Ford Super Duty (1999-2016) :: F350 Engine Temp Started To Increase - Code P1212 For ICP
Aug 13, 2013
1999 F350 SD ... Yesterday when goosin it to get on the highway my rig threw up a code quickly and engine temp started to increase. Once temp got in the red, oil pressure got a little figgity. The code was for the ICP(p1212), so I cleaned the plug and made sure coolant and oil were topped. This morning she ran barely over normal temp (stock gauge). This afternoon same thing as yesterday but without the code. When I let off of the accelerator temp goes down. I just got married so I have little funds to throw at a shop.
View 4 Replies
Advertisement
I have an '06 F350 dually with a 6.0 diesel. I bought this used about 5 years ago and for the most part have loved it. i would always smile on the inside when i heard people bash the 6.0...i thought i got lucky....until today.
140k miles. recent oil change. all is swell...until this morning. Stick in key and turn it. glow plug indicator comes on...all lights come on for a few second....wrench, abs, dtc etc....wrench shuts off...glow plug light comes on...4 or 5 seconds later wrench light comes back on....turn key and NO CRANK.
All fuses are fine...starter cranks if i jump the solenoid...but it won't start. Miles to empty and everything else is just dashes hit the OBD and it says "engine sensor data error"/ "trans temp error" ...
View 1 Replies
My truck threw a code p1299 last night on my way home from the lake. I was towing on a huge grade and all the sudden my engine temp gauge pegged out on me and check engine light came on. I pulled over and noticed a bunch of coolant had overflown the cap but the engine didn't seem to have over heated. When I restarted the truck the engine temp was immediately normal range. I drove for another 30 min or so and the engine temp started to climb and then come back to normal then climb and stay pegged. I pulled over again and noticed the coolant level was low and coolant had overflown the reservoir. I restarted the truck and once again it was normal. I just drove surface streets the rest of the way with no issue. I suspect blown head gasket. This is a 2003 F-250 6.8L with 100000 miles.
View 8 Replies
Replaced HPFP 38,000 miles ago. Truck began going in limp mode without engine light, wrench came on in dash, gave codes for brake switch, anti-theft, some other weird codes. Had those codes cleared, ran for while then water separator came on, drained the water out, came back on. Read some forums, so I removed and cleaned the housing, cleaned off the sensor. Had code cleared and ran good for about a week. Then guess what engine light comes on, limp mode.
Went to Auto Zone, pulled code P0088. This truck runs awesome until limp mode. No other problems. I take it to the ford dealer, scanner pulled P0088 and the water separator code again. I have read alot of remarks about this P0088 code. Can there be another cause for pulling this code, only 38,000 miles later. I had them do the TSB 12-07-07 but I have also read it can only be done if the P0088 is the only code. I just really feel there is an underlying issue with these 6.4's.
View 3 Replies
What are my options for increasing the engine power in my truck? I'd like to see somewhere between 350-450 hp on the rear wheels. Unlike you guys in USA I can't just drop my truck of at any garage and pay them to do this for me as i live in northern Norway and there ar as good as none who work or knows much about american trucks here. I also wonder what power levels can the original transmission handle whiteout reinforcement?
View 14 Replies
I have a 2001 F350 and the temp read-out on the mirror hasn't worked since I got the truck in 2004. Where the sensor is. I found a connector on the back side the core support on the driver's side that has nothing plugged in. Could this be where it should be?
View 4 Replies
I had a mechanic replace the temp sensor on the top of the intake in my 2001 f350 v10 and since then my temp gauge doesn't work. He replaced the sensor again and still nothing. Is there a different sensor/sender that controls the temp gauge???
View 4 Replies
2007 f350. About 2 weeks ago my truck started smoking really bad, and I took it in to have it diagnosed. It was 4 injectors that were bad, so I had them replace all 8 and also install a bullet proof oil cooler. From the moment I got the truck back, it did not seem to idle as well as it used to, and over the next week, it began to blow a good amount of white smoke and run very rough.
But the weird thing is when I took it back to the shop to have it diagnosed, the minute I pulled into their driveway, it ran perfect, and they were unable to pull up anything. The next morning, I started my truck for work and as I drove down the street, the truck ran extremely rough, and seemed to be running in 2 cylinders. I shut the truck down, restarted it and it ran a little better, as I limped it back to the shop.
View 6 Replies
The trans temp guage on my '08 F-350. V-10 started acting erratically, and the wrench icon popped up on the display. i crawled under the truck to look for the sending unit and it's lead. i assume that i found the lead. it is encased in a corrugated sleeve, and appears to be a vaccuum type tube and boot connector? the boot still had a small round gray cap plugged into it. it appears that the cap was never glued (go figure) upon assembly. i have tried to reach up on top of the trans to find the sending unit to figure out the best angle of attack. i can barely touch it with the tip of my finger. going with mechanical guages is out of the question at the moment, so i'm wondering can it be driven any distance this way, AND any schmooze tricks developed to get at the sucker without dropping the cross member or exhaust????
View 3 Replies
I have an isspro sensor that I need to install on my 4r100. I have it all installed except for the actual sending unit. My question is where is the best place to put it?
I've watched multiple YouTube videos and it seems a lot of people use the test port on the driver side above the linkage. I found out the hard way that it is a very poor choice of location. A lot of people say that the best way is to drop the pan drill a hole and weld in the bung? I was wondering would it be possible to put it on the "out" line on the transmission oil headed to the cooler? 01 f-350 7.3
View 4 Replies
I replaced the sensor on top of the water pump and the gauge still doesn't work. I tested the gauge by unplugging and grounding out the wire and the gauge goes all the way up. What I can try next. I didn't get a Motorcraft sensor so I'm going to go get one of those tomorrow hoping the duralast wasn't correct even though it looked 98 percent identical to the original. 7.3 lite diesel.
View 1 Replies
So I went to start the truck this morning around 8:00 and it was 7 degrees outside, when the truck started the oil light came on and oil gauge was on low? So I turned it off right away. few hours later I tried it again and still nothing I thought maybe the oil was frozen. After I started the truck the oil was higher on the dipstick so I am assuming the oil pump is functional. What could be causing this? Could it be the the gauge is not working? The truck is a 2000 F-350 V-8 5.4 gas. I'm hoping it is something simple I am suppose to work this afternoon
View 14 Replies
Tried changing fuel filters on my 2008 F350 diesel. Tried primary - open drain - no tool to remove cap, closed drain. Removed top cap, replaced filter.
Started but immediately shut down. Did this twice. Put old filter back in - still no start. Wrench code light on.
View 9 Replies
I bought a 1999 f350 v10 about a month ago took it on a 1200 mile trip from Arizona to Kansas. Truck ran great till I got Kansas. The truck started to lope after I got fuel at a fuel station. Did not get any check engine light on. I check for vacuum leaks did not find any. I change all the coil packs, spark plugs, IAC valve and fuel filter. Clean the intake and put sea foam in the fuel tank and the truck still idles rough. Change the egr vavle. Truck ran great till I got 10 miles down the road then the truck started to lope again. So I'm getting really frustrated over this truck.
View 4 Replies
2004 f350 lariat Key fob slowly started not to work until it finally quit. Thought it was the battery but changing it had no change. Do the fobs go bad and need to be replaced?
View 11 Replies
I have a 2005 F 350 with a 6.0 Diesel! My heat quit on my wife and I the other night! I replaced some fuses and started the truck to make sure the heat was working and it was! So I thought while I am here I should replace some bulbs in the cluster that were out!
I took the cluster out, looked at the bulbs and they looked oK so I put them back in and put the dash back together! When I went to start the truck once I turned the switch on my gauges and lights started flickering on and off fast and all it will do is just click when I try to start it! I just had it running 15 minutes before this!
I went through all the fuses and if I take one of the relays out and turn the switch on all the lights and gauges seem to work right but when I try to start it, nothing! I replaced the relay and it starts flickering again! I had the relay checked at Napa and they said it was good! The relay was for the Powertrain module!
View 2 Replies
I have a 2006 F350 SRW 4WD 6.0 with 127000 miles on it. A couple of weeks ago it, pulling out of my driveway, it hesitated and tow haul started flashing. I had codes pulled and it showed P1780, P0751, and P2700. After turning off, codes were gone and tow haul off. Ran fine since then every day. Yesterday while going about 50 mph it started acting like it was in neutral (revving up), nothing happened when mashing the accelerator. Coasted to a driveway and truck would not move, only sounded like it was in neutral.
View 1 Replies
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 Replies
2010 F350 in my shop today. so, before dismantling the entire top of the motor for this inbred oil cooler job, is there anything else responsible for the P012 engine oil temp issue? it throws the wrench icon and cuts power and i pulled the P012F code.
View 9 Replies
Just picked up new 2014 F350 lariat today and I can't figure out how to change the keypad code. I enter the factory code and hit add, but when I enter a new 5 digit code it wont let me hit enter.
View 2 Replies
I was driving from home to work the other day and it was 6 degrees out. My heat was working good and everything was fine and then all of a sudden the passenger side started blowing cool air. Not cold not warm. Driver side was still hot. It is a lariat and has dual temp zones. Everything I read everyone says blender doors but what would make it stop working out of no where when everything was fine. Occasionally when I start my truck and turn the heat on it makes a popping noise under the dash when the blower kicks on. But it has done this since I owned it an never had an issue. It's 25 below today and I would really love to have completely functional heat. It's an 2008 f350.
View 14 Replies
