My '84 F150 4X4 inline 6 Died last night while driving. just conked out and died right there on the spot. no sputter... no gasping... just instant death...
after some investigation i found i wasn't getting spark anywhere. not at the plugs, not at coil. I have replaced the ignition module to no avail. still no spark I am going to swap in a the coil tonight. sure do hope this works.
So I bought my 1987 F150 XLT 4X4 (4spd) about two weeks ago and haven't had any issues with it so far... until now. As soon as I got it I did a full tune up. Changed plugs, cap, rotor, fuel filter, new battery, sea foamed it, fuel filter, ran a bottle of fuel stabilizer through it, new pvc valve, cleaned the throttle body, oil change, etc., ( all the usual things).
Was running fine up until two days ago when I was driving down the highway doing about 90km/hr in 4th when the truck suddenly lost power, sputtered and died. Tried to start it again and it will turn over but not start. So I get a nice expensive tow home and start to diagnose the problem. It is not a fuel issue. I can hear the pumps coming on, and fuel is coming out of the fuel filter so I cross that off the list.
Next I check for spark. No spark at all. So I run some tests. Battery is putting out 12V, about 10 when cranking. The solenoid is getting power and putting out power. No visible damage to any of the wiring, and all the grounds look good.
Next I just went ahead and swapped out the coil thinking that could be the issue. Didn't work. So I preform some more tests on the old and new coils. Both are grounded and having voltage pass through them. Next I take the TFI module off the distributor and check for resistance. Everything still checks out fine. Now I am thinking that the only thing left could be the PIP in the distributor. So instead of taking the dist apart and screwing around I go ahead a get a brand new dist and throw it in.
Now I am stoked and thinking that I finally fixed my truck and go to start it up and.... no spark. It still turns over but no start. I am trying to provide every bit of detail that I can. When I say I tested all the components I mean I REALLY tested them. I did both tests from the Haynes manual and from various sources off this site.
I am almost at the point of getting it towed to the shop, which I really do not want to do. A day before this happened I degreased the engine and VERY carefully sprayed it off with water. In the process I am thinking I may have damaged something?
I bought a 84 ranger 2.0 that ran when parked sat for six months. Cranks all day long but only sparks when you shut the key off. Replaced the ignition switch (by key) ( someone told me there is another ignition switch under the dash?? is this true?) Tested the icm and it passed all wires seem to be fine. I am just wondering if something in the dizzy could cause this or possibly the starter solenoid?
View 9 RepliesI have a 2011 Ford F150 FX4, And for a while now i have been having a issue with the gauge cluster.
while driving once in a while all of the gauge cluster turns off then back on within a couple of second. all the lights for the traction control, air bag, engine.... turn on and then turn off just like when you start the truck.
The issue only last for a couple of seconds. And it can go for a day before doing it. Brought it to the Ford dealership and they said unless the gauges are completely off there is nothing to go on by. Also once in awhile the check advancetrac comes on and will be off next time i start the truck. Same thing dealer said there was no codes and nothing then can do.
I checked all the connection at the fuse box, gauge cluster. and no issues. had the truck running and try wiggling all of the connectors, in the truck one by one with no success in duplicating the issue.
Also notice that once in awhile my signal light will flas extremely slow when having the blinker on.
I have an 06 F150 XLT and lately the map lights blink when starting and driving. This does not occur every time but it sure is a problem when driving at night. What is causing this and hopefully a minor repair.
View 1 RepliesI have a '84 Bronco and before I redid all the ignition wiring when I turned off the key the engine would stay running for about 6 seconds and then turn off. Now when I turn off the key and turn off a switch about 6-8 seconds later I here a click sound that comes from under and about center of the dash. And sometimes it clicks on and off in rapid secession kind of like when you flip a light switch on and off quickly. Some days it does it and some days it don't.
If I leave the battery hooked up then it drains the battery overnight or within a day, and sometimes its just fine. So to be safe I unhook the battery whenever its not being driven or started periodically. I am wondering what is in the center of the dash that needs power and that controls the ignition stuff?
My indicator lights are all out. The turn signals work correctly, as do the dash lights themselves, but all of the warning lights are out. The truck sat for three years and I have just gotten it back on the road.
View 7 RepliesLooking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 Replies I have a 1988 Bronco II 2.9 5 speed 4x4. Ive had it for about 2 years and the other day I put on a new cap and rotor and plug wires. I also cleaned the IAC. After that it ran fine for about a day and then I made a 2 hr trip and cut it off at a store. When i tried to recrank it, it just turned over and over and over for about 10 minutes and then it finally just cranked and ran like nothing was wrong. Its done the same thing twice since then (past 3 days) .
Yesterday when it did it, I pulled the coil wire and put a "spark tester" plug in the wire and tried cranking it. It only sparks right at the end when u quit cranking, itll spark 1 maybe 2 times. It'll crank if you just do a few short bursts of turning the ignition key to on. What else to check, or what the problem probably is? At first i was thinking it was the coil or module, but its only when cranking so maybe an ignition key problem or relay between there?
So I've been having problems with my old duraspark 2 ignition box and I replaced that but it didn’t seem to fix the problem. The truck doesn’t start if the voltage is down around 12v, it cranks but no spark. So I put it on the charger a couple hours ago and came inside and was reading old posts on here about testing the ignition system and then just went out to test the negative side of the coil with a test light and low and behold when my assistant went to crank it over the truck started right up like everything was fine. I took off the charger.
So then what I did was I checked the charge at the battery while the truck was running with a dvm and the voltage was 14.33 then I turned on the electric fan and it jumped up to 14.88 and spiked at 15 then held at 14.88. is that normal or is the voltage a little on the high side? If it is high then could it be the voltage regulator or alternator? And could that have been my problem all along instead of the ignition module?
I have a friend of mine that has a 1983 and he had me change the water pump in it because it started leaking and it has been sitting for 7 Months now. I changed that but I can't get this bugger to start. I used to be a mechanic in a past life so I know what I'm doing most of the time so let me explain what has transpired here.
I attached my remote starter, turned on the key and cranked over the engine after shooting a little bit of starting fluid in the carb and she cranks over but won't start. I then pulled the #1 spark plug out and then did the same thing to check for spark and nada. I put my light tester on the coil and there was power. I have run into this kind of problem years ago with other vehicles so I thought I would just go ahead and replace the Coil and also the Control Module. After replacing these parts, still no spark. Since the distributor is there only to distribute the spark (meaning no electrical connections to it) I'm assuming that the Pick Up part that is down by the Crank shaft might be bad.
How to test either the Control Module or the pick up. I'm trying to diagnose this problem without needing to remove the module and taking them to the parts house for testing. (long drive). These wires should have 12 volts when the key is off and these wires should have 12 volts when the key is on.... and so on.
1996 Ford F150 5.0 ... New battery, new alternator, new starter, new coil, dis cap good and rotor is good. New plugs and wires. Ignition mod tested good.
Drove a mile from my house and lost power to my engine. Lights and radio work. Just sits there and cranks and cranks. I'm not getting spark from the coil. Don't know a lot about engines.
I have an 86 f250 i just bought back with no spark. this truck is not original. used to be a diesel. has a 400 out of 81 f250. had this truck running just fine 4 years ago. sold it to a guy running and bought it back 4 yrs later not running.
Checked all the connection to make sure they r clean. Had the ignition modular tested and tested good. I have 12+ volts from the white and red wire. I have a little over 6 volts at the bat side of the coil. I have no spark from the coil. I notice every time I connect and disconnected the bat cable I will get a spark from the coil. i ran a test light from the tack test sight on the coil and tried to start and the light stayed real dim and never flickered.
Here's the breakdown. I have a '95 Ford F150 that I bought the previous year and it has been nothing but a problem. The most recent problem is the attempt to turn on the headlights. I will pull the plunger to turn on the headlights but I will only get the parking lights and when attempting to turn on the high beams I still get nothing. The only way that I get any sort of lighting is if I pull on the turning stick (almost like doing a manual override on a tripped wall plugin). Now here's the kicker. I still have parking lights, brake, tail, cab, and dash lights. Winter in quickly approaching and the nights are already getting dark, pretty soon the days will be just as dark.
View 3 RepliesI got my first truck today and it's a 1988 Ford F-150 and it runs great! The only issue is that the speedometer doesn't work and I won't be able to register it until it does. I was wondering what I can try out to maybe fix the issue and if not, how I would replace it. Every other gauge works, it's just the speedometer that isn't. The needle doesn't move at all it just sits at a 0 all the time.
View 8 RepliesI have been trying everything to get my speedo working on my Ford. It didn't work for 3 months after I got it then I decided to put some gear oil on the cable. This made it work for about 200 miles then it would only work with the clutch in and then not at all. I've replaced the speed sensor(not one on rear end the thing the cable goes into), and the gear that goes on the end of it. If I hook a drill up to the cable the tach moves. Could the cable be stretched or just needs some speedo cable lube?
View 5 RepliesI have a 1999 Ford F150 6 cyl. 4.2, 2 WD with 160,000 miles. Replaced the battery May 2010.
Today battery light came on. Battery gauge did not look like it was discharging. Had battery checked they said it was a little low but OK. Then they continued test and tried to check alternator, test stopped and they said something wrong with alternator most likely.
I took alternator out and had it bench tested. They said it was OK, putting out 98 amp on 95 amp alternator. They said check wires, grounds, harness, connections. Checked connections and wires as much as possible, reinstalled alternator, light still on.
Have not checked fuses yet. Was told to start vehicle, disconnect positive battery cable and if engine continued to run alternator was good, if cut off alternator was bad and to replace. Should I try this and is it true?
What is the part on the fire wall that is between the alternator and the battery that the wire connection runs through? Can it be bench tested/checked?
I have a 77 ford truck with a 351 ,the ignition system keeps shorting out, killing spark. If i replace the starter solenoid, it works for a while, then goes out again. I have replaced 4 solenoids this month. What could be shorting the solenoid out? Had the truck for 8 yrs. now, never had a problem with it till now. It has a mallory dist. it was in when i bought it.
View 7 RepliesMy center brake light went out a month ago. Thought it was the bulb so replaced that, still didn't work. Checked the fuse and its not broken so my guess was electrical?
Hasn't come on once that I know of but I was randomly walking behind my truck and the light was on. Truck was off lights were off and key wasn't in the ignition.
Went and turned my truck on and turned the lights on and the cbl stayed on. When I switched my lights off it went out and stayed out.
Now I'm definitely thinking wiring but not sure where to start fixing?
Oh and it's a 1990 F150 XLT
Just bought a used, 03 F-150 SuperCrew Lariat. Having some minor electrical issues. While cleaning truck, I discovered a red wire coming into engine area on passenger side of vehicle. Wire has a built in 40amp fuse but isn't connected to anything. What this is for/ should be connected to???
View 1 RepliesAfter replacing my battery cables (Pos and Ground),My Truck stalls every time I turn on the headlights. The truck stays running with the parking lights on or if no lights on at all. Could I have mixed up the 2 positive accessory wires?
View 13 Replies