Ford Super Duty (1999-2016) :: 2006 - Rough Idle - Mid Range Misfire - Low Compression
Nov 26, 2016
2006 F53 (motorhome) with 6.8L V10. Rcently noticed rough idle and midrange (under load) mis fire. Had codes on 2 coils. Replaced coils and put new spark plugs in. Did not improve and now detecting mild back fire.
Just completed compression test. 1=207psi, 2=200, 3=210, 4=190, 5=197, 6=200, 7=200, 8=170, 9=202, 10=208.
put some oil in #8 and retested at 225!
Other observations on #8. Engine has ticking noise chased with stethoscope to #8. THE new plug with 200miles, insulator going to electrode tip and everything inside combustion chamber is black. All 9 other plugs still look new out of box.
With the ticking noise I was suspecting valve but the compression test with oil jumped way up.
View 8 Replies
Advertisement
2006 F53 (motorhome) with 6.8L V10. Rcently noticed rough idle and midrange (under load) mis fire. Had codes on 2 coils. Replaced coils and put new spark plugs in. Did not improve and now detecting mild back fire.
Just completed compression test. 1=207psi, 2=200, 3=210, 4=190, 5=197, 6=200, 7=200, 8=170, 9=202, 10=208.
put some oil in #8 and retested at 225!
Other observations on #8. Engine has ticking noise chased with stethoscope to #8. THE new plug with 200miles, insulator going to electrode tip and everything inside combustion chamber is black. All 9 other plugs still look new out of box.
With the ticking noise I was suspecting valve but the compression test with oil jumped way up.
View 14 Replies
My F53 motorhome has a rough idle and hard misfire but is not setting any codes. I've put new plugs in it and not change.
View 7 Replies
I bought this 2004 V10 Ford truck new.. It was at that time top of the line Ranch King with all the bells and whistles.. I have been trying for some time to figure out the miss I have. I was told yesterday that.. Misfire 2nd cylinder passenger side no compression.. They said I need to have a new Engine installed.. They would look for a rebuilt and would cost with installation around 5 grand.. I then took it to another garage and was told that's not it, but will check it out later in the week.. What I should look for.. No one seems to b able to figure it out.. I cannot afford a new truck at this time and 5 grand for this one to fix is not a reality..
View 8 Replies
2001 f250 v10 6.8l runs a little rough at idle, low rpm is ok between 1700 and 3000 rpm but around 3 it starts to shudder while driving let off gas get back on its fine, new plugs 1,000 miles ago has throttle body spacer and cold air intake, stock everything else..
View 8 Replies
I have a 2002 F250 CCSB Lariat 4x4 with the Triton V10, I'm up to 232,000 miles so far and fairly happy with the old girl. Just this weekend, I noticed some hesitation when at idle and even more rough running when under slight load. The misfire/hesitation is worst when going up a slight hill, when the truck is accelerating at low RPMs.
I am getting zero trouble codes or freeze frame conditions on my scanner. What should be my order of diagnosis? Vacuum test at line from PCV to TB, COP test? EGR inspection? Plug inspection? Also, how do you test a coil if resistance is not a reliable method?
View 5 Replies
I have an 06 F-250. I have had this truck since Oct 2013 and had never use 4 wheel drive here in southern Alabama, so my question is i lock my hubs, turn my selector to 4 high and it works. Now selecting to 4 low and I get nothing.
View 9 Replies
I bought a used Ranger a couple months ago and it ran fine when I test drove it but a week later it started having a misfire every now and then at idle.. I must have gotten pretty unlucky with the test drives..
The misfire comes and goes, it will run fine for a week or two and then it will misfire at idle for a week or two. It only seems to misfire at idle, the truck runs rough/shakes but once you give it a little gas and start moving it goes away. Usually it has a check engine light on from startup when it's misfiring and it goes away on days that it's running fine; it will occasionally misfire at idle with no check engine light. Sometimes when its running really rough the CEL flashes while it's misfiring at idle and I've actually restarted it real quick and the misfire went away for a bit. The engine codes that come up are misfire on startup and misfire on cylinder 4.
I've tried cleaning the MAF sensor, replacing the fuel filter, testing for spark and compression. Compression was 150-155 PSI on all cylinders, however, the compression on cylinder 4 is different depending on whether the truck is running well or not. When it's misfiring the compression on cyl. 4 is 90 PSI and when it's running fine it's 150 PSI. I'm not sure what could be causing intermittent low compression like that?
View 5 Replies
I have a 2000 F250, SuperCab, 5.4 triton, 100,000 miles. It's been a great truck - got it at 63,000 miles. Once engine warms up, it has rough idle, and shift rough. I can give it gas to RPMs up and it smooths out some but is low on power. If this was my 76 F150, I would guess the vacuum hose off the intake manifold to the transmission came loose.
View 6 Replies
I've got a 2003 6.0 that's got a rough idle and low power situation. Doesn't matter hot or cold it has a hard start issue but when it finally starts it has a rough idle, sometimes it has low power on take off but not always. FICM has 48.8 volts coming out, exhaust just had a new y-pipe (had a cracked bellow) absolutely no smoke coming out. When I drive it hard it's like a rocket no rough spots just did oil with filters and fuel filters, blue spring upgrade, and cleaned out the turbo.
View 2 Replies
V-10 running rough at idle, chugging. a problem has developed with my 2004 E-350 V- 10 after having a new fuel filter installed and the induction service done . Picked it up from a local shop and it was running rough after bringing it in when running great! I figured maybe it fouled a plug or something so I drove it home but it didn't improve so I brought it back and had new plugs installed. It is still running rough and wanting to almost stall when accelerating from a stop and the shop cant figure it out , not showing any codes.
I'm thinking maybe they caused some type of vacuum leak that is so far undetected. The killer is it came to the shop running great !!
No other problems with the vehicle, I drive it every day and have owned since new. 278,000 on it now and it has been the best vehicle I have ever owned.
View 8 Replies
I recently purchased a 1999 6.8L. Runs great when cold but after warming up the idle gets rough. Truck has new plugs and coil packs and fuel filter. Checked the fuel pressure and the idle is right at 30 psi. I read that the good pressure range is 30 to 45 psi. Is 30 psi acceptable or should I replace fuel pump or regulator? Any next step to solving my idle woes.
View 3 Replies
Last night, I left it running while unloading a trailer and come back to notice it was idling abnormal. I jumped in it and tried to move it and there was a noticeable loss of power. I unhooked the trailer and tried to get it home. I only made it 1/2 mile down the road when it started spitting and sputtering (surging ever now and then) to a level that it died completely. I was able to start it back and get it out of the road but had to be pulled into a drive. It got to a point it wouldn't start back at all.
Today it started up however still had a rough idle and really has no power to speak of. The more I messed with it the less power it seem to have.
I have searched the forums and tried these things:
1) Checked the oil and noticed it was on the low end of the operating range. I put some in it to put it back to normal.
2) Disconnected the ICP
3) Changed the crankshaft position sensor
4) I dumped the fuel bowl after it completely died (in case it had any water in the fuel bowl).
The fuel filter was just changed 2 weeks ago. The fuel pump seems to be operating correctly (or it at least refilled the bowl) and started again with a very rough idle.
It doesn't have a engine light on nor do I have anything to read any codes it may be showing.
View 14 Replies
I am new to the v10 I only ever owned 7.3 this is my father truck it's a 99 with 200k on it. The problem is it will idle fine when cold but when it is warned up very ruff idle no codes and when I go back at the end of this week I will check the O2 sensor with AE but I really don't know much about it.
View 2 Replies
I have no compression on #4 cylinder. Is there any way to check the cylinder for damage. So I can just replace that piston if it's good?
View 1 Replies
We have a 2008 f250 super duty with the 5.4 triton well ever since I replaced the power steering pump its been running raggedly, it idles rough and when i get up to 50, 55, 60 the check engine light comes on i put a diagnostic reader on it and said something along the lines of ECU bank 1 an Bank 2. What that is and I've been a mechanic for almost 3 years.
View 2 Replies
I have a 99 f250 5.4l 2v with 165000. just two weeks ago i went to start up the truck on a job site to take lunch and it was running really rough. I talked with a mechanic at my shop and he said that it sounded like the aic or that i needed plugs. I went and bought aic and plugs and installed them all in one day. I unhooked the battery before i did any work and have changed the coil packs about 3-4 months ago when it was jerking at highway speeds. I am at a loss.
Read so much on the site about could be this or that and cant afford to through money at it like the govt does. I replaced the ait(air intake temp sensor) and the ect(engine coolant sensor) after i got a code from oreillys that said p0113 which is high input on it. I have read it can be so many things and it seems to be running rich because i am getting about half of mileage i was getting before problem started. i need a fix soon as i must drive the truck to work everyday which is a 52 mile trip total.
View 14 Replies
I have a 2002 F350 with a V10, this just started happening where at times the truck will turn over but won't run... after a few times of trying to start it I pull the key out let it sit for 5 seconds then put the key back in and runs perfect..... now at the gas station the other day it started but ran like it was on 4 cylinders... I turned it off and restarted it and runs perfect. Heading to Kansas next week to pick up my boat and don't need problems....
View 4 Replies
2005 250 5-speed total oil pressure loss ... At 110k mechanic diagnosed failing phasers from noise, rough idle, loss of power under 1k rpm. (Crew cab long box xl bought new for $25k)(first 100k were from carpenters (hard miles) so this truck is barebones and usefulness is much higher than cash value). Truck has 146k
All symptoms typically disappear over 1k rpm so I have limited idle time and manipulated engine speed to try and maintain 1000-1200 and all has been well for past 36k miles. Today noise (valve clatter?) persisted at all rpm and during a scramble to get off the highway all oil pressure was lost (I'm aware that pressure gauge on dash is not 100% reliable). After total pressure loss I cut engine and called tow truck. Out of curiosity, I actuated ignition and motor cranked maybe two rotations, and then appeared seized. After about 45 min waiting for tow I went back to disengage 4wd and take my rifles and skis out of truck. At this time I actuated ignition again and engine fired and ran as it had for past 36k miles. I drove about one mile constantly watching oil pressure gauge, then noise returned followed by instant drop from normal to 0 pressure (dash gauge) I immediately shut of engine.
I am a mechanical engineer, but not a mechanic. I am familiar with the cam phaser system and I understand that their operation is directly related to oil pressure. Today's temp was under 0'F. I have a very skilled mechanic who works for around 30-40% of cost of licensed shop and I know his skills to be on par.
View 4 Replies
I've got a 2015 F250 with a 6.2 Liter with no compression on 3 cylinders. The dealer just diagnosed it and has not opened it up yet but the mechanic says it is probably a broken valve spring...that it is not uncommon in this engine.
My concern is not repairing the spring my concern is what a "free spinning" piston in 3 cylinders does to the life expectancy of the main and connecting bearings in this engine. I have rebuilt engines in the past and I have bought re-built from auto parts stores and from Jasper and I have never had any last more than 60-70K miles. It seems to me that even with very little mileage on the engine with three of eight pistons jumping around under no pressure that there could be considerable scarring of the bearings or bearing surfaces. I am no expert by any stretch but this is an engine in atruck that has less than 22K miles on it and I ain't real happy about opening it up let alone trusting for the next 280K miles that the bearings have more wear on them than they should have. It was only driven about 20 miles total like this but that is a lot of pressure on a highly tuned and pretty darn precision machine.
This is the newest vehicle I have owned since 1988 and I meant for it to be the last pickup I drive (I drive 'em til the wheels fall off) but I am not overly confident that even if this is a one off problem that it hasn't caused even more damage that won't show up for another 100K miles or so???
View 6 Replies
I have a 2000 ford f250 5.4 2v that's been having a shaking at idle and no power what so ever. I tried diagnosing it myself and came up with nothing. I finally decided to take it to the dealer and they are telling me that the right side has no compression on 3 cylinders. They want almost 7000 for a new engine. I was wondering if it was possible to get away with just putting a new head on the right side?
View 13 Replies
