I know this is a common code and a common problem. I have had a buzz test and glow plug test done, no codes. Scanner code came up with P0275. I have read about injector change out, to O ring failure, to new EGR style. I have a 05, 6.0 SD SRW auto.
View 1 Replies2010 f250 cc 5.4 145000 miles. I bought it last fall have not drove it a lot. When using the cruise control and a load is added grade or hill in the roadway. It jerks hesitates or miss then cleans up and runs fine. When using the accelerator it does not do this. No codes.... Thinking about changing the plugs.
View 5 RepliesI have a E350 5.4 with 200,000 miles and it ran great before winter, this spring I fire it up and it got a miss I drive it anyway it starts to clear up and now the 1289 code. Everything looks fine coolant engine temp. I wonder if you can bypass the Cylinder Head Temp sensor. I am thinking the engine management is causing the miss to cool the engine.
View 3 RepliesI just purchased a 2003 F250 Super Duty with the 6.8L V10 It has really high miles on it as it was a landscaping companies fleet truck. I'm sure that it was pretty well serviced as it has 300K miles on it and it's still running pretty decent.
I picked up the truck and I have to get the smog done soon. It idles with what I can only describe as a slight miss and it runs and drives great. seems to have plenty of power for the miles that's on it.
There is no active CEL on but I scanned the OBDII system and found a P0171 Lean bank 1 code in the pending codes list of the scanner. I guess this year engine doesn't have an EGR Valve or DPFE sensor because I've looked high and low for it and there non existent on this engine.
I've checked for vacuum leaks by spraying brake cleaner or carb cleaner all over the place and it makes no difference and all the vacuum lines and connections look okay.
When it's running It does sound like a vacuum leak right behind the top of the plastic throttle body but I can't find it, I don't know if this big *** engine just sucks that much air or what.
Like I said I need to smog this thing soon and I don't want it to fail if it's missing or has another issue. The fuel injectors look new and one coil pack looks like it's a replacement...
Have an intermittent miss I can feel when driving 2006 F250 5.4 l 4x4 stick; Freeze frame from Cen-Tech 60794 (from Harbor Freight) scanner follows.
DTC CNT 0
DTC FRZF P 0352
FUEL SYS1 OL - FAULT?
FUEL SYS2 --
LOAD PCT 25.9
ELT (DEGREES F) 186
SHRTFT 1 0.0
[Code] ....
I can operate the scanner but what these ranges should be. What might be causing the miss? This scan shows 951 rpm, I was idling along in 1st in traffic, but I have also felt the miss at 75-80 mph (about 2300 rpm) on the Interstate and at other times, with light loads in the 1500- 2000 range in town.
My 5.4 had a bad miss several months back with no cel. It would barely climb hills it never even needed extra throttle on before (3rd gear, wide open, 35 mph, etc). Ford dealer ran a scan and it had two bad coils and plugs. I changed those and it ran much better, but still had a "pfft pfft" exhaust leak type sound at idle. I checked the exhaust studs and they were all good, so I wrote it off as just a normal exhaust leak.
Full throttle in 5th gear to maintain speed limit when normal throttle before was sufficient. I got home and parked it and it sat over night. I went to start it today and it died. Tried again, died again. It only stays running if I am pressing the gas and I hear a fluttering or air sound of some kind coming from the passenger's side of the engine. It doesn't cut out or miss like a bad coil or plugs, but like you choked off the air supply.
All plugs are still in place, exhaust studs look good, tried it with the air box unhooked to see if it got clogged, and going to check intake leak tomorrow...
Having problems with 1999 or later 7.3 missing or dying when you turn on the wiper switch?
View 8 RepliesI recently had a thread going regarding my 1999 F350 2wd auto transmission slipping in/out gear. Tried to follow up on old thread but got confused so I'm trying to start a new one. Basic problem is that truck was slipping in/out of gear. Cleaned the solenoid pack electrical plug (as instructed on previous thread) and the truck didn't act up for 2 weeks. Today it started slipping in/out again and this time it registered a code of P0705.
View 7 RepliesGot a 2001 F350 diesel auto, 295k miles.
It has miss when over 2000rpm. Below 2000 its smooth.
ICP has oil in sensor, ordered new one. Gonna change oil too.
CPS is new (not sure if its black or the other one). Starts idles and drives good otherwise.
Where should I look?
It's a 1999 f250sd 5.4l auto. Has code p1747. Truck shudders and almost dies when you drop it in gear, put it back in park idles fine. I have read all the post on here about this and checked wires from trans up to pcm look and test well. Tested plug c1048 wires with the digital meter to body ground with battery unhooked and got 6.66k ohms on pin 11 circuit 925, 421 ohms pins 1 and 12. Plugged c1048 back to trans checked 925 w/y wire at plug c103 got 9.1 ohms back to trans. Is the EPC solenoid bad or is it pcm? I think its epc but want to verify before i take trans apart.
View 2 RepliesIts a 1999 f250sd 5.4l auto. Has code p1747. Truck shudders and almost dies when you drop it in gear, put it back in park idles fine. I have read all the post on here about this and checked wires from trans up to pcm look and test good. Tested plug c1048 wires with digital meter to body ground with battery unhooked and got 6.66k ohms on pin 11 circuit 925, 421 ohms pins 1 and 12. Plugged c1048 back to trans checked 925 w/y wire at plug c103 got 9.1 ohms back to trans. Is the epc solenoid bad or is it pcm. I think its epc but want to verify before i take trans apart.
View 3 RepliesI have a 2000 F350 cab and chassis 4X4 with V10 and a 5 speed manual (actually it's a 4 speed with overdrive). My problem is the engine seems to have a miss in it. When I first start it in the morning it usually runs good for 5+ miles till it warms up then if I am not pulling a load I can hear what sounds like a miss but the truck accelerates fine. If I am pulling a load I can also feel a slight steady consistent shudder and I can tell the truck doesn't have the power it should and the gas mileage SUCKS worse than it use to.
I ran a bottle of Lucas deep clean through a tank of fuel and that seemed to work a little but I will still encounter the problem sometime during the day. When the miss seems to be gone I can hear a very slight pinging noise when I accelerate or pull a hill with and/or with out a load. The pinging noise I hear sounds like an engine with a distributor that is getting to much spark advance if you have ever experienced that before.
I purchased this truck used several years ago and I don't know what the PO did but the check engine light is not coming on and it doesn't throw a code. I put 10 new ford coil packs on it about a year ago so I really don't think it's a coil pack, but I could be wrong. To me it sounds like maybe it an injector problem????? I know there are several sensors on this engine and I am thinking maybe a crank position sensor is not working right but I honestly don't know???? Is there a way to test this sensor?
I have a 2000 F-250 V10 that misses (cylinder 10) at the idle, once you give it gas it runs correctly again. I am at a loss. I have replaced the plug, tried moving coils from one cylinder to another to see if it shifts the miss, and it has new injectors. What this could be?
View 9 RepliesI have been having trouble with my 2008 Ford F250 4x4, 6.4 liter diesel transmission. SCT tuner, 10" lift, egg delete and dp delete has been done. I have been losing power mainly in reverse but have noticed that the transmission hasn't always been going into the last gear on the interstate. Code PO741 would come up. The other day the shifter was stuck. So I played with it and found that the cable on the transmission had fallen off. After replacing it. The transmission wouldn't go into reverse but has been doing semi good in forward. Well I have been limping it around until today when I was going down the road and it completely stopped pulling. Now no matter what gear I place it in, it will on go in reverse. What could be causing these issues or where to even begin to start looking?
View 3 RepliesI have a 2003 f250 5.4 with a couple of bad valves and low compression and a dead miss because of it... I just bought what appears to be a 2001 5.4 from an f150... I am worried now this engine wont work and cannot find anything online that can tell me yes or no....
View 12 RepliesQuestion, my truck started to have a miss under normal acceleration, when I really get on it, it clears up? I also noticed a bad sulfer smell at idle. Im thinking the cat is possibly plugged? Truck had 172000ish on it, and the cat is original. I did do a big tune up this past fall, new plugs, coil packs, air and fuel filter. Should I put a new cat on it? And a new oxygen sensor?
View 9 RepliesThis last April I was towing my trailer back from camping approx 125 miles when I detected a loss of power and a slight miss. I managed to make it home. It wasn't until I made it home that the engine finally started coding. Miss on start, a couple of cylinders missing and output shaft speed sensor circuit failure. So naturally, I decided to do what I felt needed done anyways, change all coils and plugs. Oddly the problem got worse to the point where I almost didn't make it home after test driving it, it kept stalling out and was difficult to keep running.
After some research and advice from others, I started replacing some components; MAF sensor,IAC valve, output shaft speed sensor. Nothing. In fact now the truck wont move, I start it up it idles a little rough, but then I put it into gear and with in seconds she shuts her self down. I've replaced the fuel filter, checked the fuel pressure and it is in specs. I've now had it towed to two mechanics neither of which have any solution. They've put expensive computers up to it and still nothing. I really do not know what to do at this point. Lastly the only code that continues to come up is P0720, output shaft speed sensor circuit failure, I really miss my truck!
I got an f-350 drw it is sluggish on take off feels like a miss. Higher speeds when you step on it. It seems o.k I have been told it could be a crank shaft positioning sensor any in put on this. I have changed the fuel filters, cleaned the e.g.r. valve and yes it was pretty clogged,air filter seems to be good. And 1 last thing for now where would c.s.p.s. be located...
View 4 RepliesOn a 2000 F-350 with 5.4 engine, where does the vacuum line enter the cab? I got a truck in with no vacuum signal to the heat controls, and it has a slight miss at idle. Both of these are signs of a vacuum leak, but i can not find the line going into the cab.
View 5 RepliesDid a 1600 mile trip and noticed that the cruise 2x would just shut off. Most of the time tho it ran fine. Every once in a while when I would stop for gas and turn off the motor the cruise would not come on at all when we headed back out. Sometimes when it did this it would not come back on till I shut off the truck and then restart. Other times it would work after 20 or so miles.
When it did shut off or not come on, I would try turning it on and off, mashing the buttons HARD, What to do? Or should I just take it to the dealer and be done with it?
02 E450 Super Duty V10, C class a motorhome, 29000 miles. Cruise stopped working a month or so back. I searched this forum and managed to fix it with the info provided. It turned out to be the pressure switch on the master cylinder, the recall had been done. I replaced the pressure switch and the harness with an aftermarket one from the local auto parts store. It worked well for about 200 miles, it knocked off again on our road trip last week. It was working on the road and we stopped for breakfast and it didn't come on again, no light in the dash or anything.
When I ran the internal diagnostics on the first repair all the lights would flash when the buttons were pressed and the servo would cycle through at the end of the test as it should, based on the diagnostic instructions. This time when I run the diagnostic test the light will flash when I first turn the switch on (holding the off button down) and when I push the on the button but will not flash when I press the other 3 buttons.
I have not been able to find a wiring diagram for this particular truck, I've found 6 or so but none of them match my fuse boxes under the hood and dash.
I have no trouble lights on in the dash CEL or ABS. I'm at a loss what direction to take from here.