The back turn signals on my 93 ford taurus wont work but the front ones do. i checked the fuses and the bulbs and everything was good. the brake lights work and the head lights but no turn signals. same with the hazard lights. front ones work but no back ones. what should i try?
View 1 RepliesIn my 97 Ford Taurus the turn signals and hazards are not working. I changed the fuses, but still no luck. Someone mentioned that there might be another fuse box under the hood (besides the maxi fuse box). Also someone mentioned the blinker fluid being low.
View 14 RepliesI just got a 2000 F350 cc drw 7.3l.
I did search but have had no luck. My turn signals do not work, unless my foot is on the brake pedal my green arrow indicator wont even turn on. When they do my bulbs work but don't cycle so I know all the bulbs are good as I had my wife check all four corners when I got them to come on for a split second. I have tried replacing the MFS and the turn signal relay under the radio in the dash.... When I do turn on my blinkers I can hear the relay click once but that is it, no more.
I tried checking the wiring in the column and tilting the column to its extremes while trying to engage the turn signals. Also, if I unplug the brake light switch then I do not get an arrow on the IC to light up so I am guessing the power flows through that switch. I don't have a chilton manual yet and the owners manual was not in the truck. I did check fuse 23 ?
I noticed yesterday morning that my turn signals were not working on my 2000 F150 4.6L 4X4 XL truck and I need diagnosing what the cause is. The hazards, windshield wipers and my brights still work so I was not sure if it was just the switch. I have done the following:
* I went and got a new turn signal flasher at the parts store last night but when I went to put it in under the fuse box under the hood it was to big to fit into the holes. By this time the dealer was closed and I couldnt go and get a new one from them. (I wasn't sure if both needed to be replaced at the same time).
* Since there are two under the hood i just swapped the positions and still nothing happened everything worked accept my turn signals still worked. (by swapping I mean I took the one that was in fuse location 301 and put that one into 304 and 304 into 301.)
* I went to my owners manual and checked every fuse to make sure that anything related to my turn signals and flashers etc were not blown and they werent.
That is were I am at. I don't think its the switch but is that a common thing to go out?
My turn signals will not work with the engine running. With the engine off they will. With the engine running if I move the ignition like I am going to turn it off they work.. Is it the ignition switch or ign cylinder....
View 5 RepliesI have a 2003 Ford F150 King Ranch which I just bought, I noticed that the turn signals (both right and left) do not work and also the power mirrors are not working.
My 2003 Ford F150 has the 5.4 vortec, 4 x 4, automatic with 200K on it
I have a 2006 f150. Both front turn signals do not work. I replaced bulbs still nothing. There back signals do work. They blink really fast.
View 4 RepliesThis has been driving nuts for 2 days.... Brake lights dont work. Either pushing pedal or turning on lights. Turn signals work just fine.
Cab/cargo/3rd brake light on back of cab doesn't work either. I have checked/done the following:
- Checked Brake pedal switch for continuity. Tested fine.
- put multi meter on wiring all the way back to brake lights. No drop in voltage.
- changed bulbs. #3157 dual filament.
- positioned steering wheel all the way up and all the way down as suggested on here. No change.
- checked multi function switch (turn signal switch) for wiring issues. None found.
- kicked rear quarter panel for caveman adjustment out of frustration. No change.
What am I missing?
I have an 05 Freestar with no instrumentation and no error codes. None of the gauges work and most of the warning lights are lit when the truck is running. No A/C and no ABS while driving and turn signals work, but do not display on the dash. It appears that two separate code readers are not acknowledging the computer. The battery and alternator check out good and there is no drain on the battery when ign switch is off.
View 5 RepliesI have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 RepliesMy service advancetrac light comes on about once a month, seems random but when it does the turn signals will not work, you have to hold indicator in place for signals to work-not to safe. My local dealer has not been able to fix issue...
View 3 RepliesI'm having problems with my front marker lights. The turn signals work but when I turn on the parking lights or headlights they don't work. They only work with the turn signals. And I can't get the front side marker lights to come on. I've tried everything...
View 2 RepliesI just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights don't work.
The front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.
My second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.
2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
I just found a nice Prius C for sale with little damage to the front right corner, no frame damage or anything, just some bodywork needed. So, after it was fixed up. I brought the car back and there is weird issue that I have - turn signals and Hazard lights dont work. When I turn it on, i can hear clicks from it, but I dont see lights blinking on the dashboard and my head/tail lights dont blink as well.
View 5 RepliesI have a 2003 Chevy Malibu - periodically, they turns signals decide not to work. I don't know that one thing in particular causes them not to work. What could be the issue and is this something I can fix easily (I'm a novice), cheaply and quickly myself?
View 2 RepliesToday, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.
After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.
My sons 2006 F350 brake lights and rear turn signals quit working. When the headlights are on, all the lights operate but the rear turn signals and brake lights do not nor do the emergency flashers. The front signals work but flash very rapidly. Although I'm not an auto electrician, I'm fairly mechanically inclined but the fact that the front signals work, the rear don't and all lights work as lights, just not as turn signals or brake lights.
View 4 RepliesEvery time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
What is the easiest way to change the flasher?
View 6 RepliesRecently my tail lights went out and my turn signals dont work either, the light for the turn signal on the dash doesn't light up either. My brake lights do work tho and so do my reverse lights.
View 3 Replies