Ford Super Duty (1999-2016) :: 22K With Hubs In Locked Position
Apr 3, 2017
Its a 2016 F-250, 6.2L gas truck with the electronic shift on the fly transfer case.
I have put right at 22,000 miles on it like this, frequently at 70-80 mph.
What are the odds I have damaged it and is there anything I should do now that I discovered it - other than put them both in "AUTO".
Truck has been to the dealer twice and not once was this noticed. They blamed the squealing on the brakes which I knew it wasn't.
View 14 Replies
Advertisement
Well long story short, I had the the factory hubs in my 04 f-350 and I was driving down the road and it started making this horrible popping noise. So I pulled over and couldn't find anything and just curiosity locked in the hubs and all was fine. Made me think my hubs were bad, so I went and bought the warren premium hubs, installed them. Went for a drive and still the same noise is there when they are in free spin. But once they are locked in its fine. What this could be? Wheel bearings?
View 4 Replies
But on my 2000 SD V10 the hubs are worn I just cant find which way to turn them to auto ?
I'm getting popping and such so I think I'm locked while turning.
Also.... IS there a way to check the COPS with a multimeter? I think I got a bad one.
View 1 Replies
Had to make a sharp circular turn last night in a parking lot, with the steering turned to full-lock...noticed a very audible clunking or clicking noise during the turn...went away after full-lock turning was released. My hubs are locked in...but I was told there was no issue with leaving them locked in, even during the summer. And there shouldn't be...4x4 disengaged, of course. Must have been the u-joints clicking / clunking? Problem?
View 5 Replies
Just got done with a ball joint replacement on my 2003 F550, everything went together great, just as it should. Until I got to the drivers side hub lock.
I have Mile Marker 449s/s manual hubs. Turn from free to lock and theres this loud clicking sound about halfway to LOCK (passenger side doesn't do this). Hub will stay locked for about 2 rotations, then it unlocks and makes a clicking sound. You cannot turn the hub back to FREE, it gets halfway and stops. I tried forcing it and broke the spring fingers inside. Have a new set on order.
Is this a locking hub issue or an assembly error? I was going to take these steps.
- Take passenger side hub lock off and see if it operates normally or same on drivers side.
- If same, remove axle and re-seat/re-assemble everything again
Anything to specifically check? All the parts went back in, washers were in correct order, outer snap ring is in groove.
View 11 Replies
Ok so some one locked my hubs and put the truck in 4x4 4low i assume my aunt was driving it, truck wouldn't shift from 2 to 3rd is this normal since its in 4low. The shifter also seems pretty stiff and 4wheel isn't used much if there a way to know if 3rd gear toon a crap? Trans fluid seems fine not dirty or burnt...
View 1 Replies
2008 F350 hubs wont stay locked in when in auto position. everything stays locked while in manual and 4x4 works fine, but in auto the hubs wont stay locked while spinning. I was trying to find the problem when i noticed that one hub stays locked all the time and the other locks and unlocks as it should but it wont stay locked while spinning. My question is do I have two bad hubs or is their a leak that wont let the hub stay locked? Also on the hub that wont unlock is this a leak problem as well or a internal problem?
View 5 Replies
Having an issue w/ my 00 550. When I lock in the hubs there is instantly a noise, More of a squealing then a grinding. The truck goes in and out of 4x4 no problem and the noise is there locked in 4x4 and not locked in, as long as the hubs are locked in. I can't tell if the noise is coming from the 4x4 driveshaft but there is no noticeable play in the u-joints or the u-joints in the front axle. I did notice when I spin the 4x4 shaft by hand the passenger side joint spins slower then the driver, not sure if that's normal or could be the problem.
View 2 Replies
We got a ton of snow dumped on us today and for some reason my 4WD has decided not to work this year. I have a 2000 F250 4WD Triton V10. The hubs click into the lock position and the dial on the dash lights up 4x4 but I am definitively not engaging into 4WD. I'm pissed because this is specifically the reason i bought a 4WD and it's failing me. I can't find a fuse panel diagram to save my life however all the fuses in the interior of truck look to be fine.
View 3 Replies
My son has a 2003 Super Duty with auto locks, but the front wheels won't lock even when turn to locked position. Also when it's in two wheel drive the front drive shaft and axles still spin, are the hubs locked up or is it in the transfer case?
View 10 Replies
Back in March while still plowing, my auto locking hubs wouldn't stay engaged. After talking to the local Ford service shop they told me that it was moisture in the vaccum lines and that it had frozen. They told me to manually lock the hubs and bring it in to be repaired when I had time. I made a appointment in the middle of May and finally got it in last week. Now the hubs are seized in the locked position and they will not warranty the work or parts because they say it was caused by the salt from our roads. Does this sound right?
View 5 Replies
I've read many posts about ESOF and fault vacuum lines and how that will prevent 4x4 from engaging. I experienced a different problem this past weekend. Here's the situation...
Was about 1.5hr drive up to the mountains. Outside temp when we left the house: 10F. Outside temp when we arrived at destination: 9F. Quite a bit of road grime on the way up from sand, slush, and that magnesium chloride (or whatever they hell they put on the roads in an attempt to keep it from freezing). 4x4 worked fine on the way up. 4x4 light on dash was on, and I KNOW I could not have climbed the snow-covered forest roads without being in 4x4. Also, I could hear and feel the front hubs turning.
On the way home, once I got to where the roads were sufficiently ice free, I turned the dial on the dash back to 2WD. 4x4 light goes out. But I can hear and feel the front hubs are still turning. Toggled the switch back and forth a few times. 4x4 light would come and go with the toggled switch. But the hubs didn't disengage.
When I got back into town (outside temp now about 5), we stopped at a red light and I toggled the switch again. This time, the hubs disengaged. Is this a sign of bad vacuum? Or more an indication of faulty hubs??
View 7 Replies
Is it ok to keep my front hubs locked in and the switch in the 2wd position for everyday driving? Only reason I do it is because in auto it doesn't always go into 4wd.
View 11 Replies
My hubs will not lock when put into 4x4. I disconnected all lines from the solenoid to both hubs and tested them for leaks... All good there. I put a gauge on the lines at both hubs one at a time while the other is still connected and get no reading when switched into 4x4. I checked for vacuum right out of the solenoid, and I get 2inHg when switched into 4x.
The vacuum pump kicks on every time I start the truck, even if I just shut it off and re-start right away. There is no delay when switching my ac/heater controls to different settings or vent locations. So I know there is vacuum. How much vacuum I should be getting out of the solenoid to the hubs?
2004 F350 6.0L....
View 3 Replies
I have a 01 f250 v10 4x4 ... My stock hubs squeak non stop when they are engaged. I want to get a set of warns.
I am going down to napa tomorrow, looking for a detailed link, or instructions of how to install these things? i have searched but just keep coming up with people raving about how great warn hubs are!
Do I need any special tools, do I need to grease the new ones before installing?
View 14 Replies
I just got a 99 F250 PSD, it had not been in 4wd in a while, now the hubs won't unlock.
My 01 F250 seemed to have strictly manual hubs. Turn right to lock, left to unlock. They may have been aftermarket, but on by the PO. Do I need to put some new Warns on the 99? Or can I lube then up and get them functional.
View 14 Replies
I just ordered '00 F250 SC 4x4 SWB XLT with the factory standard manual hubs. The hubs show up on the vehicle order confirmation as code "21M MAN LOCKING HUB". I can't find this code in the ordering guides anywhere but kbb.com shows this code as "Manual hubs delete. Required with 213 shift-on-the-fly". I want the manual hubs. I think ##### is incorrect. For my piece of mind, could someone who has also ordered the factory standard manual hubs verify that the code is indeed 21M. And for those who ordered shift-on-the-fly, could you verify that 21M does NOT show up on your order confirmation...
View 8 Replies
inside round thing with 4 notches in it is a smaller diameter than the new hubs. Will theystill work?
View 6 Replies
I am considering buying a 2001 Ford F250 Super Duty XLT 4x4 V10 engine tomorrow. I am hesitant because I cant get the 4x4 to engage. It goes into 4x4 low and high and the front driveshaft spins but it wont engage the wheels. One side locking hub locks but the other side the locking hub is cracked off and so I there is no way to turn to lock that side. I will of course replace the Locking Hub ASAP if I buy the rig but my question here is, if one side is locked should one side of the front axle spin, meaning if only one side Locking Hub is locked should that wheel turn and the other not? Both are not turning but as I said the driveshaft is spinning.
I don't know if both sides need to be locked in order for the front wheels to engage while in 4x4 high or low. Or if one side should engage if only one side is locked; the wheel that's locked of course..
2001 Ford F250 XLT Super Duty 4x4
V10 engine...
View 10 Replies
So after eight years my Warn premium hubs have taken a crap and developed major play internally. After speaking to Warn warrenty department and sending videos they will replace them according to the lifetime limited warranty. Problem is they sill not send out new ones until they receive the old ones, so I was told from time i remove mine and send them back and get the new ones it will be two weeks maybe a few days more, there is no snow in the extended forcast and im wondering what damage could occur with me funning the truck everday to work etc with the stub shafts just hanging there?
View 14 Replies
2006, ESOF. Noticed the front hubs aren't engaging but the transfer case is. What should I check?
View 3 Replies
