A cab light (OEM) has burned out. I'd like to replace it. What style/part number bulbs are used?
The closest tangential reference I can find is to 194, with additional references to 168 and 912. A Google Image Search of makes it seem like I'm getting warmer.
A week ago last Saturday I bought a 2006 F250 Lariat Crew Cab with the 6.0 and 4WD. The truck is really clean and only has 68,000 miles on it. Here's my question: I needed to tow a boat today and I discovered I have no power, at all, at the trailer light plug receptacle. Nothing at the 7-pin nor the flat-4. I looked through the manual and checked every fuse that had the word trailer associated with it and I can also feel the turn signal relays clicking with the flashers on.
Am I missing something really simple or do I just need to follow the wire harness from the back and look for something that is not connected? It seems kind of weird for it to be just....dead.
I have been having some inconsistency with my transmission in my 2005 F350. I bought it used 2 months ago and have had the low/tow overdrive light blinking. a month ago I removed the pan and changed the filter in the transmission. I had a friend run the diagnostic test and found transmission solenoid code as well as both cat. converters as well as my Number 8 cylinder misfiring... I pulled the transmission pan and filter to find what appears to be 7 solenoids? Where to start?
View 1 RepliesHow to change my map light bulbs over the front seat of my new (to me) 2010 F250 King Ranch with a sunroof. I have tried to remove the whole assembly with a plastic trim tool with no success. I have pulled as hard as I dare and figure there must be a procedure I am missing. It appears to me that the whole assembly has to be pulled down.
View 6 RepliesThe battery light blinks in my truck. It's not a controlled blink, but it flickers like a loose bulb. It started a week or so ago. It would blip every once in a while. Gradually it would start to flicker more often. At first I thought it was belt-related but it isn't related to the transmission shifting at all. So if you're thinking that it's belt-related, you're going to have to explain why it doesn't blink either right before or right after a transmission shift (i.e. a rapid change in engine speed).
Earlier in the week, the light was flickering so hard that it was virtually on. I drove home last night and didn't see it once, although that's the first time I haven't seen it happen at all in a week. The battery gauge itself doesn't move a bit while this is happening. I have a cigarette lighter voltmeter and it shows a pretty steady 14.1 volts regardless of whether the light is flickering or not.
I had the batteries tested in my truck by a real battery shop about 4 months ago and they are fine. The battery connections all seem tight and clean, and the belt, tensioner and all that seems fine. So..What can cause a battery light to come on that isn't voltage related?
How to remove the orange cover to replace the bulb in the driver side mirror - tried but worried I'm going to break it...
View 2 RepliesI bought this truck used and the guy said it needed a new blend door actuator so I bought a new one off eBay I installed it, plugged the wire back in and turned on the key and it started smoking, it burned up. The wires have been cut before and have been butt connected back together. I notified the place I bought it from and they sent me back a new one but I'm scared it will do it again.
View 3 RepliesI need diagnosing why my A/C isn't working. I'm wondering if my clutch staying engaged has burned up my compressor before or after my clutch went bad. I don’t think it’s the air gap issue because I took my clutch off and checked and there were zero washers. I guess somehow I re-installed it with no washers maybe the last time I fooled with it.
I've only knew to check the air gap trick and when that didn't work, I wasn't sure what my next step could be. I tried looking at the high side pressure switch connector to see if it was burned up and it looked ok.
Can track down if my compressor is still good and replacing my clutch is the only thing I need to do or if I need to replace my compressor? Or if there's something else that's totally unrelated that I need to check?
I am not sure mine are done yet, but I was told by mechanic that they are failing and that the fronts aren't spinning as smooth as they should when up on the jack. They were investigating a sticky caliper at the time and said they believe heat from failing bearing caused that issue. I figured I'd do a little looking for parts pricing just incase. Does come with everything needed to change it? From reading, I found part # 73CZ-1104B is that the one?
View 6 Replies2007 F250, V10. What is the part number for the transmission filter?
View 3 RepliesI'm trying to locate the part number (and a replacement) for the plastic piece that covers the top of the tailgate (when its shut) next to the step. It's about a 12 to 16 inch long piece of plastic which has some broken tabs on it, so everytime I drop the tailgate, it either flies out or starts to... I checked the fische online and I don't even see it in the picture. I did find some one-piece parts called "tailgate spoiler cap" but I didn't find any to fit a 2014 F-250 with the step on the tailgate. Should I just tell the wife to go hot-glue it ?
View 1 RepliesUsing LED replacement bulbs? I have a 2008 super duty. Want to upgrade lighting.
View 14 RepliesI have an 2003 F250 with a nosiy alternator and need to change the bearings. I would like to have the bearings on hand before i take it apart. What is the part numbers for the bearings I need?
View 3 RepliesI'm wanting to get a single in-line steering stabilizer for my '05 F250 4x4, but I can't seem to find any that include brackets.
I don't need a dual setup because I'm not running a big lift or big tires, but I want an inline stabilizer so that I can just leave the stock one in place.
What is the part number for one that comes with the mounting brackets?
Replacing the backing plates on my rear end, figure get new inner bearings and seals in there. Bearings seem fine but cheap insurance, dont wanna pull it all off again.
When i pulled my hub off, the hub seal stayed on the housing shaft, this is normal? Just gotta pry it off there somehow?
Then new seal-TIMKEN 370247A just tap it into the back of the hub? Also is this the right inner bearings? TIMKEN NP114036
Parking brake lever for the park brake on my 2001 F250 srw. Both are rusted up but im having trouble finding the part.
View 1 RepliesI have searched everywhere, but I can't find the information I need for anything newer than 2007. I have the instrument cluster removed, and I can't figure out how to get to the bulb. In previous years, it just twisted out, but this one is different.
View 7 RepliesI'm really not satisfied with my Ford F350 SDC headlight bulbs!! I need a BRIGHTER bulb suggestion that won't break the bank and not have to add ballasts and rewire the circuit...
View 11 Replies2013 F350 passenger headlight bulb keeps blowing both high and low? Replaced 2 times now?
View 1 RepliesI have a 2001 f250 5.4 triton. My cb antenna hole leaked water in cab, soaked my fuse block. Horn goes on and off, radio turns on without key in ignition, truck only starts when key is on and I bridge solenoid, and number 4 coil is not firing. I have let truck dry out, fixed the leak. Everything is bad to normal except starting issue and coil issue.
View 6 Replies02 f250 SD...I need to change the front corner turn signal bulb... How the hell do I get to it? I see the grey plug that I need to take off in between the bottom of the light and bumper but have no clue how to get to it..and what is the bulb number?
View 8 Replies