Ford Super Duty (1999-2016) :: 2007 4x4 Hub / Bearing Assembly Part Number
Nov 4, 2016
I am not sure mine are done yet, but I was told by mechanic that they are failing and that the fronts aren't spinning as smooth as they should when up on the jack. They were investigating a sticky caliper at the time and said they believe heat from failing bearing caused that issue. I figured I'd do a little looking for parts pricing just incase. Does come with everything needed to change it? From reading, I found part # 73CZ-1104B is that the one?
View 6 Replies
Advertisement
I have an 2003 F250 with a nosiy alternator and need to change the bearings. I would like to have the bearings on hand before i take it apart. What is the part numbers for the bearings I need?
View 3 Replies
Replacing the backing plates on my rear end, figure get new inner bearings and seals in there. Bearings seem fine but cheap insurance, dont wanna pull it all off again.
When i pulled my hub off, the hub seal stayed on the housing shaft, this is normal? Just gotta pry it off there somehow?
Then new seal-TIMKEN 370247A just tap it into the back of the hub? Also is this the right inner bearings? TIMKEN NP114036
View 1 Replies
2007 F250, V10. What is the part number for the transmission filter?
View 3 Replies
How can you tell when your wheel bearing/hub assembly is going bad? I am hearing what sounds like "metal-on-metal" and I've already changed the brake pads, but the sound still persists. I was thinking about changing out the brake rotors since I did notice an inch long score on the rotor when I was replacing the pads. I don't want to spend a couple hundred dollars on rotors to find out it was my wheel bearing/hub assembly all along.
View 8 Replies
I'm trying to locate the part number (and a replacement) for the plastic piece that covers the top of the tailgate (when its shut) next to the step. It's about a 12 to 16 inch long piece of plastic which has some broken tabs on it, so everytime I drop the tailgate, it either flies out or starts to... I checked the fische online and I don't even see it in the picture. I did find some one-piece parts called "tailgate spoiler cap" but I didn't find any to fit a 2014 F-250 with the step on the tailgate. Should I just tell the wife to go hot-glue it ?
View 1 Replies
I'm wanting to get a single in-line steering stabilizer for my '05 F250 4x4, but I can't seem to find any that include brackets.
I don't need a dual setup because I'm not running a big lift or big tires, but I want an inline stabilizer so that I can just leave the stock one in place.
What is the part number for one that comes with the mounting brackets?
View 7 Replies
Parking brake lever for the park brake on my 2001 F250 srw. Both are rusted up but im having trouble finding the part.
View 1 Replies
I have a really loud whining kind of noise found that its the wheel seal rubbing on the inner part of the wheel bearing. I was just curious if its safe to drive with the spindle removed from the axle?
View 5 Replies
Can't seem to find a number for just the bearing and snap ring. All I can find are the dang assemblies.
View 11 Replies
I just put a new front driver side wheel hub assembly on last week and i discovered two things. The metal plate that goes in behind the wheel hub assembly needs replaced but idk what it is and i need a new axle seals. But when i put the new hub assembly on, the abs light came on and i cant seem to figure out why? Also my front drivers side of the truck is still making a clunk noise when i hit a bump. Input on that too?
View 6 Replies
I am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 Replies
My blower assembly (not at the blower but in the box below it) is filling up with water. Any way to look into besides drilling a hole in the bottom of the box?
View 1 Replies
A cab light (OEM) has burned out. I'd like to replace it. What style/part number bulbs are used?
The closest tangential reference I can find is to 194, with additional references to 168 and 912. A Google Image Search of makes it seem like I'm getting warmer.
View 4 Replies
Today I noticed a leak at the heater hose assembly at the right rear of the engine compartment. It appears to have special connectors and that appears to be where the leak is coming from.
View 1 Replies
My 2002 F250 is knocking loose the front end assembly--the gasket is worn out. So I was shopping around and was considering a beefed-up front end assembly.
View 3 Replies
Actually the previous owner of my 7.3 Dually cut the muffler out and straight piped it, it's really not that loud but too much drone for long highway hauls.
What's a good replacement muffler for a 7.3? Wouldn't mind a little bit of sound, it already has an oversized tip.
View 14 Replies
I was just in the middle of doing the V Code leaf spring swap and noticed a broke part where the u-bolts sit and what looks to be attached to the trac bar. The piece is broken in half and I am not sure how this happened or when. The piece is welded to the axle.
2003 Excursion 4x4 6.0...
View 6 Replies
So, my 2004 F250, CCSB, Fx4, 6.0l, truck broke the carrier bearing today. There is an annoying hum that modulates, the drive shaft has a lot of play and there is light visible at the top of the bearing. The problem is that it broke on a 550 mile trip to Franklin, TN and I need to make the return trip. Is there anything catastrophic that can happen running it this way?
View 14 Replies
I am not sure which it is but I cannot turn the pulley by hand. How do you tell if the pulley is bad or the whole compressor? I went out to start the truck and it wouldn't start. It died so I restarted it and then I seen the smoke from the front of the truck. I opened the hood and the flipping belt was just hanging there. Is there a way to just bypass the unit for now? I wont be needing the AC till summer and that is several months away.
View 3 Replies
Sunday I bought a 2001 f250/5.4 to replace my 91 f250. I didnt drive it yesterday, but this morning on my drive to work the heater was very weak, it seemed to blow warm for the most part, but was barely pushing air even on high. I flipped it over to A/C to see if it blew any harder and it did. Does the blower motor need replace? if so why does the AC blow harder than the heater?
View 14 Replies
