Ford Super Duty (1999-2016) :: 2015 F250 - Installation Of Upfitter Switches
Feb 21, 2015
I just got a 15 f250 with the console and nav system but it didn't come with the upfitter switches.
I picked these up and got a copy of the .pdf for the installation, but I'm finding it hard to follow for where the relay and box should install. I ran the wire up to the upfitter switch location and can even find a nice spot to connect the grounding wire.
I can't for the life of me figure out where the box installs and where the wiring harness taps into the main harness. Need a photo of where your box is installed and where it taps into the main harness?
View 6 Replies
Advertisement
How hard is it to install the upfitter switches and the fog lights? Is it all plug and play?
View 4 Replies
I want to install a set of upfitter switches but my truck didn't come with them...so I bought the switches and the relay/wire harness as well...I cannot find any good information on where to mount the relay and where an extra plug on that harness goes too. I have found the wires that attach and go through the firewall but I am not sure where the rest of this mess goes...my truck did not come with the wire harness already installed...
View 4 Replies
I have a 2010 F250 and wanted to power a dash camera using the upfitter switches. I purchased a 12volt wire, but am unsure on where to wire it so that it will only power up when the ignition is on..
View 7 Replies
I would like to do the high idle mod with my 2006 F-350 using the upfitter switches. I've seen a couple of threads about this but they are not real clear to me and don't mention the 2006.
View 14 Replies
First tech post for my new truck. I just bought a hold-over but new 2015 F250 XL Supercab 2wd and love the simplicity of no unwanted options. That said, there are two features I am adding. The first is perfectly straightforward, cruise control (swap button cluster and have the function turned on by the dealer). The second is a tiny bit more involved, back-up camera, in mirror display with bluetooth hands-free (I like the simple AM/FM radio because I can work it all with gloves on).
So I basically need three things from the truck and my research has been inconclusive on a couple of things because most of the threads are for 2014 or earlier. I think I can pull switched 12V and ground (pin 1 and 4) plus reverse lights (center, or pin 7) all from the the trailer wiring harness. It appears these are not affected by the canbus load restrictions of other places to tap reverse signal (remember, XL so likely nothing in the overhead console for the auto-dimming rear view mirror). Are there any challenges with this when I do hook up my enclosed trailer or when it is not hooked up regarding the trailer brake controller/anti-sway?
I already found a good youtube video for how to route the wires so I think this is my primary challenge at this point.
View 14 Replies
Where the blunt ends are for the Aux Switches. The manual says they are behind the passenger kick panel but I'll be danged if I can find them there. Are there none on the driver side?
View 9 Replies
My 2005 F250 just had the cab off in December for head studs and gaskets. Its a Crew Cab short bed FX4 so it has ESOF. When I engage 4x4 the blower will switch from blowing air out of the vents to blowing air out of the windshield defrost. Is a vacuum line plugged in wrong somewhere, or is one cracked? Trying to figure this out, its rather annoying
View 2 Replies
My 1999 F 250 5.4 liter. I know I have a vacuum leak because whenever I accelerate the air conditioning coming from the vents switches to the defroster. So my question is how do I go about finding the leak? My hubs in the front are manual so I know I don't have lines going up there. I do have some mechanical capabilities I've changed water pumps alternators brakes etc. But never anything with vacuum lines or a/c.
View 14 Replies
2015 KR. want to install a high idle kit controlled by an upfitter. If I remote start the truck with the upfitter left on, will that switch be powered while the truck is remote started, activating my high idle?
View 4 Replies
My elderly neighbor has asked me to re-attach his drive shaft on his F250.
Said his wife was driving and it broke the u joint or something, and he has gotten it repaired and wondered if I could put it back on. Has been sitting for a bit from what he said.
Just need to know, how I should clean up and or grease? the end with the boot on it. before I put it together. The boot looks to be zap strapped, is that standard?
View 2 Replies
I currently have Aux2 hooked up to my on-board compressor and it works like a charm...so I'd like to think I know how the wiring works for the upfitters haha.
This weekend I installed an electronic solenoid valve for my slip-tank so I can fuel up on the go. The valve is 110V AC and had two wiring leads of the same color so I assumed either/or could be used for power and the other for ground. I wired it all up running a power lead from Aux3 back to the valve and grounded the other wire to the body. To my surprise...no power! Can a 110V AC valve not be used in this application or is my wiring simply messed up/not making contact?
View 2 Replies
The lights are on on the switches themselves, I used the red pass through wire under the hood and then connected it to the Orange w/ blue tracer upfitter wire( I think #4 switch) and it has no power. Changed the fuse and still nothing??
View 13 Replies
I've checked the fuses, the lights are on on the switches, but I have no power at the wires under the hood. I'm adding lights and would like to use those switches..
View 2 Replies
Recently purchased a 2013 F350 w/upfitters. Figured Ford would have made access to the stubs easier by now (previous was an 05 6.0 ) and of course not. A bit more challenging. What parts of the dash do I attack and how. As the dealer is willing to charge only 40 bucks to connect any wires I run to the vicinity, I figure there's a slam dunk sequence for access.
View 7 Replies
This has been beaten to death but all the old threads I read are for 2011 to present SDs so I wanted to make sure I can add these to my 2008 before I spend $ on the switches. Anything I should look out for on the install? Once they are installed I would like to add front and rear strobes along with a roof light for plowing.
View 3 Replies
I've got a 2015 F250 with a 6.2 Liter with no compression on 3 cylinders. The dealer just diagnosed it and has not opened it up yet but the mechanic says it is probably a broken valve spring...that it is not uncommon in this engine.
My concern is not repairing the spring my concern is what a "free spinning" piston in 3 cylinders does to the life expectancy of the main and connecting bearings in this engine. I have rebuilt engines in the past and I have bought re-built from auto parts stores and from Jasper and I have never had any last more than 60-70K miles. It seems to me that even with very little mileage on the engine with three of eight pistons jumping around under no pressure that there could be considerable scarring of the bearings or bearing surfaces. I am no expert by any stretch but this is an engine in atruck that has less than 22K miles on it and I ain't real happy about opening it up let alone trusting for the next 280K miles that the bearings have more wear on them than they should have. It was only driven about 20 miles total like this but that is a lot of pressure on a highly tuned and pretty darn precision machine.
This is the newest vehicle I have owned since 1988 and I meant for it to be the last pickup I drive (I drive 'em til the wheels fall off) but I am not overly confident that even if this is a one off problem that it hasn't caused even more damage that won't show up for another 100K miles or so???
View 6 Replies
I have a 15 F250 CC SB 6.2 4x4 that is suffering from a driveline vibration. Had the shaft checked for balance and it was off. It's a little better now but still there. Checked all the angles and they're correct. Also came up with a curious observation that all CC SB 4x4's have a slip yoke driveshaft at the transfer case while all the other trucks have the fixed yoke. This appears to be my source of the vibration.
View 3 Replies
I have the ford upfitter switches in my 07 f350 and i had two flashing lights wired to switch 4 (10 amps) for snow plowing. The lights were LED and shouldn't have drawn much power but suddenly the lights stopped working because thers no power going to the fourth switch. They work on all the other switches. What could be the problem?
View 5 Replies
Sure would be convenient when hauling the 5er.
View 14 Replies
I have a 2015 F250 with a 6.2L and want to clean my throttle body. I have done several before on other vehicles but, just figured I would ask before I just jump in there. Cleaning throttle body on their 6.2L?
View 5 Replies
