Ford Super Duty (1999-2016) :: Pin Fell Out Of Automatic Trans Gear Selector
May 14, 2014
The other day I had a metal pin fall out from under my dash and hit me on the foot (only reason I would have know if fell out till I clean the truck)
Ever since then the gear selector handle for my transmission has become sloppy and when I go to turn off the truck, I have to hold the arm up to turn key off all the way. I have looked to try and find where it goes and cannot find the location. I have also looked at a blown up parts diagram and cannot find it. Where it goes?
2002 F250 SD V10 with auto...
View 1 Replies
Advertisement
Whenever I manually pull my gear selector into first gear it blows one of the 10a fuses (not sure which number). I lose all gauges and accelerator pedal. It's about the fourth fuse from the right on the bottom row.
View 4 Replies
The switch for turning overdrive off that's located on the auto trans shifter stopped working. I've taken off the column cover to see if the wires have been severed from the tilt wheel, but nothing wrong there. I also checked the fuses, and all is well. Is it possible that the switch is bad at the end of the shifter, or somewhere farther down the column?
View 14 Replies
My tranny only goes to 3rd gear in 4x4 lo is that normal? 2014 6.2 xl f250 ....
View 14 Replies
I have a H&S mini max. Controller and have installed the mild download and run on the street setting for every day and tow setting while towing my fithwheel, when I just took it out for a test drive towing the fit wheel going up hill it kept shifting up and down which sure felt like 3rd and 5th because rpm would go from about 3500 to 1500 back and forth so it sure felt like it was not hitting 4th, could this be a controller issue?
View 4 Replies
So when I try to kick into 'passing gear' in this '01 f250 5.4l, i get no tranny shift. Whether I'm in tow/haul mode or not.
View 10 Replies
I recently purchased a 04 f250 with the 6.0l powerstroke. I drove it for about 3 weeks now, Ive put my trailer behind it with small loads and just today tried to use the tow/haul button. When you go to pull out the tranny never shifts from first gear?? Its pulls and runs fine until you push the buttan and no shifting........
View 6 Replies
I have a 99 f250 with some procomp (325s) that are 12.5 wide with a 6in lift my superchip tuner can change the trannys shift points but I am pretty sure a new gear ratio is needed. I dont do a whole lot of off roading with it its mainly my driving around and highway rig whats a good gear ratio that would work for me
View 9 Replies
I have a 2014 f250 with the 6.2 and just turned 13,800 miles. I tend to drive in tow haul a lot, while not towing because I like the shift pattern better and saves on brakes while stopping. Last night I slowed to a stop sign, came to complete stop. Went to take off slowly like always and the truck was like in neutral, looked down and the indicator showed 5th gear. Let off and watched it go to 1st and took off no problem. This all took only half a second or so, seemed fine after that. What might of happened?
View 3 Replies
Bad news: Radiator fan fell off while driving tore up fan blades. It is going to take them a week to get the parts!
Good news: My extended warranty is good for 10 more days! So the fan and fan clutch need replaced.
Should I insist that they replace the serpentine belt that rubbed on fan (50,000 miles on belt, original belt) and the water pump? It put a good dent in the radiator but didn't puncture it.
View 14 Replies
My Bump Stops have completely dry rotted and fell off the truck. I have an 08 with a 2 inch leveling kit, I already did all the body bushings, as they disintegrated as well. Should I bother replacing them? I highly doubt that I would ever bottom out that bad that I would need them?
If I should replace them, then where did u guy's get them and should I go with the Neoprene like I did with the body bushings?
[URL]
View 9 Replies
My 6.0 lost a bolt that holds the AC clutch and the clutch fell off. It's probably on some highway making people have flats. Is it possible to buy a replacement clutch and NOT remove the OEM pulley, just take the parts off the replacement clutch and put them on the old AC and existing pulley?
View 9 Replies
My automatic shift selector was extremely loose. Wasn't the two bolts up behind the dash. Turns out that there is a metal cylinder with a cutaway that seems to have fallen out of the selector housing. One of the edges of this cylinder broke off as you can see in this pic:
What is this piece called and can I get a replacement at autozone/pepboys/ect?
View 10 Replies
I have a 2006 F250 and the other morning I came out and found the rear view mirror laying on the cab floor. No biggie, I'll just glue it back on. Then I noticed the small black decal looking thing on the inside of the windshield. My question is, does this have to come off in order to re-install the mirror with standard Permatex mirror adhesive, or do I just put adhesive on top of it? Also, is there a different, specific adhesive used here that won't crack the windshield 2 weeks from now, like I read. Took a closer look and realized they used a thin adhesive patch to attach the mirror. I'll get one from the dealer.
View 3 Replies
After reading the book, I'm afraid I still don't understand. When the hubs are in AUTO, & the shift on the fly selector is turned to 4X4 high, or 4X4 low, is the truck in 4 wheel drive. What happened to free or lock.
View 3 Replies
I pulled into my driveway after a 30 minute drive and smelled burning brakes. The right front was the culprit so I took a garden hose and cooled it down. The next day I remove the caliper and one of the pistons fell apart. So I need a new caliper and trying to decide if I buy after market or go with Motorcraft? I think the rotor, caliper, and pads are original since I the rotor is stamped Ford and the caliper bracket has TRW and Ford markings.
View 12 Replies
Today I either broke timing chain or it fell off on the passenger side bank of my 08 F250 V10. Put a hole in valve cover. What to expect for repairs. Is this engine Zero tolerance.. unsure if I should expect bent valves or not and just how far I may have to go with this.. best way to test. I have a bore scope camera and mechanical abilities.
View 14 Replies
I have a 2016 F350 Lariat. I feel the auto headlights do not come on soon enough. I have not talked to Ford yet, but am wondering if there is a way to adjust when the auto lights come on?
View 8 Replies
2006 350 here. I was wondering if it would be possible to replace my Automatic tranny shift lever with one from a newer truck (08+). If possible, what exactly would need to be replaced?
View 1 Replies
A few weeks ago I noticed what seemed like a "slip" in my automatic transmission. Only happened a couple of times and I thought maybe it was just me imagining it or I didn't have the shift selector lever firmly in "D"rive. Then I went on a 4,000 mile trip pulling about 3,500 lbs. on mostly flat roads but it did include some 7% grades in the hilly parts... the truck performed flawlessly.
This is probably not related but ... after I got home, the truck sat for a few days and then I noticed a coolant puddle under the truck. Traced it down to what appeared to be a slow drip from a bad squeeze clamp on the large, lower rad hose connection. Replaced the squeeze clamp with 2 worm drive clamps and no leaking issue since.
Then last night, the tranny seemed to "slip". My short run across town started out OK. However, when I arrived at my destination, the diesel motor would rev to around 2500 rpm but the truck barely moved forward. It eventually did shift into second but also with high revs. It was the same feeling as if it were a manual tranny and you were giving it lots of throttle but only letting out the clutch a little bit (i.e. riding the clutch). This happened a couple of times last night. Also at a stoplight with the brakes on firmly, the truck was gently and rhythmically "rocking forward" as if the tranny was not fully disengaged.
When I worked through the gears shifting manually, the problem seemed to disappear and the truck responded going through the gears normally. Upon restart about an hour later, tranny shifted fine both in the city and at highways speeds on the way home.
B-I-L commented "sounds like your clutch is slipping". Not exactly sure what he meant as I had to leave. I'm hoping this will be a simple fix/adjustment and not the dreaded mechanical diode failure leading to a replacement tranny. Truck only has about 75,000 miles on it.
I'm suppose to head out on my annual vacation next week carrying a 3,500 lbs. truck camper and pulling a 3,000 lbs. cargo trailer with our gear. Obviously if the truck is sick, this trip can't happen. I know some of you would dive right in and start taking the tranny apart to repair it ... What is wrong with my transmission and what I should be doing next?
View 10 Replies
I love the power folding mirrors on my 2014 F250 Lariat, really makes a difference in parking lots. Is it possible to make them fold automatically when turning off the vehicle? I know it is a lazy person question but with automatic seats and mirror/peddle position wouldn't automatic folding also be a good idea?
View 4 Replies
