Ford Super Duty (1999-2016) :: Service Engine Soon Light On - Codes P0171 And 0174?
Mar 26, 2013
I have a 1999 Ford V-10 Triton 6.8L engine with 100,000 miles in my Motorhome. Service engine soon light has been a problem for the past couple months. I have replaced the O2 sensor on the passenger side and the EGR valve. After that I drove for about 300+ miles continuously and stopped to get gas. Light stayed off and I thought I had it fixed but after starting up again the light came back on. The codes are P0171 and 0174.
I had the air filter replaced before changing the sensor and valve and mechanic left the Mass air flow sensor out of the socket I had a sluggish engine and at the time I thought I sucked water into the filter, I was driving in a pouring rain, this sensor plugs into the air intake above the filter correct?) I plugged that back in. What is my next move because I reset the service engine soon light and it runs great then the light comes back on after I shutdown and restart.
View 3 Replies
Advertisement
My 1999 F350 SD V10 that would crank but not start. I ended up checking numerous things because before it decided to truly stop running, it would run rough for a time and then be fine. The check Engine Light came on and I got the codes P0171 & P0174. Well, I bought MAF Cleaner and took the air cleaner housing off, disassembled it and thoroughly cleaned the sensor and replaced the air cleaner. I continued to get those same error codes, but before I could go any further, the truck totally died. It sat for nearly 2 months with the bed in the air as I had decided to lift the bed to check the fuel pump vs. drop the tank.
Fast forward a bit and I have since replaced the fuel pump and put $40 of Premium Gas along with Royal Purple Fuel Treatment in the tank because I figured things got stirred up and could use a bit of cleaning. I do not drive much, and during the first few trips, it ran perfectly. Then today, it started again with the rough running and trying to die if I let it idle. If I pushed on the gas, it would completely smooth out. If this were a carbureted engine, I would think the low idle was set too low, but since it is not, I am guessing it is one or more of the sensor/s that is/are causing the issue.
I am disabled and can’t play parts swap until I hit on the right part, so I was hoping that I might get some guidance here to narrow things down to the most probably causes so that I won’t go broke changing things until I hit the “right one”. The truck has 153,000 miles on it and I had bought it from a retired couple who used it to pull their 5th wheel travel trailer, so it had mostly highway miles on it. It was immaculate when I bought it and ran perfectly, needing only normal maintenance (oil changes, etc.) over the past 12 years that I have owned it. In those 12 years, I have put about 60,000 miles on it.
View 3 Replies
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
View 6 Replies
My 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
View 10 Replies
1999 F250 Super Duty. My service engine light came on while driving doing around 65 mph. Truck seems to be running normal, no loss of power or acceleration. It's a 5.4L with 104000.
View 6 Replies
2000 F250 V10 Auto/Rebuilt Tranny... This weekend, I noticed my truck wasn't shifting at lower RPMs like it has been. I'm not hitting much higher RPMs per shift then normal. Very soon after, I get a "Service Engine Soon" light and my "OD OFF" light on my shifter handle started flashing.
View 8 Replies
Have a an 11 f350 6.2 gas throwing p0171 and 0174. Driving the truck it has spark knock pretty bad. Ive parked it at this point. Its a tow truck so I need it fixed and back on the road. I've checked the hoses going to the pcvs they appear to be ok.... Also upon starting the truck it just sounds weak.....
View 1 Replies
I have a 2011 f250 with the 6.7l diesel. Overall it's been fabulous. Descent mileage, and never ending power. The service engine soon light came on the other day. I have checked the fuel and dropped some additive in the tank. Have also checked the air filter which is good. There is a hesitation when giving it throttle. Then it shoots like a rocket.
View 6 Replies
2001 f350 7.3 diesel and I come up with the codes for upper and lower dual generator fault. I have only one alternator not the dual.. I checked the gauge and it is running at 14 consistently. But the service engine soon light keeps coming on...I clear them and they come right back... Alternator is only 2 years old and not a rmf..
View 1 Replies
I've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.
My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.
My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.
I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.
Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.
I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?
Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?
View 14 Replies
I just bought a 2003 F250 from a used dealer. Unfortunately the service engine light keeps popping on and putting out the code P0401, I have replaced the EGR, cleaned the inside, and cleared the code. However it continues to keep popping up and then it will turn off after a couple of days. I mostly drive in the city and the code generally only pops on when I drive on the highway. I have also noticed a lack or delay of power, when I really hit it hard, I think its because the computer is keeping the egr valve open. What it could be?
View 3 Replies
2 weeks ago I had the check engine light come up on my 2011 F-250 6.2 XLT. Did a diagnostic check and Codes P2098 and P2272 came up. Did some research and found out the second O2 sensor on passenger side had gone bad. I replaced it with a Motorcraft O2 sensor and cleared the code. It has not came back since. But still not getting the fuel mileage I got before. What else could be wrong?
View 5 Replies
I own a 2011 F350 dually with the 6.7 in it. It has 136000 on it and zero mods. I was driving over the weekend and the traction control light, brake light, and the ABS lights all came on and the information center displayed Check Brake System. We were towing our 5th wheel when this happened. The brakes on the pickup and trailer both work and we have no problems stopping. About every 15 minutes or so this message pops up and it chimes again. My insight is reading a U0418 code. We are stopped now and the code and alert message is still popping up without the trailer. All fluid levels are where they should be.
We are also getting a check engine light and my Insight is reading the codes P2020 and P20E8.
I can reset the codes dealing with the reductant leakage and low pressure, but not the codes dealing with the brake system.
I have had my pickup in to 2 different ford dealers for these issues and they cannot find anything wrong. I did notice that this time when the Check Brake system warning appeared that the pick up started lunging a bit, we lost power to the stereo and the windshield wipers came on. Our fuel mileage has remained the same and the pickup still tows like a beast.
View 1 Replies
Problems my truck seems to be having for one thing sometimes when I'm going thru the gears (6 speed manual) the truck won't wind up all the way it's like it is rev limiting at about 2000 RPMS, been doing that for a while , it does that most of the time but not always. Problem #2 the anti lock lite stays on in the cluster, and just yesterday the service engine soon lite is now on, my truck is a 1999 F250 7.3 6speed manual with 77000 miles on it ...
View 1 Replies
I have a 99 F450. I have an ABS light on. No codes (at least not that my code reader can pickup), but I am also not having any issues. Brakes work fine. What to swap out or where to look?
View 7 Replies
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
View 2 Replies
The SES light in my 2001 7.3 came on about a month ago while I was towing a light trailer in the SoCal mountains. When I got home I spent about 2 weeks replacing the injector o-rings and glow plugs. I discovered while I was in there that the head bolts on the driver's side where loose. I retorqued them to spec.
Both batteries were disconnected for the 2 weeks. When I started the truck the SES light was still on.
My Torque Pro app isn't showing any error codes, and is reading live data correctly. (I didn't have the app when the light first came on; I only purchased it after I finished the repairs). Am I missing something? Is the SES light not necessarily connected to fault codes? If so, wouldn't it reset after 2 weeks with the batteries disconnected?
View 5 Replies
I just purchased a 2003 F250 Super Duty with the 6.8L V10 It has really high miles on it as it was a landscaping companies fleet truck. I'm sure that it was pretty well serviced as it has 300K miles on it and it's still running pretty decent.
I picked up the truck and I have to get the smog done soon. It idles with what I can only describe as a slight miss and it runs and drives great. seems to have plenty of power for the miles that's on it.
There is no active CEL on but I scanned the OBDII system and found a P0171 Lean bank 1 code in the pending codes list of the scanner. I guess this year engine doesn't have an EGR Valve or DPFE sensor because I've looked high and low for it and there non existent on this engine.
I've checked for vacuum leaks by spraying brake cleaner or carb cleaner all over the place and it makes no difference and all the vacuum lines and connections look okay.
When it's running It does sound like a vacuum leak right behind the top of the plastic throttle body but I can't find it, I don't know if this big *** engine just sucks that much air or what.
Like I said I need to smog this thing soon and I don't want it to fail if it's missing or has another issue. The fuel injectors look new and one coil pack looks like it's a replacement...
View 14 Replies
2002 F-250 5.4l 4x4 ... I am getting a P0171 code only, with strong fuel smell. No P0174 code. So it has to be something effecting just the one bank? Sprayed engine with starting fluid, no charge in idle. Replaced upstream O2 sensor, no change. Truck was running fine, and then just started this all at once.
View 5 Replies
I bought a 2004 excursion 4wd 6.0 EB Excursion a few weeks ago and I noticed it making clicking noises after I shut the engine off yesterday.
Its been throwing codes P0683 and P0404 intermittently. (they clear themselves after a day or so and dont reappear for another three or four days)
[URL] .....
View 5 Replies
I have a 97 F350 5.8 with E40D trans. I bought the truck with it shifting hard thinking maybe a simple filter/fluid change would fix it. It may have worked a little but did not fix the issue. There were 3 or 4 codes that I have already cleared up with new parts. I am still getting a 327 (something with EGR?) and 629 (Converter clutch control circuit failure). These show up in KOEO and KOER self test. The O/D does not flash ( bulb does work).
Parts that have been replaced: VSS, MLPS, new connector going into solenoid pack (tabs were broken), TPS. Removed the trans wiring harness and there is no damage or loose connections. When I replaced the solenoid connector I noticed there was some trans fluid in the connection. I cleaned it the best I could and reinstalled with dielectric grease.
The truck runs fine and shifts in and out of every gear fine its just shifting hard. If I unhooked the battery it will shift perfect for 5-10 minutes but then the hard shifting returns.
The only other thing I can find with my research is maybe the solenoid pack needs replaced. I figured if I take it somewhere they are going to want to rebuild/replace transmission. It seems like it can't be something very major since it will shift fine when reset...
View 4 Replies
