcing it and broke the spring fingers inside. Have a new set on order.
Is this a locking hub issue or an assembly error? I was going to take these steps.
- Take passenger side hub lock off and see if it operates normally or same on drivers side.
- If same, remove axle and re-seat/re-assemble everything again
Anything to specifically check? All the parts went back in, washers were in correct order, outer snap ring is in groove.
View 11 Replies
